LIBRETTO ISTRUZIONI E GB Manual de instrucciones Instruction book IG 645.
Contents Safety instructions 38 Disposal 38 Economical and ecological dishwashing 38 Description of the appliance 39 The control panel 39 Prior to using for the first time Setting the water softener Filling with salt Rinse aid 40 40 41 41 In daily use Loading cutlery and dishes The lower basket The cutlery basket The upper basket Adjusting the height of the upper basket Use of detergent 43 43 43 43 44 44 45 Washing programmes 46 Starting a washing programme 47 Maintenance and cleaning Clea
Safety instructions It is most important that this instruction book should be retained with the appliance for future reference. Should the appliance be sold or transferred to another owner, or should you move house and leave the appliance, always ensure that the book is left with the appliance in order that the new owner can get to know the functioning of the appliance and the relevant safety information. ● This information has been provided in the interest of your safety.
Description of the appliance 1. Upper basket stop 2. Water hardness switch 3. Salt container 4. Detergent dispenser (type A / type B) 5. Control panel 6. Rating plate 7. Rinse aid dispenser (type A / type B) 8. Filters 9. Lower spray arm 10. Upper spray arm 11.
Prior to using for the first time Before using your dishwasher for the first time: Setting electronically 1. Ensure that the electrical and water connections comply with the installation instructions The dishwasher is factory set at level 3. If it’s necessary to set a new level, proceed as follows. 2. Remove all packaging from inside the appliance 1. With the dishwasher switched off press function push buttons 1 and 2 simultaneously . 3. Set the water softener 4.
Filling with salt Rinse aid Rinse aid is automatically added during the last rinse, ensuring thorough rinsing, and spot and streak free drying. The dispenser, which is positioned inside the door, holds about 110 ml of rinse aid, which is sufficient for 16 - 40 dishwashing programmes, depending upon the dosage setting. Special salt can be added in one of two ways: ● ● If you are using dishwasher detergent that already contains salt, the detergent including the salt is placed in the detergent compartment.
Filling with rinse aid To deactivate the rinse aid indicator light proceed as follows: (Rinse aid dispenser type B) (the dishwasher must be switched off) 1. Open the container by turning the lid (A) anticlockwise. 1. Press function push buttons 1 and 2 simultaneously. 2. Fill with rinse aid exactly up to the level indicator marked "max". 2. While keeping the function push buttons 1 and 2 pressed switch on the dishwasher by pressing the On/Off push button. The On/Off indicator light comes on.
In daily use ● Check if it’s necessary to refill with special salt or rinse aid ● Load cutlery and dishes into the dishwasher. ● Fill with dishwasher detergent . ● Select a wash programme suitable for the cutlery and dishes. ● Start the wash programme. Loading cutlery and dishes Sponges, household cloths and any object that can absorb water may not be washed in the dishwasher. ● Before loading the dishes, you should: - Remove large left-overs.
Cutlery should be placed in the removable cutlery basket with the handles facing downwards. If the handles protrude from the bottom of the basket, obstructing the lower spray arm, load the cutlery with the handles facing upwards. Adjusting the height of the upper basket If washing very large plates you can load them in the lower basket after moving the upper basket to the higher position. Mix spoons with other cutlery to prevent them from sticking together.
Use of detergent Detergent tablets Only use detergents specifically designed for use in dishwashers. Detergent tablets of different brands dissolve at different speeds. For this reason some detergent tablets cannot develop their full cleaning power during short programmes. Therefore please use normal programmes with prewash when using detergent tablets. Using no more then the correct amount of detergent contributes to reducing pollution. Prior to the start of a wash programme.
Washing programmes Programme Intensive 70° Normal 65° (1) Quick 65° (2) Eco 50° Degree of soil and type of load Heavy soil. Crockery, cutlery, pots and pans Normal soil. Crockery and cutlery Fresh soil. Crockery and cutlery Normal soil.
Starting a washing programme 1. Check that the baskets have been loaded correctly and that the spray arms can rotate freely 7. End of the washing programme The dishwasher will automatically stop and the end of programme phase indicator light will illuminate. The indicator light of the programme just ended will remain on. The dishwasher has finished the programme only when the end of programme indicator light is illuminated.
Maintenance and cleaning Under no circumstances may the dishwasher be used without filters. Incorrect repositioning and fitting of the filters will produce poor washing results. Clean the external surfaces of the machine and control panel with a damp soft cloth. If necessary use only neutral detergents. Never use abrasive products, scouring pads or solvent (acetone, trichloroethylene etc....).
What to do, when... Certain problems are due to the lack of simple maintenance or oversights, which can be solved with the help of the instructions given here, without calling out an engineer. ...a flashing fault code appears The dishwasher will not start or stops during operation. All push buttons are inoperative except for the On/Off push button and a combination of indicator lights, as indicated in the following chart, are flashing.
...the wash results are not satisfactory The dishes are not clean ● ● ● ● ● ● ● ● The wrong washing programme has been selected. The dishes were arranged in such a way as to stop water reaching all parts of the surface. The baskets must not be overloaded. The spray arms do not rotate freely due to wrong arrangement of the load. The filters in the base of the washing compartment are dirty or incorrectly positioned. Too little or no detergent has been used.
Installation instructions Any electrical and/or plumbing work required to install this appliance should be carried out by a qualified electrician and/or plumber or competent person. Water supply connections This dishwasher may be fed with either hot (max. 50°) or cold water. Nevertheless we advise you a cold water supply. A hot water supply is not always efficient with very soiled crockery as it shortens the washing programmes a lot. Remove all packaging before positioning the machine.
Water outlet hose connection Electrical connection The end of the drain hose can be connected in the following ways: Information concerning the electrical connection is given on the rating plate on the edge of the dishwasher’s door on the right. 1. To the sink outlet spigot, securing it to the underside of the work surface. This will prevent waste water from the sink running into the machine. Before plugging the appliance into the wall socket, make sure that: 1.
Hints for test centres Testing in accordance with EN 60704 must be carried out with appliance fully loaded and using the test programme (see "Washing programmes" chart). Test in accordance with EN 50242 must be carried out when the salt dispenser and rinse aid container have been filled with salt and rinse aid respectively and using the test programme (see "Washing programmes" chart).
Küppersbusch Vertriebsgesellschaft mbH Postfach 10 01 32, D-45801 Gelsenkirche, Küppersbuschstraße 16, D-45883 Gelsenkirchen Telefon (02 09) 4 01-0, Telefax (02 09) 4 01-3 03 152969 22/0 Con riserva di modifiche - Salvo modificaciones Subject to change without notice 0 01/03