POPPER USER MANUAL All products are trademarks of ROVSUN. Design & utility patented or patents pending. ©2020 Copyright ROVSUN ALL rights reserved. www.rovsun.
Single door:ZT8501; RPM-B 8 Oz. RETRO BLACK POPPER RPM-R 8 Oz. RETRO RED POPPER RPMC-B 8 Oz. RETRO BLACK POPPER WITH CART RPMC-R 8 Oz. RETRO RED POPPER WITH CART Appliance Specifications: 120 Volts, 60 Hz, 850 Watts ETL Approved THIS PRODUCT IS FOR USE IN 120V AC OUTLET ONLY.
INTRODUCTION Thank you for purchasing this 8OZ RETRO POPCORN MACHINE! This popper will be the hit of every party, home movie theatres, little League, varsity games, businesses, etc. Convenient 3 switches operation Includes a light warmer, stirrer, and pot heater. The RETRO POPCORN MACHINE features a large, stainless steel kettle with a built-in stirring system, providing hot, fresh, kettle cooked popcorn per batch.
! IMPORTANT PRECAUTIONS 1. NEVER immerse any part of this equipment in water. 2. NEVER use near water, gas or electric burner. 3. NEVER place objects in contact with heated surfaces. 4. NEVER use an abrasive sponge nor cloth. 5. NEVER use a scouring pad on the appliance. 6. NEVER leave appliance unattended while in use. 7. ALWAYS unplug the equipment when not in use, and during cleaning or servicing. 8. DO NOT operate this appliance with a damaged cord or plug, nor if the appliance ever malfunctions. 9.
8 OZ POPCORN MACHINE PARTS: A. Main Unit x1 D. Popcorn scoop x1 G. Popcorn cup x3 B. Door x1 E. Corn measuring cup x1 H. Powder shaker x1 C. Kettle x1 F. Oil measuring cup x1 I.
ASSEMBLY OF THE MAIN UNIT 1. Remove all packaging and take out the parcel which was stored in the Main unit (A), find Glass doors (B) and insert pins into hinges. meanwhile, put the four triangular caps (I) onto the corner of top plate. Note: Always place the equipment on a sturdy & level base. 2.Put the Kettle (C) onto hangers which located in the Main Unit (A), slip hanger bars into slots on hangers. Make sure gears are properly meshed together. 3.
POPCORN MACHINE CART PARTS: J. Storage case x1 N. Base leg with Axle (assembly with wheels) x1 R. Hex bolt x8 K. Working platform x1 L. Handlex1 O. Base leg connector x2 P. Wheel x2 S. Hex bolt x8 T. Nut x8 U. Cap nut x2 M. Base Leg x1 Q. Wrench x2 V.
ASSEMBLY OF BASE SUPPORT 1. Assemble the Working platform (K) onto the left side of Storage case ,and the Handle (L) onto the right side. Secure with Hex bolts(R) and Washers (V) & Nut (T) . 2.Put one wheel (P) on one side of Axel (N), add Washers and Cap nuts (U), spin a few threads in. then repeat on other side. Tighten by wrench provided (Q). Then connect two Base legs (M&N) by Base connectors (N),secure with Hex bolt (R). 3.
ASSEMBLY OF MAIN UNIT & BASE SUPPORT 1. Put the top Main unit onto the assembled base support, turn and insert four pins into the hole of Storage case (J). ATTENTION: Make sure the Main unit and assembled base support are well secured by pins. DO NOT move the equipment before security.
HOW TO OPERATE WARMER SWITCH: Supplies power to the interior cabinet light and warming element in the bottom tray. STIRRER SWITCH: Supplies power to the agitator motor, opreates the stirrer which in side the kettle. Be sure gears on the kettle and motor are properly meshed together before starting. POT HEATER SWITCH: supplies power to the heating element in the kettle. Kettle gets very hot, ALWAYS use handle to operate.
CLEANING & MAINTENANCE 1.Turn all switches to the OFF position. 2.Unplug the outer plug to the outlet . 3.Allow kettle to cool at least 1 hour before cleaning. DO NOT use ice or water to cool down a hot kettle! 4. After cool, unplug the kettle motor plug and remove the kettle from main unit. 5. Fill ²⁄ ³ of Kettle with hot, soapy water and let sit for 15 – 20 minutes to cut the grease. (Time may vary – use your own judgment depending on the amount of cleaning necessary.) 6. Empty water.
All products are trademarks of ROVSUN. Design & utility patented or patents pending. ©2020 Copyright ROVSUN ALL rights reserved. www.rovsun.