Ceramic Heater Instruction Booklet KCE520 KCE520_IB_FA.
Important Please retain your instruction book for future use. In the event that you need some assistance with your Kambrook appliance, please contact our Customer Service Department on 1300 139 798 (Australia) or 09 271 3980 (New Zealand). Alternatively, visit us on our website at www.kambrook.com.au KCE520_IB_FA.
Contents Kambrook Recommends Safety First p4 Your Ceramic Heater p6 Quick Start Guide p7 Using Your Ceramic Heater p8 Care and Cleaning p11 Warranty Details p12 KCE520_IB_FA.
Kambrook Recommends Safety First IMPORTANT: Please retain your instruction book for future use. At Kambrook, we believe that safe performance is the first priority in any consumer product, so that you, our valued customer can confidently use and trust our products. We ask that any electrical appliance that you use be operated in a sensible fashion with due care and attention placed on the following important operating instructions.
• Do not allow materials that have been in contact with oil, petroleum based products or drying fluids to come in contact with the heater. • Do not run the cord under carpeting or cover the cord with rugs, runners or the like. Arrange cord away from traffic areas and where it will not be tripped over. • To disconnect heater turn the power to OFF, then turn the control switch to off. Turn off at the power outlet then remove the plug from its outlet.
Your Ceramic Heater 1. 2. 3. 1800 watt ceramic heating element for efficient heating LCD screen ThermoGuard protection for peace of mind 6. 7. Control Panel 4. 5. Convenient 8hr auto-off timer 2 heat setting, plus auto mode and fan only setting 8.
Quick Start Guide Setting the heating mode Turning the heater on Plug the cord into a 230V or 240V power point and switch on. Switch on the unit using the ON/OFF switch. Setting the variable temperature Press the MODE button to select AUTO setting. Press the VARIABLE TEMPERATURE button to increase the temperature or press the VARIABLE TEMPERATURE button to decrease the temperature. Press the POWER/SWING button to activate The heater will start operating at the LOW heat setting.
Using Your Ceramic Heater Before First Use Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on.
Setting the Variable Temperature The variable temperature can be used to maintain your desired temperature. NOTE: The variable temperature only operates when the heater is being used in the Auto mode. button until the Press the MODE heater is set to AUTO mode. The LCD screen will display the default temperature of 25°C and will flash. When the temperature is flashing, you may set the desired temperature pressing the VARIABLE TEMPERATURE buttons on the control panel.
Using Your Ceramic Tower Heater continued ThermoGuard Overheating Safety Device Your heater is fitted with a safety device that switches off the heater in the event of overheating. Should this heater stop working, turn off the heater and inspect the air inlet and outlet for blockages. Wait for the heater to cool for the protection system to reset before attempting to restart the heater. 10 KCE520_IB_FA.
Care and Cleaning Ensure that the heater is switched off and disconnected from the power point before cleaning. Use a clean, dry cloth to clean the external surfaces of the heater. If the heater has collected dust or dirt inside the unit or around the elements, have the unit cleaned by a qualified service agent. Do not operate the heater in this condition. Do not attempt to open the case of the heater at any time as there are no customer serviceable parts inside.
Kambrook 12 Month Replacement Warranty The Kambrook Replacement Warranty does not apply to any defect, deterioration, loss, injury or damage occasioned by, or as a result of, misuse or abuse, negligent handling or if the product has been used other than in accordance with the instructions. The Kambrook Replacement Warranty excludes breakables such as glass and ceramic items, consumable items and normal wear and In New Zealand, this Kambrook Replacement Warranty does not affect your mandatory statutory tear.