Operation Manual

– 9
Illustration
 To stabilise, place the appliance into the cleaning
station.
Illustration
 Remove the fresh water tank from the appliance
using the handle.
Illustration
 Open fuel filler cap.
 Fill the fresh water tank with cold or lukewarm tap
water.
 KÄRCHER detergents/care agents can also be
added to the fresh water tank as required.*
See chapter "Detergents and care products".
 Do not exceed the "MAX" marking when filling.
 Close tank lock.
Illustration
 Insert the fresh water container into the appliance.
 The fresh water tank must sit snugly into the appli-
ance.
ATTENTION
*Follow the recommended dosage instructions on the
detergent/care agent.
ATTENTION
Illustration
The appliance must only be used for the intake of dirt
and fluids (max. 250 ml).
Illustration
Before beginning your work, remove any objects, such
as shards, pebbles, screws or toy parts from the floor.
Before use, check the floor for water consistency at sus-
pect areas. Do not clean water-sensitive coatings, such
as untreated cork floors (moisture ingress is possible
which may damage the floor).
Notes
To prevent yourself from tripping over network cables,
keep the handle in one hand, and the network cable in
the other.
Illustration
To avoid fresh footprints on the freshly-wiped floor, work
backwards towards the door.
 Hold the appliance at the handle at angle of approx.
60 degrees.
 Clean the floor by moving the appliance back and
forth at a similar speed as if you were vacuum
cleaning.
 If the floor is especially dirty, let the appliance glide
slowly across the floor.
 For scope of delivery of the roller pads in grey and
yellow: Both roller pads have the same functionali-
ty, they can be used for different areas of applica-
tion (colour distinction, e.g. for kitchen and bath-
room).
ATTENTION
After switching on the appliance, the cleaning rollers will
begin to rotate. Hold the handle tight to prevent the ap-
pliance from moving forwards by itself.
Make sure the fresh water tank is filled with water and
the waste water tank is fitted in the appliance.
Illustration
 Insert the mains plug into a socket.
Illustration
 In order to moisten the rollers fast, fill the cleaning
station with 50 ml fresh water using the supplied
measuring cup.
 Switch on the appliance and put it into operation in
the station for 5 seconds.
The appliance then has the ideal level of moisture
in order to allow fast cleaning.
Illustration
 Switch off the appliance; press the on/off button to
do so.
Illustration
 Remove the carrying handle from the cleaning sta-
tion and set it on the floor.
 Hold the appliance firmly using the handle.
Illustration
 To switch on the appliance press the on/off switch.
ATTENTION
Before filling the fresh water tank, please empty the
waste water tank. In this way you can avoid overflowing
of the waste water tank.
See Chapter "Emptying the waste water tank".
Illustration
 Place the appliance in the cleaning station.
Illustration
 Remove the fresh water tank from the appliance
using the handle.
Illustration
 Open fuel filler cap.
 Fill the fresh water tank with cold or lukewarm tap
water.
 Add cleaning or disinfecting agent as required.
 Do not exceed the "MAX" marking when filling.
 Close tank lock.
Illustration
 Insert the fresh water container into the appliance.
The fresh water tank must sit snugly into the appli-
ance.
ATTENTION
The water level must be checked at regular intervals to
prevent the waste water tank from overflowing. Do not
exceed the "MAX" marking.
Illustration
 Place the appliance in the cleaning station.
Illustration
 Hold the waste water tank at the bottom handle. At
the same time, press the upper handle downwards
with your thumbs.
Illustration
 Remove waste water tank.
Commissioning
Fill fresh water reservoir
Operation
General information on the
operation
Start working
Refill detergent
Emptying the waste Water tank
17EN