Manualshelf

User Guide

ManualsBrandsKAPSCH TRAFFICCOM CANADA ManualsElectronicsRFM-S Transmitter
12
Page 2 of 2
©
©
M
M
A
A
R
R
K
K
I
I
V
V
I
I
N
N
D
D
U
U
S
S
T
T
R
R
I
I
E
E
S
S
C
C
o
o
r
r
p
p
.
.
E
E
X
X
C
C
E
E
P
P
T
T
A
A
S
S
M
M
A
A
Y
Y
B
B
E
E
O
O
T
T
H
H
E
E
R
R
W
W
I
I
S
S
E
E
P
P
R
R
O
O
V
V
I
I
D
D
E
E
D
D
B
B
Y
Y
C
C
O
O
N
N
T
T
R
R
A
A
C
C
T
T
,
,
T
T
H
H
E
E
S
S
E
E
D
D
R
R
A
A
W
W
I
I
N
N
G
G
S
S
A
A
N
N
D
D
S
S
P
P
E
E
C
C
I
I
F
F
I
I
C
C
A
A
T
T
I
I
O
O
N
N
S
S
C
C
O
O
N
N
T
T
A
A
I
I
N
N
P
P
R
R
O
O
P
P
R
R
I
I
E
E
T
T
A
A
R
R
Y
Y
I
I
N
N
F
F
O
O
R
R
M
M
A
A
T
T
I
I
O
O
N
N
A
A
N
N
D
D
A
A
R
R
E
E
T
T
H
H
E
E
P
P
R
R
O
O
P
P
E
E
R
R
T
T
Y
Y
O
O
F
F
M
M
A
A
R
R
K
K
I
I
V
V
I
I
N
N
D
D
U
U
S
S
T
T
R
R
I
I
E
E
S
S
L
L
T
T
D
D
.
.
A
A
N
N
D
D
A
A
R
R
E
E
I
I
S
S
S
S
U
U
E
E
D
D
I
I
N
N
S
S
T
T
R
R
I
I
C
C
T
T
C
C
O
O
N
N
F
F
I
I
D
D
E
E
N
N
C
C
E
E
A
A
N
N
D
D
S
S
H
H
A
A
L
L
L
L
N
N
O
O
T
T
B
B
E
E
T
T
R
R
A
A
N
N
S
S
M
M
I
I
T
T
T
T
E
E
D
D
O
O
R
R
R
R
E
E
P
P
R
R
O
O
D
D
U
U
C
C
E
E
D
D
O
O
R
R
C
C
O
O
P
P
I
I
E
E
D
D
O
O
R
R
U
U
S
S
E
E
D
D
A
A
S
S
T
T
H
H
E
E
B
B
A
A
S
S
I
I
S
S
F
F
O
O
R
R
M
M
A
A
N
N
U
U
F
F
A
A
C
C
T
T
U
U
R
R
E
E
O
O
R
R
S
S
A
A
L
L
E
E
O
O
F
F
A
A
P
P
P
P
A
A
R
R
A
A
T
T
U
U
S
S
W
W
I
I
T
T
H
H
O
O
U
U
T
T
P
P
R
R
I
I
O
O
R
R
W
W
R
R
I
I
T
T
T
T
E
E
N
N
P
P
E
E
R
R
M
M
I
I
S
S
S
S
I
I
O
O
N
N
.
.
D. Procedure to test and activate RFM-S:
In idle mode the reader generates NO RF. (RFM-S transmitter light off).
To turn on the RFM-S transmitter do the following:
1) Set the iteration count to a large number ( IC 1000 )
2) Issue a read transponder command ( RT )
The iteration count is the number of 20 microsecond trigger pulses the reader will issue
for every RT command.
for ic=1000 the reader will transmit for about 6-7 seconds.
for ic=2000 the time is around 13 seconds.
Max is 32767
Ignore all other commands.
E. Example:
ic 1000 //user input
IC=1000 //reader confirms
rt //user input
READ ERROR //after 1000 trigger pulses (about 6 secs later) reader
//responds with "READ ERROR" since (we assume) no transponder
//has been read.
(The iteration count is persistent. It remains the same unless changed or the reader is reset).
F. Warning Statement:
This device complies with Part 90 of the FCC Rules. Modifications not expressly
approved by the manufacturer may invalidate the user’s authority to operate the equipment