KA600 FM/AM/SW/LW/WEATHER MUTI-BAND RECEIVER DYNAMO & SOLAR POWER SUPPLY WITH FLASHLIGHT & READING LIGHT TEMPERATURE AND MOISTER INDICATOR OPERATION MANUAL D VOICE SIREN TE ALERT ZZZ NOAA AIR FM AM WB PM COUNTY ALL SINGLE MULTIPLE ENABLE DISABLE %
KEY FEATURES Thank You: Thank you for purchasing the KA 600 muti-band receiver. Please read the manual thoroughly before operating and keep this book in a safe place for future reference. Hope the radio can give you much happiness. FM Band: AM (10K): AM (9K): SW: LW: WEATHER 87.0-108.
INDEX LOCATION OF CONTR........................................ 1 POWER ON AND POWER OFF INDEX SET THE CLOCK.................................................... 20 MOISTER and TEMPERATURE DISPLAY................. 21 Power On and Power Off.................................... 4 USING FLASHLIGHT.............................................. 21 Sleep Timer..................................................... 4 USING READING LIGHT......................................... 21 Alarm On and Alarm Off..........
LOCATION OF CONTROLS LOCATION OF CONTROLS TOP REAR 3 26 25 2 32 4 5 7 6 8 FRONT 27 15 14 13 12 11 9 13 14 24 D VOICE SIREN TE ALERT ZZZ NOAA COUNTY ALL SINGLE MULTIPLE ENABLE DISABLE AIR FM AM WB PM % 23 15 16 16 17 22 18 19 16 17 28 24 29 30 18 19 20 21 Light Light M+/M- Button Speaker Numeric Button Button; Power On:select AM Power Off: select step 9K/10K 7 Button 2 Flash Light Button 8 Button 3 Hand Strap Hole 9 Bu
LOCATION OF CONTROLS POWER ON/POWER OFF LEFT Power On and Power Off Flash Light 1.Rotate the to the valid charging position. ALKALINE. AA Battery Charging ADAPTOR. External Adapter Charging 2.In the unit off mode, press the button to turn on the% unit, press the butto again to turn off the unit.
POWER ON/POWER OFF POWER ON/POWER OFF D Example:Set the ALARM1 on at 8:05, and alarm off after 15 minutes. TE COUNTY ALL SINGLE MULTIPLE ENABLE DISABLE NOTE:If the unit turn on by pressing the button,you can also select the sleep timer by pressing the button shortly to % desired sleep timer. select your 7 A. In the unit off mode, press and hold the button with the icon " 1 " and the hour flashing.
RADIO OPERATION RADIO OPERATION Frequency Diagram Activate and Cancel the Alarm Function In the unit off mode, press the button or shortly with the icon " " flashing in the display, the alarm function is activated. Press the button or again, if the icon " " disappears from the display, the alarm function is canceled.
TUNING INTO STATIONS RADIO OPERATION Select AM Step 9K/10K Auto Scan Tuning In the unit off mode, press and hold the button about 5 seconds with the step 9K or 10K appearing in the display. Press and hold the button again to convert between 9K and 10K. D D % TE TE 05 : 25 1. Turn on the unit and select the band. 2. Press and hold the button or with the frequency changing in the display, then release the button, the unit is auto scan tuning the stations.
T E TUNING IN STATIONS TUNING INTO STATIONS D Auto Tuning Storage (ATS) TE VOICE SIREN ALERT NOAA ZZZ Example1: Input FM 95.80MHz COUNTY ALL SINGLE MULTIPLE ENABLE DISABLE AIR FM AM WB PM % 1. Select the band. 2. Adjust the volume. % 3. Press and hold the < MEMORY > button until frequency starts auto tuning, then release the button, the unit will store the station while scanning the strong signal.
TUNING INTO STATIONS TUNING INTO STATIONS Listening to Preset Stations Manual Tuning Storage (1) Manual Press the button shortly to enter into the memory mode with "M" and the preset memory address flashes, then press the or button shortly to select the preset memory address. 2. Press the button shortly once again to confirm. The station address is stored in the memory. 1. Select the band. 2. Press the or button shortly to select the preset frequency address.
FM RDS FM RDS Delete A Preset Station 1. Select a strong signal station of FM. 2. Press the button shortly with the icon " " in the display. 3. Press the button repeatedly to see what is being transmitted. 1.Select the band. 2.Press the or shortly to select the address where the frequency saved in. 3.Press the button shortly with the icon " " flashing, then press the button shortly again to delete the address.
WEATHER RECEPTION WEATHER RECEPTION Weather Band Channel Frequencies Listening to the Weather Report 1.Press the button shortly to enter into weather reception mode. 2.Rotate the knob to select the local frequency position. Then you can listen to the weather report.
SET THE DATE SET THE CLOCK Adjust the date 1.In the unit off mode, press and hold the button(about 2 seconds) with the year flashes. Then tune the knob to adjust the year, finally press the button to confirm. 2.After setting the year, press the button shortly with the month flashes. Then tune the knob to adjust the month, finally press the button to confirm. 3. After setting the month,you can use the same way to set the date. Example: set 2010.8.
RADIO OPERATION Moister and Temperature Display There is the moister and temperature indicator in the left side of the unit, the upper indicator displays temperature and the downside displays moister. You can press the jack in the battery compartment with the pointy object to convert between the fahrenheit and celsius. Key Lock Function Press and hold the button(about 2 seconds)with the icon " " shows in the display, key lock function is activated.
POWER SUPPLY POWER SUPPLY Ni-MH Battery (1)Remove the battery compartment's cover by pushing the cover in the direction of the arrow. (2)Install the Ni-MH batteries in its compartment, and then connect battery port with the unit. (3)Rotate the to Ni-MH position, the unit can work normally. - + - + + - Ni-MH Batteries AA Batteries (1)Open the battery compartment's cover. (2)Install 3 AA size batteries according to the polarity diagram.
POWER SUPPLY CHARGING Ni-MH BATTERIES Adapter (1)Plug one port of the adapter into the AC socket and plug the other port into the jack. (2)Select the switch to "ADAPTOR" position. If you connect correctly, the icon " " will show in the display. There are four ways to charge the Ni-MH batteries: dynamo charging, solar charging, external adapter charging and PC charging. The "CHARGE" light will be on while dynamo and solar charging.
CHARGING GADGETS CHARGING Ni-MH BATTERIES External Adapter Charging You can charge the Ni-MH batteries either in radio on or off mode. 1.Connect the unit with external adapter correctly then the icon " " shows in the display. 2.The Ni-MH batteries will be charged automatically with the battery power icon " " flows. When the battery power is full, " " stops flowing. Charging MP 3 or Cellphone 1.Push the switch to "OUT" position. 2.
PRECAUTIONS SPECIFICATION Do not expose the radio to rain or humid enviroment. Do not expose the radio to extreme stronge sunlight, close to heat sources, or leave it in the place with excessive dust. When charging the unit by solar, please do not put the unit in the extreme sunlight for long period. If the radio is not used for a long time, remove all the batteries to prevernt battery leakage or corrosion. 1.