PROJECT LONE PINE PROFESSIONAL STUDIO MONITORS LP-6/LP-8 User Manual KALI AUDIO LP-6/LP-8 USER MANUAL 1
Table of Contents Important Safety Information…………………………………….3 About Your Studio Monitor……………………...………………….5 Full Specifications………………………………...………………………7 Inputs and Controls……………………………...………………………8 Boundary EQs and Dip Switches………………...…………….11 First Time Setup……………………………………………...…………...14 Troubleshooting…………………………………………...……………...
Important Safety Information 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Power the product down, and unplug it from power before cleaning. 7. Clean only with a dry cloth. 8. Do not block any ventilation openings. 9. Keep ventilation opening free of dust or other matter. 10. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus.
Important Safety Information 17. Refer all servicing to qualified service personnel. Servicing is required when: A. The apparatus is damaged in any way B. The power supply cord or plug is damaged C. Liquid or other objects have fallen into the product D. The product has been exposed to rain or moisture E. The product does not operate normally F. The product has been dropped 18. This apparatus shall not be exposed to dripping or splashing. 19.
About Your Studio Monitor Congratulations on your Kali Audio LP-Series Studio monitors! These monitors were designed to deliver exceptional accuracy in all sorts of recording, mixing, and production applications. We’re confident that no matter what genre or format you’re working in, you will come to depend on these monitors for their accuracy, reliability, and superior design and construction. Where does “LP” come from? The official name of this product line is “Project Lone Pine.
Features High Performance Woofer The LP-Series uses a woofer with an exceptionally large voice coil and magnet. This allows for greater linearity, resulting in exceptional dynamic range and clarity, as well as extended low end response. All of this is delivered with minimal distortion. Low Noise Port Tube The port tube on the LP-Series was designed to deliver all the benefits of a front-firing port tube, without any drawbacks associated with noise.
Full Specifications LP-6 Powered: Amplifier Class: Power Configuration: LF Power: HF Power: Total Power: LF Driver: HF Driver: Freq.
Inputs and Controls KALI AUDIO LP-6/LP-8 USER MANUAL 8
Inputs and Controls Dip Switch Quick Reference Guide The quick reference guide on the back of the speaker can help you set the dip switches to the appropriate positions for your application without needing to consult this manual. Dip Switches The dip switches control Boundary EQ, HF and LF Trim, and power to the RCA input. A full explanation of the operation of the dip switches can be found on page 11.
Inputs and Controls Volume Control The volume control allows users to adjust the output of the speaker from -∞ to +6 dB. There is a center detente at the +0 dB setting, and this is where Kali recommends you leave the volume setting, adjusting the level instead from your device. Two notable exceptions to this recommendation are: 1. If you are working in an asymmetrical room, it may be necessary to have one monitor louder than the other to achieve balance. 2.
Boundary EQs & Dip Switches One of the most innovative features of the LP-Series monitors are the boundary compensation EQs. These EQs were made to compensate for low frequency interactions that the speakers will have with various surfaces in many common placements. Each set of dip switches controls one aspect of the speakers performance, independent of the other switches. Switches 1-3 control the boundary compensation EQs. Switches 4 and 5 control the LF trim. Switches 6 and 7 control the HF trim.
Boundary EQs & Dip Switches Switches 1-3: Boundary Compensation EQs Position 4: Meter Bridge The speaker is on a meter bridge or console bridge Switch 1: UP Switch 2: UP Switch 3: DOWN Position 5: On a Desk, Away from Walls The speaker is on a desk or table, and is at least .5 meters (20 inches) away from any walls. Switch 1: DOWN Switch 2: DOWN Switch 3: UP Position 6: On a Desk, Close to a Wall The speaker is on a desk or table, and is within .
Boundary EQs & Dip Switches Switches 4 & 5: Low Frequency Trim The High Frequency trim will add or subtract 2 dB from the High Frequency response of the speaker. This can be done as a matter of personal taste, or if the room you’re mixing in requires additional adjustment beyond what is offered by the boundary compensation EQs. Switch 4: Engage LF Trim • DOWN: LF Trim Disengaged • UP: LF Trim Engaged Switch 5: Adjust LF Trim: Note: Switch 5 does not function independent of switch 4.
First Time Setup •Before you plug the speaker in, make sure that the power switch is in the OFF position •Plug the speaker in •Connect audio cables If you’re connecting RCA, make sure that dip switch #8 is switched UP to the ON position If you’re connecting XLR or TRS, make sure that dup switch #8 is switched DOWN to the OFF position •Turn the volume knob counter clockwise as far as it will go •Turn the speaker on •Start playing material from your playback device at a low volume •Slowly turn the volume kn
Troubleshooting 1. I opened the speaker, and it is damaged. If you received a speaker that is obviously damaged, please contact your dealer immediately. 2. The speakers are making no sound • Is the speaker plugged in? • Is the speaker turned on? There should be a blue LED on the front of the speaker if it’s on. If this light is off, the speaker is turned off.
Limited Warranty What does this warranty cover? This warranty covers defects in materials or workmanship for a period of one year (365 days) after the purchase date of the product. What will Kali do? If your product is defective (materials or workmanship,) Kali will replace or repair the product at our discretion - free of charge. How do you initiate a warranty claim? Contact the retailer from whom you bought the product to initiate a warranty process.