Owner's manual

- 2
 Switch off the plant, turn the pro-
gramme selection switch at the operat-
ing panel to "STOP".
The following washing programs are avail-
able:
Stop
Interrupts the programme.
Basic position, washing tools in the tool
holders.
-Note
STOP function is active in all switch posi-
tions without washing programme.
High-pressure wash
Removes coarse dirt.
Warm water with shampoo
Distance of high pressure nozzle approx 30
cm.
Foam Wash
Deep cleaning with active foam.
Only use foam brush when the programme
is running and after the high-pressure
wash.
Rinse
Rinse off shampoo and foam.
Distance of high pressure nozzle approx 50
cm.
Hot wax
Warm water with paint protection.
Use after rinsing.
Distance of high pressure nozzle approx 80
cm.
Top care
For Spot-free drying.
Demineralised water leaves a spot-free
high gloss finish.
Distance of high pressure nozzle approx 80
cm.
Dirt Loosening
Removes persistent dirt.
Warm water with special detergent.
Distance of high pressure nozzle approx 30
cm.
Micro Emulsion
Removes persistent dirt.
Warm water with special detergent.
Distance of high pressure nozzle approx 30
cm.
Insects Loosening
Loosens insects.
Warm water with special insect removing
detergent.
Distance of high pressure nozzle approx 30
cm.
Wheel Cleaning
Loosens brake dust.
Water with special detergent.
Max. soak time 2 minutes.
Application before the car wash and only
on coated or painted wheels.
Under-chassis Wash
Removing coarse dirt from the underchas-
sis.
Washing cycle begins with a delay of ap-
prox. 10 seconds; drive the vehicle back-
wards and forwards over the under-chassis
wash.
 Turn the program selection switch to
the desired cleaning program.
 Inserting a certain number of tokens or
coins into the coin mechanism.
– An invalid coin can be returned by
pressing the push button and removed
from the return slot.
– The remaining value display shows the
remaining time until the paid washing
time elapses.
If the orifice of the banknote reader is illumi-
nated, the reader is ready for use.
 Insert the banknote in the banknote
reader.
– The remaining value display shows the
remaining time until the paid washing
time elapses.
 Turn the programme selection switch at
the operating panel to "STOP". The
washing time will continue!
 Unlock the lock.
 Pull the coin tray out to the side to re-
move the coin container.
 Unlock the lock of the front plate.
 Pull the locking mechanism down and
open the front plate.
 Remove and empty the coin box.
 Put the coin box back.
 Close the front plate.
Note:
The front plate can be closed more easily,
if the locking mechanism is pulled down at
the same time.
 Lock the lock of the front plate.
If the operating time lock (setting in the
main switch cabinet) is activated, the coin
slot and the acceptance of banknotes (op-
tion) is locked. The red LED is on.
The remote control is taken out of operation
when the main switch is switched off at the
main switch cabinet.
The bases of a safe operating of the equip-
ment is thr regularly maintenance accord-
ing to the following maintenance plan.
Use only original parts of the manufacturer
or part suggessted by him, such as
– replacement and wear parts
– Accessory parts
Operation
Switch-off in case of emergency
Washing programmes
Standard programmes
Additional programmes (option)
Programm selection
Programme start
Start by inserting coins
Start by inserting a banknote (option)
Programme abortion
Emptying the coins container
Remote control
Multifunction unit
Operating time lock
Shutting down
Technical specifications
Remote control Multifunction unit
Control
Voltage VDC 24
Coin acceptor
Voltage VDC 12
Banknote reader (option)
Heating VAC - 24
Banknote read-
er
VDC - 12
Dimensions
Width mm 440 1010
Height mm 525 3270
Depth mm 210 355
Maintenance and care
Maintenance instructions
9EN