Rain Sensor Suspends Automatic Irrigation Systems OWNER’S MANUAL AND INSTALLATION INSTRUCTIONS 3208-WRFS Wireless Rain/Freeze Sensor 3208-HRFS Rain/Freeze Sensor 3208-HRS Rain Sensor Save water and ensure healthy landscapes by suspending your irrigation system on rainy days. K-Rain sensors offer flexible, multiple rainfall settings which are quick and easy to adjust. K-Rain Manufacturing Corp. 1640 Australian Avenue | Riviera Beach, FL 33404 USA 561.844.1002 | FAX: 561.842.9493 | 1.800.735.
1. Manual Test Pin 4. Rainfall Adjustment Cap 3. Mounting Arm 5. Freeze Sensor (internal) 2. Vent Adjustment Tab 6. Radio Antenna 7. Battery / Transfer Signal LED (beside Radio Antenna) RAIN SENSOR COMPONENTS 1. Manual Test Pin. Press and hold for three seconds to confirm proper operation. 2. Vent Adjustment Tab. Used to adjust the dry out time of the sensor. 3. Mounting Arm. Metal extension arm for mounting the sensor. 4. Rainfall Adjustment Cap.
TABLE OF CONTENTS Rain Sensor Components 1 Introduction 2 Features 2 Installation 3 Mounting the Rain Sensor 7 Adjustments and Operation 8 Specifications 9 Troubleshooting 9 FCC Declaration of Conformity 10 Warranty and FCC Notice 11 INTRODUCTION Thank you for selecting a K-Rain® Rain Sensor. This sensor will turn your irrigation controller into an expert water manager by efficiently suspending watering during rain and/or freeze periods.
INSTALLATION: 3208-WRFS 1. Install the RF Module receiver (Model 3206) into your Pro EX 2.0 Controller. 2. Pair your 3208 Wireless Rain-Freeze Sensor with the Pro EX 2.0 Controller. a. Place dial on pin position. Press UP button until “LEARN” is displayed on the LCD. A PGM START LEARN b. Press the START button, and the word “LEARN” will flash. LEARN c. Press the Manual Test Pin for three seconds to enable the wireless rain sensor to transmit the signal d.
e. Press the DOWN button to complete the process. Move the dial back to AUTO. NOTE: The manual activation of some controllers bypasses the sensor inputs. The controller must be in Automatic mode in order for the sensor to work properly. LEARNED Sensor Additional Features of the 3208-WRFS (Wireless Rain Freeze Sensor) • The Pro EX 2.0 Wifi enabled controller comes from the factory with wired rain sensor terminal enabled. Once a wireless rain sensor has been paired with the Pro EX 2.
INSTALLATION: 3208-HRFS/3208-HRS WIRING Models 3208-HRFS (Rain Freeze Sensor) or 3208-HRS (Rain Sensor) IMPORTANT: The rain sensor is designed for 24-VAC irrigation controllers only. All wiring must conform to applicable local building codes and regulations. K-Rain Rain Sensors will not work with open circuit timers. 1.
Common Wire from Valves Wire Connector 3. Installing the wired rain sensors 3208-HRFS or 3208-HRS into controllers with pump start/master valve terminal; and without sensor terminals: FIGURE 2 Irrigation System Controller 1 2 3 4 PUMP/ COM MV 24 VAC To Valves Pump Start Relay/ Master Valve Common Wire from Valves Wire Connector B. 24-VAC Solenoid Valves with Pump Start Relay (See Figure 2).
MOUNTING THE RAIN SENSOR STANDARD FLAT MOUNTING Mount the sensor on a surface that is unobstructed to rain fall, but away from the path of the sprinkler water spray. GUTTER MOUNTING Allows the rain sensor to be mounted directly to the side of the gutter. Position the gutter mount on the edge of the gutter and twist the thumbscrew to secure it in place. HINTS FOR MOUNTING a.
