Specifications

REPAIR OF KÄHRS WOOD FLOORS 
RENOVATION
After extended use, it may be necessary to renovate the
surface treatment and replace it with a new oil treatment. For
very dirty non-stained floors:
1. Clean the floor and make sure that loose particles are
removed.
2. Apply the Kährs Satin Oil to the surface and spread out
evenly and plentifully using a Yarn Mop.
3. Buff the floor with a green disk pad.
4. Remove any excess oil using a rubber squeegee or cloth.
5. Let the surface rest until the oil has dried (about 30 minutes)
6. Buff the floor with a cloth applied on a white disk pad to
remove any excess oil.
Repeat the last step if needed. Please observe that two layers
of thin oil gives a better result than one thick layer. Applying a
too high amount of oil will result in a sticky surface. After a
drying time of 5 hours the floor can be used with care, but
needs 12 hours before lighter furniture can be moved back.
Wait 24 hours to move back carpets and heavier furniture.

Recommended dosage
1 l of Kährs Satin Oil per 40–80 m²
RENOVATION OF FLOORS WITH HEAVY TEXTURE
After extended use, it may be necessary to renovate the
surface treatment and replace it with a new oil treatment.
1. Apply Kährs Cleaner evenly over the surface.
2. Clean the surface using a machine with brush (for example
Orbot Machine with a brush). Please note, do not use too
hard brush. This will prevent damaging of the wood
structure.
3. Dry off the surface using an Absorber Pad or a wet vacuum
machine. This will remove cleaner and dissolved dirt from the
surface.
4. Leave to dry for 30 minutes.
5. Apply Kährs Satin Oil on the surface with a machine (for
example Orbot Machine) using white pad (150–180 rpm)
6. Let the surface rest until the oil has dried (about 30 minutes)
7. Apply a second layer of Kährs Satin Oil on the surface with a
machine (for example Orbot Machine) using white pad (150–
180 rpm)
8. Let the surface rest until the oil has dried (about 30 minutes)
In the case of heavily worn floors, it might be necessary to
repeat step 7 and step 8.
9. Buff the surface with a buffing machine (for example Orbot
Machine) using white pad (150–180 rpm). This is done to
make sure that the oil has been evenly spread.
Please observe that two thin layers of oil give a better result
than one thick layer. Applying too much oil will result in a sticky
surface.
Recommended dosage
1 l of Kährs Satin Oil per 40–80 m²
RENOVATION OF STAINED FLOORS
After extended use, it may be necessary to renovate the
surface treatment and replace it with a new Tinted Satin Oil
treatment.
1. Apply Kährs Cleaner evenly over the surface.
2. Clean the surface using a machine with brush (for example
Orbot Machine with a brush). Please note, do not use an
aggressive hard brush. This will prevent damaging of the
wood structure.
3. Dry off the surface using an Absorber Pad or a wet vacuum
machine. This will remove cleaner and dissolved dirt from the
surface.
4. Leave to dry for 30 minutes.
5. Apply Kährs Stained Satin Oil on the surface with a machine
(for example Orbot Machine) using white pad (150–180 rpm)
6. Let the surface rest until the oil has dried (about 30 minutes)
7. Apply a second layer of Kährs Stained Satin Oil on the
surface with a machine (for example Orbot Machine) using
white pad (150–180 rpm)
8. Let the surface rest until the oil has dried (about 30 minutes)
If a stronger recolouring is needed, repeat step 7 and step 8.
The amount of Stained Satin Oil layers are maximum 3 times,
since too thick layers will result in a sticky surface.
9. Buff the surface with a buffing machine (for example Orbot
Machine) using white pad (150–180 rpm). This is done to
secure that the oil has been evenly spread.
Please observe that two thin layers of oil give a better result
than one thick layer. Applying too much oil will result in a sticky
surface.

Recommended dosage
1 l of Kährs Satin Oil per 40–80 m²
Note! A danger of self-ignition exists in contact with organic
materials (e.g. cotton cloths, saw dust, absorbing insulation
materials etc.) due to self-drying oil content. Rags and other
organic materials soaked in oil have to be put into water
immediately after use, in order to avoid self-ignition.
GENERAL RECOMMENDATIONS ON PARTIAL REPAIR – OILED FLOORS