K 2.32 M Operating Instructions Before first use of the unit read these operating instructions and act in accordance with them. 5.963-125.
Contents General information Description of the Appliance Safety instructions Operation Transport Storage Maintenance and care Troubleshooting Helpline Technical specifications CE declaration Spare Parts Symbols on the machine 2 3 4 6 7 8 8 9 9 10 10 11 General information Dear Customer, Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners.
Description of the Appliance 1 2 3 4 5 6 7 8 9 High pressure connection Detergent suction hose (with filter) Appliance switch "0/OFF“/ „I/ON“ Carrying handle Storage for trigger gun Storage for spray lance Water connection Coupling element for water connection Mains cable with mains plug 10 11 12 13 14 15 16 17 Bearing wheel Trigger gun Lock trigger gun Clamp for high pressure hose High pressure hose Spray lance with Dirtblaster Spray lance with high pressure nozzle Washing brush English 3
Safety instructions Danger Never touch the mains plug and the socket with wet hands. The appliance must not be used if the power cord or important parts of the appliance, e.g. high-pressure hoses, trigger gun or safety devices are damaged. Check the power cord and mains plug for damage before every use. If the power cord is damaged, please arrange for it to be replaced immediately by an authorised repair agent or a skilled electrician Check the high-pressure hose for damage before every use.
Wear protective clothing and safety goggles to protect against splash back containing water or dirt. Caution In case of extended downtimes, switch the appliance off at the main switch / appliance switch or remove the mains plug. Do not operate the appliance at temperatures below 0 °C. Observe a distance of at least 30 cm when using the jet to clean painted surfaces to avoid damaging paintwork. Never leave the appliance unattended when it is in operation.
Operation Before Startup Illustrations on Page 3 Mount loose parts delivered with appliance prior to start-up. Î Illustration Insert the transport wheels and lock them. Î Illustration Pull out the clamp for the high-pressure hose from the trigger gun (e.g. a small screwdriver). Î Illustration Connect high pressure hose to trigger gun. Push the clamp in until it locks. Check the secure connection by pulling on the high-pressure hose.
Working with detergent Finish operation Please use exclusively KÄRCHER detergents and care products to carry out the respective cleaning task, as these were specifically developped for your appliance. The use of other detergents and care products may lead to premature wear and can invalidate your warranty claims. Please obtain information at your local dealer or request information directly from KÄRCHER. Î Pull detergent suction hose as far as is required out of the housing.
Storage Caution In order to prevent accidents or injuries, keep in mind the weight of the appliance when selecting a storage location for it (see Specifications). Storing the Appliance Prior to extended storage periods, as during the winter, also observe the instructions in the Care section. Î Park the machine on an even surface. Î Insert the trigger gun in its holder. Î Insert spray lances in their holder. Î Stow away the mains cable, the highpressure hose and accessory at the appliance.
Troubleshooting You can rectify minor faults yourself with the help of the following overview. If in doubt, please consult the authorized customer service. Danger Turn off the appliance and remove the mains plug prior to any care and maintenance work. Repair works may only be performed by the authorized customer service. Appliance is not running Î Pull on the lever of the trigger gun; the device will switch on.
CE declaration Technical specifications Electrical connection Voltage 220-240 V 1~50/60 Hz 6A IP X5 II 13 A Power consumption Protection class Protective class Mains fuse (slow-blow) Water connection Max. feed temperature 40 °C Min. feed volume 8 I/min Feed pressure 0,2-1,2 MPa Performance data Working pressure 8 MPa Max.
Spare Parts English 11