User's Manual

ManualsBrandsKAB ManualsElectronicsRemote Controller

OUTDOOR 3-OUTLET TIMER

WITH REMOTE CONTROL

INSTALLATION INSTRUCTIONS

OPERATING INSTRUCTIONS

MAINTENANCE

SAFETY INFORMATION

Installation

a. Mount the timer onto a wall near a grounded

electrical outlet with the photo sensor facing

outward.

Note: To ensure proper operation of automatic

function, ensure photocell sensor is shielded

from all nighttime sources of light, i.e.

floodlights.

b. Insert nail or screw (not included) into mounting

surface. Nail or screw head must extend at least 3/16 in. out from the

wall. Hang the receiver from the slot on back of the unit onto the nail or

screw. Plug the power supply cord of the receiver into the outlet.

c. Plug the device cord into any of the three receptacles at the bottom of

the receiver.

1. Button Layout

2. Timer and remote interaction

Your timer includes a remote control with temporary

override:

• Temporary override ON:

turns the timer ON for desired settings (2, 4, 6 or

8 Hours). Please note that if the timer is set to a 2-,

4-, 6- or 8-hour mode, it will come on at dusk and

will turn off 2, 4, 6, or 8 hours later.

• Temporary override OFF: turns the timer OFF.

3. Examples

• Timer set to DUSK-DAWN When DUSK = 6:00 PM

and DAWN = 5:00 AM.

- If at 4 :00 PM REMOTE activated to ON --> TIMER

OUTPUT ON and stays ON until 5:00 AM.

- Next day, ON at DUSK, OFF at DAWN.

- If at 10:00 PM REMOTE activated to OFF --> TIMER

OUTPUT OFF = 10:00 PM and stays OFF until

DAWN next day.

- Next day ON at DUSK, OFF at DAWN.

• If TIMER setting is 2 HOURS (or 4, 6, 8 HOURS and so on) DAY OR

NIGHT TIME REMOTE ON --> TIMER OUTPUT ON 2 HOURS (4, 6, 8

HOURS) then OFF.

When DUSK --> TIMER OUTPUT ON 2 HOURS (4, 6, 8 HOURS) then

OFF. If DUSK is at 6:00 PM:

(1) If at 5:00 PM REMOTE set ON, then TIMER OUTPUT ON immediately

until 7:00 PM.

(2) TIMER ON = 6:00 PM, TIMER OFF = 8:00 PM. If at 1:00 PM REMOTE

set ON, then TIMER OUTPUT turns ON until 3:00 PM.

(3) TIMER ON = 6:00 PM. If at 7:00 PM REMOTE set ON TIMER OUTPUT

ON until 9:00 PM (as time count restarted at time remote activates to

ON).

(4) TIMER ON = 6:00 PM. If at 7:00 PM REMOTE set OFF, then TIMER

OUTPUT turns OFF immediately until next day.

SPECIFICATIONS:

14/3 AWG SJTW vinyl cord

RATINGS:

125Vac 60Hz

15 A General Use

15 A Resistive

1,000 W Tungsten

500 VA Electronic Ballast, 1/2 HP

120Vac 60Hz 8.3A Ballast.

Dial position Function

OFF Power OFF

ON Power ON

2 Hrs ON at dusk – OFF in 2 hours

4 Hrs ON at dusk – OFF in 4 hours

6 Hrs ON at dusk – OFF in 6 hours

8 Hrs ON at dusk – OFF in 8 hours

DUSK-DAWN Powers ON at dusk, OFF at dawn

Timer Dial position Using the Remote

OFF Press the remote and the timer will turn ON/OFF

ON Press the remote and the timer will turn ON/OFF

DUSK-DAWN

2, 4, 6 or 8 HRS

Press the remote and it will go into a manual

restart mode. The timer will restart from ‘0’ and

count until it reaches the time set on the dial, or

dawn. Please refer to examples below for further

explanation.

HELPFUL TIPS

• Before using your timer, please read the following instructions carefully.

• When set to “ON”, the timer will provide continual power to attached devices

until the timer is switched to “OFF”, or to any of the other operating modes.

