Operating instructions

English 11
speed and water volume are increased when the
boost function is activated. The Boost function can
be activated at cleaning level 1 and cleaning level 2.
The indicator for the corresponding cleaning level
flashes when the Boost function is activated. Allow
the device to slide slowly over the floor without ex-
erting any pressure on the device.
Illustration K
 Various different rollers are available, depending on
the scope of delivery. The colour of the rollers indi-
cates the respective special application for which
they are suitable.
– Grey / yellow universal rollers: versatile
– Rollers with black stripes: For cleaning insensitive
hard floors (e.g. stone, ceramic); not suitable for sen-
sitive natural stone floors (e.g. marble, terracotta)
Note
For an optimum cleaning result, wash the rollers in the
washing machine at 60° C before initial use.
Starting work
ATTENTION
Uncontrolled motion
Damage to the device and material damage
The cleaning rollers start rotating as soon as the device
is switched on.
Hold the handle tight to prevent the device from moving
away independently.
ATTENTION
Fresh water tank or waste water tank not installed
Material damage
Before starting cleaning work, ensure that the fresh wa-
ter tank is filled with water and the waste water tank is
fitted in the device.
1. Press the ON/OFF switch.
Illustration I
The device switches on.
The cleaning level 1 indicator for normal roller
speed and normal water quantity is lit.
2. Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
3. If necessary, switch to cleaning level 2 using the but-
ton for adjusting the cleaning level.
Illustration J
This increases the roller speed and water volume.
The Cleaning level 2 indicator lights up.
Note
Selection of cleaning level 1 or cleaning level 2 de-
pends on the type of floor to be cleaned (e.g. wooden or
stone floor).
The device is set to cleaning level 1 after initial start-up.
The cleaning level setting last used always remains ac-
tivated after interrupting and resuming work.
4. If necessary, activate the boost function for cleaning
stubborn dirt (see also Chapter General notes on
operation).
Illustration K
Battery run time
The "Battery" indicator shows the remaining battery run
time:
 3 LEDs illuminated - 3/3 (full) battery run time
 2 LEDs illuminated - 2/3 battery run time
 1 LED illuminated - 1/3 battery run time
Illustration N
Acoustic or optical signals warn of a flat battery.
 An acoustic signal sounds 2 times and the lowest
LED flashes approx. 5 minutes before the battery is
empty.
 An acoustic signal sounds 2 times and the lowest
LED continues to flash approx. 1.5 minutes before
the battery is empty.
 The last LED flashes quicker for 60 seconds when
the battery is empty and the device has switched off.
Emptying the waste water tank
 The "MAX" indicator (red) lights up and an acoustic
signal sounds when the waste water tank is full.
Illustration M
 After 60 seconds, an acoustic signal sounds again
and the device switches off.
 The "MAX" indicator (red) flashes for 10 seconds
once the device is switched off.
 As long as the waste water tank is full and the (red)
“MAX” display lights up, the process restarts and the
following two steps are repeated:
a The device can be switched on again.
b The device runs for another 60 seconds and then
switches off again.
1. Press the ON/OFF switch.
The device switches off.
2. Press the unlocking button for the waste water tank
with your foot and lift the device.
Illustration O
The waste water tank releases from the device.
3. For draining, do not transport the waste water tank
by the top cover, but horizontally with both hands at
the narrow sides.
4. Empty the waste water tank through the opening in
the cap. In the case of adhering dirt deposits, re-
move the cover of the waste water tank and rinse
the waste water tank with tap water.
5. Fit the waste water tank (see Chapter Fitting the
waste water tank).
Refilling with detergent
 The "MIN" indicator (blue) lights up and an acoustic
signal sounds when the fresh water tank is empty.
Illustration L
 The acoustic signal sounds once a minute as a re-
minder.
1. Fill the fresh water tank (see Chapter Filling the
fresh water tank).
Interrupting operation
ATTENTION
Damp rollers
Moisture damage to sensitive floors
To prevent damage to sensitive floors through wet roll-
ers, place the device in the parking station during longer
work breaks.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Note
If the device is placed on the parking station without a
waste water tank, the unlocking button must be pressed
to remove the device.
Illustration AF
Ending operation
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AB