ASSEMBLE INSTRUCTION 10FT X 10FT ALUM DOUBLE ROOF GAZEBO Website: www.casainc.com Contact Phone Number: （303)747-4321 Email us: service@casainc.
Safety Information WARNING: Keep all flame and heat sources away from this tent fabric. This tent is made with fabric that meets CPAI-84 specification for flame resistance. It is not fire proof. The fabric will burn if left in continuous contact with any flame source. The application of any foreign substance to the tent fabric may render the flame-resistance properties ineffective.
Pre-Assembly PLANNING ASSEMBLY It will take at least two people about 90 minutes to complete the assembly process. A rubber mallet and a free standing ladder are needed during the process. IMPORTANT: Please count the number for each part before assembly. PART LIST NOTE: Parts not shown to actual size. ITEM DESCRIPTION QTY.
Pre-Assembly ITEM DESCRIPTION QTY. O U-Shaped Connector Q ILLUSTRATION ITEM DESCRIPTION QTY. 4 BB Roof Sheet 4 Support Arm 8 CC Roof Sheet 4 Y Roof Sheet 4 DD Roof Sheet 4 Z Roof Sheet 4 EE Roof Mosquito Net 1 AA Roof Sheet 4 FF Mosquito Net 4 ILLUSTRATION Important: Do not remove the protective film from the roof sheets until you are ready to attach them to the frame in Step 13 &18 .The surface with protective film is the outer side.
Assembly 1. Attaching netting rails LL A C LL A/B LL LL C LL LL B C LL LL LL Attach one netting rail (C) to each cross beam (A) & (B) with self-tapping screws (LL) using Philips screw driver (PP). Do not fully tighten all the self-tapping screws (LL) until the end of this step. 2. Assembling cross beams II P II P A II P A/B II P II P B Attach two U-brackets (P) to the top of each cross beam (A) & (B) with bolts (II) using wrench (NN).
Assembly 3. Assembling cross beams A O B A B A O B II Plug U-shaped connector (O) into each cross beam (B), using bolts (II) loosely secure them together until the end of this step. Repeat this for cross beam (A) until complete cross beams (A) & (B) are formed. Fully tighten all the bolts (II). 4. Erecting the main frame II B A B A B A II B A B D A D II D D D Stand the corner post (D) up.
Assembly 5. Attaching support arms Q Q Q Q Q Q II II Q Q Q Q Adjust corner post (D) upright. Attach support arms (Q) to cross beams (A) / (B) and corner posts (D) with bolts (II) using wrench (NN).Do not fully tighten all the bolts (II) until the end of this step. 6. Assembling the roof frame E E R click! E E R E E E Snap one corner roof tube (E) into each receiver of the roof hub (R) until you hear a click.
Assembly 7. Attaching the roof frame E JJ E D D Attach each corner roof tube (E) onto the bracket at the top pf each corner post (D) with bolts and nuts (JJ) using wrench (NN). 8. Attaching the roof sheet rails (F,G,H,I) H I F G I/G G H/F I F H H F I W G G F E I H II Attach roof sheet rails (I) and (H) onto the corner roof tube (E) with washer plates (W) and bolts (II) using wrench (NN). Do not fully tighten bolts until the end of step 20.
Assembly 9. Attaching roof sheet rails (F,G,H,I) H I F G G I/G I F JJ H H F I G G F I H Attach roof sheet rails (I) and (H) onto the brackets on top of cross beams (A) / (B) respectively with bolts and nuts (JJ) using wrench (NN) and (OO). Follow the above procedure to attach the roof sheet rails (G) and (F) onto the frame. 10. Assembling the small roof frame click! J J R J R J J J J J Snap one corner roof tube (J) into each receiver of the roof hub (R) until you hear a click.
Assembly 11. Attaching the small roof frame J J V E JJ S E J U R JJ V T E Fix the roof spacer brackets (U) under this last assembly by covering and screwing the roof hub cover (S) on. Lay down this assembly over the first roof hub (R) fitted with corner roof tube (E). Fix by using the hook (T) as shown. Fix other ends of corner roof tube (J) to the corner roof tube (E) by using the roof spacer brackets (V) and bolts and nuts (JJ) using wrench (NN). 12.
Assembly 13. Insert roof sheet for small roof J Y Y Y Y Y Y Y Insert one piece of roof sheet (Y) into the groove of corner roof tube (J). IMPROTANT: Before insert next roof sheet (Y) you should finish till the step 15. The roof sheet should insert one by one. 14. Insert roof rim for small roof Y J Y K K K K K K As illustrated, insert one piece of roof rim (K) at the end of last assembly roof sheet (Y) of small roof.
Assembly 15. Attaching end cover for small roof GG GG GG GG GG KK Secure last assembly roof sheet (Y) by using corner end cover (GG) with self-tapping screw (KK). In order not to damage inserts, do not over tighten the screws. Repeat step 13 to step 15 to finish insert all four roof sheets (Y). 16. Install washer plate X X X X X G/F X X X X II As illustrated, install washer plate (X) to roof sheet rail (G) & (F) by using bolts (II).
Assembly 17. Attaching small support crossbars N N N N N N N W N N N N N N N N N X Insert small support crossbars (N) on pins of washer plate (X) and (W) as shown. 18. Attaching roof sheets Z DD AA CC CC BB AA BB CC DD Z G AA Z DD CC BB BB CC AA DD Z AA Insert one piece of roof sheet (Z) into the groove of roof tubes as shown. IMPROTANT: Before insert next roof sheet (AA) you should finish till the step 20. The roof sheet should insert one by one.
Assembly 19. Attaching roof rim M M G M M M M M M M M M M M M M M M M M M M M As shown, insert one piece of roof rim (M) at the end of last assembly roof sheet rail. 20. Attaching end cover for big roof GG HH HH HH HH HH HH GG HH HH GG KK HH GG HH HH HH HH HH HH HH GG HH KK Secure last assembly roof sheet by using corner end cover (GG) and side end cover (HH) with self-tapping screw (KK). In order not to damage inserts, do not over tighten the screws.
Assembly 21. Assembling roof mosquito net EE T L EE EE Loosen the hook (T). Fix the roof mosquito net (EE) to the small roof. Tighten the hook (T) through the buttonhole on the roof mosquito net (EE). 22. Assembling mosquito net C FF FF FF FF D FF Hang up the mosquito net (FF) into the net hooks.
Assembly 23. Fix ground stakes D MM Use the ground stakes (MM) for ground fixing.Insert the ground stake (MM) into any of the four holes at the bottom of the corner post (D). One corner post (D) one ground stake (MM).