Receiver

Transmitter

1. Timer unit: The timer will control an array of devices by setting the dial.

2. Remote control:

• ON: When the on button is pressed, it will override the timer’s current

program to on function.

• OFF: When the off button is pressed, it will override the timer’s current

program to off function.

• Remote indicator light: The LED light indicates that the ON or OFF

button is being pressed.

3. Timer dial: Rotate the dial on the timer to select one of the following settings

4. Power indicator light: The power indicator light indicates that the timer is

on.

5. Photo sensor: The sensor will sense for light and dark, and direct the

timer to act accordingly.

6. Outlets: The three outlets located on the button of the timer allows the

user to plug an array of devices into it.

WARNING:

• The device must be mounted in a vertical position with the receptacle facing

downward and with the receptacle at least 1.4 M above the ground level.

• Let the switch hang downward so moisture does not accumulate in the outlet.

• Suitable for Outdoor Use, Store indoors when not in use. Not for water

immersion or for use were directly exposed to water

• Cord-connected Operating control

• Temperature limits of the SWITCH HEAD: -40~40℃。

TROUBLESHOOTING

Problem

Solution

The lights do not turn on,

even when the timer is in

the “ON” position.

Ensure the lights are functional by plugging them directly

into the outlet.

The lights do not turn on

2,4,6, or 8 hrs. after dusk.

Be sure that the timer is not near ambient light sources.

The lights do not turn on

and off via remote control.

Confirm remote operation after replacing batteries.

Be sure that the dial is fully turned to the “ON” position by

listening for the clicking sound.

Be sure that the lights are in the “ON” position if they have

their own switch.

Be sure that the outlet that the timer is plugged into is

active.

Confirm that the timer is plugged properly into the outlet,

and that the light is turned on if there is a switch.

SAVE THESE INSTRUCTIONS!

Battery Handling and Usage

Keep batteries away from children and pets.

• Follow the battery manufacturer’s safety and usage instructions.

• Insert the battery observing the proper polarity (+/-) as indicated inside

Battery Compartment.

• Remove a spent or discharged battery from the product. Remove the

battery when not using the product for an extended period.

• Never throw batteries into a fire. Do not expose batteries to fire or other

heat sources.

• Dispose or recycle spent / discharged batteries in compliance with all

applicable laws. For detailed information contact your local solid waste

authority.

• Battery contains mercury. Do not put in trash. Recycle or manage as

hazardous waste.

WARNING:

Federal Communications Commission Interference Statement

This equipment has been tested and found to comply with the limits for Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference,

and (2) this device must accept any interference received, including

interference that may cause undesired operation of the device.

FCC Caution: The Grantee is not responsible for any changes or modifications

not expressly approved by the party responsible for compliance. such

modifications could void the user's authority to operate the equipment.

OFF

CAUTION: Failure to properly align the battery polarity can cause personal injury and/or

property damage.

Replacing the battery

• Remove the Battery compartment cover from

the back of the remote control.

• Remove the spent battery and place a new Type

CR2032 battery into the Battery Compartment

correctly observing the polarity indications (+/-)

inside the Battery Compartment.

• Replace the Battery Compartment Cover.

• Clear the battery contacts and also those of

the device prior to battery installation

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov

RECEIVER MODEL: TM-069R

TRANSMITTTER MODEL: TR-026A-S

FCC ID: PAGTR-026A-S

IC: 4494A-TR026AS

Industry Canada statement:

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not

cause interference, and (2) this device must accept any interference, including

interference that may cause undesired operation of the device.

Déclaration d’Industrie Canada :

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence. L'exploitation est autorisée aux deux

conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même

si le brouillage est susceptible d'en compromettre le fonctionnement.

Made in China

SAVE THESE INSTRUCTIONS!

Unique Identifier :

KAB Model No. : TM-069R/TR-026A-S

Responsible Party - U.S. Contact Information

Company Name :

Customer Address :

Tel/Internet Contact :

Replacing the battery

TR-026A-S Remote Controller User Manual

FRONT BACK