ADJUSTMENTS AND OPERATION When the Rain Sensor activates due to sufficient rainfall (after rainfall quantities of 1/8" through 1/2" or more), the sprinkler system will become inactive until the moisture-absorbent discs inside the Rain Sensor have dried out. To adjust to the desired quantity of rainfall, rotate the cap on the rain sensor housing to the range desired (See Figure 3). FIGURE 3 HIGH END LOW END Adjust the dial to the amount of rainfall you wish to trigger the rain sensor to suspend watering.
SPECIFICATIONS Mounting: 2 in 1 bracket for standard flat and gutter installation Sensor Type: Industry-standard hygroscopic disc stack with adjustable rainfall sensitivity Rating: 3 amp, 24 V AC, NC (Normally Close contacts) Operating Temperature Range: 14°F to 149°F (-10°C to 65°C) Hardware: Stainless steel Housing: UV-resistant engineered polymer Rain Sensor Warranty: Two years ADDITIONAL SPECS FOR WIRELESS VERSION: Rain/Freeze Wireless Range: Up to 400 feet or 120 meters (Line of Sight) Freeze Set Point
FCC DECLARATION OF CONFORMITY Trade Name Wireless Rain Freeze Sensor Model Number 3208-WRFS Compliance Test Report Number 16FAB01000511 Compliance Test Report Date March 22, 2016 Responsible Party K-Rain Manufacturing Corporation Address 1640 Australian Ave, Riviera Beach, FL 33404 Telephone 561-844-1002 This equipment has been tested and found to comply with the limits for class B digital devices, pursuant to part 15 of the FCC Rules.
WARRANTY K-Rain Manufacturing warrants that its products will be free from materials and workmanship defects for a period of 2 years. With proof of purchase provided, K-Rain will replace, free of charge, the defective part or parts found to be defective under normal use and service for the warranty period. Prior to replacement, K-Rain reserves the right to inspect and authorize the defective part or parts; all defective material returns must be authorized in writing by K-Rain.
Sensor De Lluvia Suspende Sistemas Automáticos de Irrigación MANUAL DEL PROPIETARIO E INSTRUCCIONES DE INSTALACIÓN 3208-WRFS Sensor Inalámbrico de Lluvia/Congelación 3208-HRFS Sensor de Lluvia/Congelación 3208-HRS Sensor de Lluvia Ahorra agua y garantiza paisajes bien cuidados mediante la suspensión de su sistema de riego en días lluviosos. El sensor de lluvia de K-Rain permite ajustar la cantidad de lluvia que el usuario desee utilizar, para suspender su controlador automático.
1. Embolo para prueba manual 4. Tapa de Ajuste de Lluvia 3. Brazo de Montaje 5. Sensor de Congelación (interno) 2. Rejilla de ventilación Ajustable 6. Antena de Radio 7. Batería / Transferencia de Señal LED (Al lado de la Antena de Radio) COMPONENTES DEL SENSOR DE LLUVIA 1. Embolo para prueba manual. Pulse y mantenga pulsado durante tres segundos para asegurar un correcto funcionamiento. 2. Rejilla de ventilación ajustable. Se utiliza para ajustar el tiempo de secado del sensor. 3. Brazo de Montaje.
TABLA DE CONTENIDO Componentes del Sensor de Lluvia 1 Introducción 2 Características 2 Instalación 3 Montaje del Sensor de Lluvia 7 Ajustes y Funcionamiento 8 Especificaciones 9 Solución de Problemas 9 Declaración de Conformidad FCC 10 Garantía y Aviso de la FCC 11 INTRODUCCIÓN Gracias por seleccionar el Sensor de Lluvia K-Rain®.
