Operating instructions
Table Of Contents
- T 300 T-Racer
- Deck and Driveway Cleaner
- Safety instructions
- m WARNING
- When using this product basic precautions should always be followed, including the following:
- Read all the instructions before using the product.
- Please observe the safety instructions of your pressure washer.
- The T-Racer must not be used by children.
- Only trigger the gun of the pressure washer if the T-Racer is located on the surface to be cleaned.
- Keep all persons/animals clear of the immediate vicinity of the cleaning head.
- Beware of the recoil force! Ensure a stable position and firmly hold the trigger gun with the extension handle.
- Turn off the pressure washer when examing or changing the T-Racer and after the completion of the cleaning operation.
- Maximum water temperature allowed is 140 °F (60°C). Please follow the instructions of your pressure washer.
- n CAUTION
- Do not use on windows.
- The T-Racer is not suited for scouring or scrubbing.
- Do not run over freestanding corners.
- Always test the T–Racer in an inconspicuous area.
- Never operate in the same area for more than 2 seconds, damage may occur.
- Guide the T-Racer over the surface without effort.
- SAVE THESE INSTRUCTIONS!
- Preparing the Appliance
- Description of the Appliance
- When unpacking the product, make sure that no accessories are missing and that none of the package contents have been damaged. If you detect any transport damages please contact your retailer.
- Illustration
- 1 Housing
- 2 Handle
- 3 Twist grip Power (for adjustment of the cleaning pressure)
- 4 Bayonet connection with union nut
- 5 Lower wand (green)
- 6 Upper wand (yellow)
- 7 Rotating nozzle holder
- 8 Purple high-pressure nozzles (2x)
- 9 Green high-pressure nozzles (2x)
- Intended use
- This T-Racer can be used with all Kärcher electric pressure washers up to 2000 psi.
- Use on horizontal surfaces like driveways, patios, side walks, etc.
- The T-Racer has not been designed for commercial use.
- Symbols on the appliance
- m DANGER
- Keep hands away from moving parts.
- HARD
- For sturdy surfaces (e.g. tiles, concrete, stone).
- SOFT
- For sensitive surfaces (e.g. wood).
- Preparing the Appliance
- Selection of the nozzles
- You need to use the matching nozzles to ensure that your pressure washer works properly.
- Note:
- Delivery rate (l/min): See operating instructions or type plate of your pressure washer.
- Pressure washer with delivery rate of less than 5.8 l/min (350 l/h)
- e.g.: K 2 – K 3
- Use green nozzles.
- Note:To ensure a trouble free operation of your pressure washer, you must replace the two violet nozzles with the green nozzles.
- Pressure washer with delivery rate from 5.8 l/min (351 l/h) to 7.5 l/min (450 l/h)
- e.g.: K 3 – K 5
- Use violet nozzles.
- Note: The violet nozzles are premounted.
- Replacement of nozzles
- Illustration
- a
- Remove the clip.
- b
- Pull out the violet nozzle.
- c
- Insert the green nozzle.
- d
- Re-insert the clip.
- Application
- Note: Always use Kärcher water filter (order no. 4.730-059.0) during suction operations of the pressure washer.
- Cleaning horizontal surfaces
- Note: Outdoor surfaces should be swept before the T-Racer is used to avoid damaging the nozzles.
- Connect the T-Racer and both wands with the trigger gun.
- Illustration
- Connect lower wand (green) with T- Racer.
- 1 Press the bayonet connection into the bayonet catch, then turn by 90° until it locks into place.
- 2 Tighten the union nut.
- Connect upper wand (yellow) with lower wand (green).
- 1 Press the bayonet connection into the bayonet catch, then turn by 90° until it locks into place.
- 2 Tighten the union nut.
- Connect trigger gun with upper wand (yellow).
- 1 Press the bayonet connection into the bayonet catch, then turn by 90° until it locks into place.
- 2 Tighten the union nut.
- Illustration
- n CAUTION
- Do not run over freestanding corners.
- Adjust the twist grip "Power" in accordance with the cleaning surface.
- Do not reach under the edge of the T- Racer while the device is in operation.
