Toilet INSTALLATION INSTRUCTIONS P70310 1142313_2_B 1 of 9 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Toilet INSTALLATION INSTRUCTIONS Thank You For Choosing KALLISTA We appreciate your commitment to KALLISTA quality products. Please take a moment to review this manual before you install your KALLISTA product. If you encounter any installation or performance problems, please do not hesitate to contact us at the phone number listed at the bottom of the page. Important Information CAUTION: Risk of personal injury. If the new toilet is not installed immediately, temporarily place a rag in the closet flange.
Toilet INSTALLATION INSTRUCTIONS Installation 1. Install or relocate the supply and outlet as necessary to conform to the roughing-in dimensions. 14-3/16" (360 mm) 11-5/8" (295 mm) 16-3/16" (411 mm) 3/8" NPT Supply 34" (864 mm) 11-13/16" (300 mm) old wax. 12" (305 mm) Minimum Rough-in 7-1/2" (191 mm) 8-1/2" (216 mm) 2. If replacing a toilet, remove the 6-5/8" (168 mm) 11" (279 mm) 3. Ø 3/8" Mounting Holes 4. Tape in place and drill holes. Template 3/8” Mark here with tape. 5.
Toilet INSTALLATION INSTRUCTIONS Installation 8. 7. 9. Confirm correct alignment between toilet hole and bracket. 11. Slide nut onto the supply hose, with flared end last and run hose through toilet wall. 10. 12. Hose Guide 1142313_2_B 4 of 9 Questions? Problems? For additional assistance, please contact KALLISTA’s Customer Service Department at 1-888-4KALLISTA (1-888-452-5547) or FAX 1-888-272-3094.
Toilet INSTALLATION INSTRUCTIONS Installation 13. 14. Note the position of the colored buttons for reinstallation. Buttons Metal Washer Rubber Washer 15. Squeeze the tabs and pull 16. Thread the bolts into the bowl 17. Reinstall the canister so it snaps into 18. Rotate the canister so that the 19. Mark hole location, drill 3/16″ pilot 20. straight up on the canister. colored buttons are in their original positions. through the bolt holes in the bottom of the tank.
Toilet INSTALLATION INSTRUCTIONS Installation 22. Apply weight evenly. 21. Carefully tilt backward Do not move after placement! Watertight seal may be broken! until trapway and outlet touch. 23. Carefully thread the screws into the brackets, until toilet is secure. Alternately tighten left and right sides to prevent pulling the toilet off center. Install cap to cover screw. Do not overtighten. 24. Caulk around base. Caulk 25. Connect supply and turn on the water.
Toilet INSTALLATION INSTRUCTIONS Installation 26. Flush several times and check for leaks. 27. Turn here to adjust the water level. 28. Install the tank lid and the seat. Flush the toilet and check for proper flush. If necessary, loosen the lock nuts and adjust the flush rod lengths as described in the troubleshooting section. Waterline 29. Periodically check for leaks for several days following the installation.
Toilet INSTALLATION INSTRUCTIONS Troubleshooting Guide SYMPTOMS 1. Poor flush. A. B. C. D. E. Recommended Action Adjust the tank water level to match the waterline. Fully open the water supply shut-off valve. Clear obstructions from the trapway, jet, or bowl rim holes. Clear obstructions in the soil pipe or vent pipe. Remove the tank lid, loosen the locknuts on the push button assembly and unscrew the push button rods slightly to lengthen them. Replace the tank lid and flush.
Toilet INSTALLATION INSTRUCTIONS Service Parts 1111827 Tank Accessory Pack P70314-00-** Push Button Assembly 1081365** Floor Mountng Kit (2 ea.) 1042615** Hold Down Kit (2 ea.
