Installation Guide

ManualsBrandsKallista ManualsPlumbingOne Lever Handle Thermostatic Valve Trim with Cold and Hot Indexing - Less Rough In

INSTALLATION INSTRUCTIONS

Thermostatic Valve Trim

1048650-2-K

1 of 6

Questions? Problems? For additional assistance, please contact KALLISTA’s Customer

Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.

P23052-CR, P23052-LV, P23122-LV,

P23222-RK, P23222-LV, P24022-CL,

P24022-CR, P24022-KL, P24022-RB,

P24022-RL, P24122-CR, P24122-LV,

P24129-CR, P24129-LV, P24421-CR,

P24421-LV, P24422-CR, P24422-LV,

P24522-LV, P24522-TT, P24622-CR,

P24622-LV, P24722-LV

Summary of content (6 pages)

PAGE 1
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS P23052-CR, P23052-LV, P23122-LV, P23222-RK, P23222-LV, P24022-CL, P24022-CR, P24022-KL, P24022-RB, P24022-RL, P24122-CR, P24122-LV, P24129-CR, P24129-LV, P24421-CR, P24421-LV, P24422-CR, P24422-LV, P24522-LV, P24522-TT, P24622-CR, P24622-LV, P24722-LV 1048650-2-K 1 of 6 KALLISTA ©2014 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
PAGE 2
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If you encounter any installation or performance problems, please do not hesitate to contact us at the phone number listed at the bottom of the page. BEFORE YOU BEGIN Please read all instructions before you begin.
PAGE 3
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS 1. INSTALL THE VALVE STEM ADAPTER Select the correct valve stem adapter and screw. Spline Adapter Valve Stem Adapter NOTE: Check the finished wall surface as related to the graphics on the plaster guard.  Select the correct length valve stem adapter and screw for your application. Refer to the information stamped on the plaster guard to verify the wall thickness.
PAGE 4
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS 2. ADJUST THE HANDLE ASSEMBLY Spline Adapter Valve Stem Adapter Handle Assembly  Ensure the valve stem adapter is lightly placed over the spline adapter.  Place the handle assembly over the valve stem adapter.  Turn the handle clockwise until the stop is contacted. The valve will be in the full cold position. The handle should be between 9 and 10 o’clock positions. To adjust the position of the handle, refer to the alignment instructions below.
PAGE 5
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS 3. INSTALL THE FRONT PLATE Verify the seal covers the wall opening. Stud Nut 7/16" (11 mm) MAX Screw Valve Stem Adapter  Ensure the valve stem adapter is firmly pressed onto the valve stem.  Secure the valve stem adapter to the valve with the correct length screw, as selected in the “Install the Valve Stem Adapter” section of this guide.  Thread the two studs into the threaded holes of the valve.  Place the front plate assembly over the studs.
PAGE 6
Thermostatic Valve Trim INSTALLATION INSTRUCTIONS 4. INSTALL THE TRIM All other Trim P24722-LV Trim Escutcheon Adapter Ring Front of Adapter Ring Escutcheon Setscrew NOTE: If installing the P24722-LV trim, proceed to the “For P24722-LV” section below.  Place the escutcheon on the wall with the drain notch located downward in the 6 o’clock position.  Thread the handle assembly onto the hub of the front plate assembly to secure the escutcheon in place.