B 80 W Bp R e w gis w w. te ka r a er n ch d er .
http://www.kaercher.
Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners. Contents Safety instructions . . . . . . . Function . . . . . . . . . . . . . . . Proper use . . . . . . . . . . . . . Environmental protection . . Warranty . . . . . . . . . . . . . . . Operating and Functional Elements . . . . . . . . . . . . . . . . . Before Startup. . . . . . . . . . . Operation . . . . . . . . . . . . . .
Operating and Functional Elements Illustration of scrubbing vacuum 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Parking brake Rotary handle to incline the vacuum bar Height adjustment of suction bar Wing nuts for fastening the vacuum bar Suction hose Vacuum bar * Connecting cable for charger Storage compartment for mains cable Driving lever Operator console Storage surface for cleaning set "Home base box“ Cover dirt water reservoir Holding rail for home base Recessed grip Cleaning he
Program selection switch 4 3 Before Startup 5 Installing the Brushes 6 BD model The disc brush must be installed before the initial operation (see "Maintenance work"). BR model The brushes are mounted. Install batteries 7 2 1 1 2 3 4 5 6 7 8 8 OFF Device is switched off Transport mode Driving to the Place of Use. Eco mode Wet clean the floor (with reduced brush speed) and vacuum up wastewater (with reduced suction). Normal mode Wet clean the floor and vacuum up dirt water.
Operation Installing the Vacuum Bar Insert the vacuum bar into the vacuum bar suspension in such a manner that the profiled sheet is positioned above the suspension. Tighten the wing nuts. Danger In dangerous situations, release the drive lever. Parking brake Loosen the parking brake; for that press the pedal downward and move it to the left. Then let the pedal go upward. Activate immobilising brake. Press the pedal downwards and move it to the right to lock it.
Setting the Vacuum Bar Oblique position To improve the vacuuming result on tiled floors the vacuum bar can be turned to an oblique position of up to 5°. Loosen the wing nuts. Turn the vacuum bar. Tighten the wing screws. Inclination If the vacuum result is unsatisfactory the inclination of the straight vacuum bar can be modified. Adjust the rotary handle to incline the suction bar.
Confirm the changed setting by pressing the Info button or wait till the set value is automatically accepted after 10 seconds. Select the next parameter by turning the Info button. After all desired parameters have been modified, turn the info button until "Exit menu" is displayed. Press the info button - you will exit the menu. Setting the language Press Info button - the set value blinks. Set the desired language by turning the info button.
Replace or turn vacuum lips 1 2 1 2 Wear indicator Vacuum lip The vacuum lips must be replaced or reversed if they are worn down to the wear indicator. Remove the vacuum bar. Unscrew the star grips. Insert a new brush roller. Reassemble the bearing lid in the reverse sequence. Repeat process on the opposite side. Replacing the disk brushes Press the pedal for changing the brushes downward beyond its resistance. Insert the push bow into the cleaning head intake.
Batteries Please observe the following warning notes when handling batteries: Observe the directions on the battery, in the instructions for use and in the vehicle operating instructions Wear eye protection Keep children away from acid and batteries Danger of explosion Fire, sparks, naked flames and smoking must be strictly avoided Danger of chemical burns Insert batteries and connect Caution When the batteries are installed and removed, the stability of the appliance can be compromised; ensure a safe sta
Faults Danger Risk of injury! Before working on the appliance, remove the Intelligent Key and the mains plug of the charger. Drain and dispose of the dirt water and the residual fresh water. Faults with display Display ERR_I_BÜRSTE_049 ERR_I_TURB_050 ERR_U_BATT_001 Remedy Check if foreign matters block the brushes; remove foreign matter if required. Check suction turbine for contamination and clean it if necessary. Check battery; charge it if required.
Accessories BR appliance B 80 (brush roller accessories) Part no.: Working width 750 mm Brush roller, red (medium, standard) 6.906-935.0 Brush roller, white (soft) Brush roller, orange (high/ low) 6.906-981.0 6.906-982.0 Brush roller, green (hard) Brush roller, black (very hard) 6.906-983.0 6.906-984.0 Pad roller shaft Roller pad, yellow (soft) Roller pad, red (medium) Roller pad, green (hard) 4.762-433.0 6.369-454.0 6.369-456.0 6.369-455.0 6.906-936.
Technical specifications BR appliance B 80 R 65 R 75 Power Nominal voltage Battery capacity Average power consumption Drive motor output (rated output) Suction engine output Brush engine output Vacuuming Vacuum power, air volume (max.) Vacuuming power, negative pressure (max.) Cleaning brushes Brush speed Dimensions and weights Theoretical surface cleaning performance Max. working range incline Fresh/dirt water reservoir volume Max. water temperature max.