INSTALACIÓN: 3208-WRFS 1. Instalar el modulo receptor de RF (Modelo 3206) en su Controlador Pro EX 2.0. 2. Asociar el Sensor Inalámbrico de Lluvia y Congelación 3208 con el controlador Pro EX 2.0. a. Coloque el dial en la posición PIN. Pulse el botón UP hasta que visualice “LEARN” en la pantalla LCD. A PGM START LEARN b. Pulse el botón START, y la palabra “LEARN” comenzará a parpadear. LEARN c.
e. Presione el botón para completar el proceso. Mueva el dial a AUTO. LEARNED Sensor NOTA: El ciclo de activación manual de algunos controladores no pasa por las entradas del sensor. El controlador debe estar en modo Automático para que el sensor pueda trabajar apropiadamente. Características Adicionales del 3208-WRFS (Sensor Inalámbrico de Lluvia y Congelación) • El controlador Pro EX 2.0 con Wifi viene de fábrica con el terminal cableado del sensor de lluvia activado.
INSTALACIÓN: 3208-HRFS/3208-HRS Modelos CABLEADO 3208-HRFS (Sensor de Lluvia y Congelación) o 3208-HRS (Sensor de Lluvia) IMPORTANTE: El sensor de lluvia ha está diseñado para controladores de riego de 24-VAC solamente. Todo el cableado debe cumplir con los códigos de construcción locales y regulaciones aplicables. Los Sensores de Lluvia K-Rain no funcionarán con temporizadores de circuito abierto. 1.
Common Wire from Valves Wire Connector 3.
MONTAJE DEL SENSOR DE LLUVIA VIA MONTAJE PLANO ESTANDAR Montar el sensor en una superficie que este accesible a la caída de lluvia, pero lejos de la trayectoria de la pulverización de agua de los rociadores. MONTAJE EN CANALETA Permite que el sensor de lluvia pueda montarse directamente en el lado de la canaleta. Posicione el montaje en el borde de la canaleta y ajuste el tornillo para una sujeción segura. CONSEJOS PARA MONTAJE a.
AJUSTES Y FUNCIONAMIENTO Cuando se activa el Sensor de Lluvia debido a la precipitación de lluvia suficiente (después de una cantidad de lluvia de 1/8" (0,32 cm) a 1/2" (1,3 cm) o más), el sistema de rociadores quedará inactivo hasta que los discos absorbentes de humedad en el interior del Sensor de Lluvia se han secado. Para adaptarse a la cantidad deseada de precipitaciones, gire la tapa en la carcasa del sensor de lluvia a la gama deseada (Ver figura 3).
ESPECIFICACIONES Montaje: Soporte 2 en 1 para la instalación plana y en canaleta Tipo de Sensor: Paquete de discos higroscópicos estándar de la industria, con sensibilidad a precipitaciones ajustable Valoración: 3 amp, 24 VAC, NC (normalmente cercanos de contactos) Rango de Temperaturas de Funcionamiento: 14 °F to 149 °F (-10 °C to 65 °C) Montura: Acero inoxidable Cubierta: Polímero de ingeniería resistente a los UV Garantía del Sensor de Lluvia: Dos años ESPECIFICACIONES ADICIONALES PARA LA VERSION INALAMB
DECLARACIÓN DE CONFORMIDAD DE LA FCC Nombre Comercial Wireless Rain Freeze Sensor Número de Modelo 3208-WRFS Número del Informe de Prueba 16FAB01000511 Fecha del Informe de Prueba March 22, 2016 Empresa Responsable K-Rain Manufacturing Corporation Dirección 1640 Australian Ave, Riviera Beach, FL 33404 Teléfono 561-844-1002 Este equipo ha sido probado y cumple con los límites para dispositivos digitales de clase B, según la parte 15 de las normas de la FCC.
GARANTÍA K-Rain Manufacturing garantiza que sus productos estarán libres de defectos de materiales y mano de obra por un período de 2 años. Con la prueba de compra prevista, K-Rain reemplazará, sin costo alguno, la parte o partes defectuosas que se encuentre defectuoso en condiciones de uso normal y durante el período de garantía.