- Control elements
- The cleaning pressure is adjusted with the twist grip Power via a bypass system.
- Robust surfaces (for e.g. tiles, concrete, stone)
- Illustration
- Set twist grip Power to "HARD".
- For the effective cleaning of hard-to- remove contamination.
- Sensitive surfaces (for e.g. wood)
- Illustration
- Set twist grip Power to "SOFT".
- For the gentle cleaning of sensitive surfaces.
- Troubleshooting
- Pressure washer does not build up the pressure or is vibrating.
- Dismantle the nozzles, check the nozzles for damage, rinse the T-Racer with clean water then reinstall the nozzles.
- You need to use the matching nozzles to ensure that your pressure washer works properly.
- Select and install the required high- pressure nozzles in accordance with the high-pressure cleaner used.
- General notes
- Tip
- You can use the wands with any other Kärcher accessory.
- Maintenance and care
- Maintenance
- The unit is maintenance-free.
- Care
- Use a moist cloth and clean the appliance after use.
- Store the appliance in a frost free area.
- The device can be suspended into the KÄRCHER organizer for storage.
- Customer Support USA and Canada
- In the U.S. or Canada, please call 1-800-537-4129 for warranty issues and visit www.karcher-help.com for technical support and product assistance.
- Customer Support Mexico
- Call: 01-800-024-13-13 for help or visit our website: www.karcher.com.mx
- Français
- Español
AVERTISSEMENT
En utilisant ce produit, toujours observer
une certaine prudence élémentaire, in-
cluant notamment :
Lire toutes les instructions de service
avant d'utiliser l'appareil.
Observez les consignes de sécurité
de votre nettoyeur haute pression.
Le T-Racer ne doit jamais être utilisé
par des enfants.
Déclencher le jet haute pression sur
le pistolet haute pression unique-
ment lorsque le T-Racer se trouve
sur la surface à nettoyer.
Aucune autre personne ne doit se
trouver à proximité de la tête de net-
toyage.
Attention au recul ! Assurer une
bonne stabilité et bien tenir le pistolet
haute pression avec la rallonge ou la
poignée.
Mettre le nettoyeur haute pression
hors service à la fin du nettoyage.
Lors du travail sur le T-Racer, sépa-
rer de plus celui-ci du pistolet haute
pression.
Température d’eau maximale 60 °C
(observer les instructions de votre
nettoyeur haute pression).
몇 PRÉCAUTION
Ne convient pas pour le nettoyage
des fenêtres.
Le T-Racer n’est pas approprié pour
récurer ou frotter !
Ne pas passer sur des coins en saillie!
Toujours tester préalablement dans
des zones discrètes.
Ne jamais actionner le T-Racer plus
de 2 secondes au même endroit
sous peine d'endommagement.
Déplacer le T-Racer sans déploie-
ment de force sur la surface.
CONSERVER CES INSTRUCTIONS !
Contrôler le matériel lors du déballage
pour constater des accessoires man-
quants ou des dommages. Si des dé-
gâts dus au transport sont constatés, il
faut en informer le revendeur.
Illustration
1 Boîtier
2 Poignée
3 Poignée rotative Power (pour ajuster
la pression de nettoyage)
4 Raccord baïonnette avec douille de
sécurité
5 Paroi inférieure (vert)
6 Tube de rallonge supérieur
7 Porte-buse rotatif
8 Buses haute pression violettes (2
pièces)
9 Buses haute pression vertes (2
pièces)
Le T-Racer peut être utilisé avec tous
les nettoyeurs haute pression Kärcher
jusqu’à une pression de 2000 psi.
A utiliser sur des surfaces horizontales
telles que des allées, des terrasses, des
trottoirs, etc.
Le T-Racer ne convient pas à une utili-
sation industrielle.
DANGER
Lors du fonctionnement, ne pas
mettre la main sous le bord du
T-Racer !
HARD
Pour surfaces robustes (par ex.
carrelage, béton, pierre).
SOFT
Pour surfaces sensibles
(par ex. bois).
Consignes de sécurité Préparation
Description de l’appareil
Utilisation conforme
Symboles sur l'appareil
7FR