Installation Sheet

ManualsBrandsKallista ManualsBathroom FaucetsOne 1.2 GPM Widespread Bathroom Faucet with Nero Marquina Lever Handles

INSTALLATION INSTRUCTIONS

Lavatory Faucet

1223783-2-F

1 of 7

Questions? Problems? For additional assistance, please contact KALLISTA’s Customer

Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.

P24490-CR, P24490-LV, P24491-CR,

P24491-LV, P24492-CR, P24492-LV,

P24700, P24705, P24706, P24736, P24800

Summary of content (7 pages)

PAGE 1
Lavatory Faucet INSTALLATION INSTRUCTIONS P24490-CR, P24490-LV, P24491-CR, P24491-LV, P24492-CR, P24492-LV, P24700, P24705, P24706, P24736, P24800 1223783-2-F 1 of 7 KALLISTA ©2018 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4-KALLISTA (1-888-452-5547) or kallista.com.
PAGE 2
Lavatory Faucet INSTALLATION INSTRUCTIONS THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If you encounter any installation or performance problems, please do not hesitate to contact us at the phone number listed at the bottom of the page. IMPORTANT INFORMATION Before installation, unpack the new faucet and inspect it for damage.
PAGE 3
Lavatory Faucet INSTALLATION INSTRUCTIONS 1. INSTALL THE SPOUT Gasket Trim O-Ring Trim Spout Shank O-Ring Seal Gasket Washer Nut Nylon Washer Rubber Screen Gasket Tee Assembly Install the Spout Remove the tee assembly, nut, and washer from the spout shank. Ensure that the seal gasket or O-ring is installed to the underside of the spout. Fit the spout shank through the top of the lavatory. Install the washer and nut onto the spout shank. Tighten the nut with a wrench to secure.
PAGE 4
Lavatory Faucet INSTALLATION INSTRUCTIONS 2. INSTALL THE HANDLES P24800 DO NOT apply silicone sealant in this groove. All Other Trim Seal Gasket P24706 Trim O-Ring Washer Apply 100% silicone sealant to the underside of escutcheon. Apply 100% silicone sealant in this area only. Install the Handle Assemblies Ensure that the seal gasket or O-ring is installed to the underside of each of the handle assemblies. For P24706: Apply a bead of 100% silicone sealant to the underside of the escutcheon.
PAGE 5
Lavatory Faucet INSTALLATION INSTRUCTIONS 3. CONNECT THE HOSES Valve Valve Hose Hose Thread the male ends of the hoses into the valves. Do not overtighten! Thread the female ends of the hoses onto the tee. 4. INSTALL THE DRAIN Flange Stopper Apply plumbers putty. Gasket Washer Apply thread sealant. Nut Tailpiece Drain Body Disassemble the stopper and flange from the drain body. Apply a small bead of putty or sealant to the bottom of the flange.
PAGE 6
Lavatory Faucet INSTALLATION INSTRUCTIONS 5. COMPLETE THE CONNECTIONS Supply Hoses (Not Provided) Cold Hot Install the lavatory according to the lavatory manufacturer’s instructions. Connect the supply hoses (not provided) to the supply stops (left is hot; right is cold). Tighten all connections with an adjustable wrench. 6. COMPLETE THE INSTALLATION Aerator Key Connect the P-trap (not supplied) to the tailpiece. Ensure that all connections are watertight.
PAGE 7
Lavatory Faucet INSTALLATION INSTRUCTIONS 7. ADJUST THE HANDLE AND ESCUTCHEON ALIGNMENT Screw Handle Spline Adapter Bearing Loosen screws. Tighten screws. Pull up to remove the handle and bearing from the escutcheon. NOTE: Use a pick or a similar tool to help remove the spline adapter. To adjust the handle, remove the screw and reposition the spline adapter. Reinstall the screw. Ensure that the valve is fully turned to the OFF position.