SDS

ManualsBrandsKarnak ManualsBuilding materials501 5-Gal. Elasto-Brite Acrylic Roof Coating

Page: 1 of 5

Material Safety Data Sheet

24 HR. CHEMTREC EMERGENCY #: 1-800-424-9300

(OUTSIDE THE U.S. & CANADA: 1-202-483-7616)

HAZARD RATING

4 - EXTREME

3 - HIGH

2 - MODERATE

1 - SLIGHT

0 - INSIGNIFICANT

Health

Fire

Special

Reactivity

SECTION 1 - PRODUCT IDENTIFICATION

IDENTITY: Elastobrite MANUFACTURER:

501 Karnak Corporation

330 Central Ave.

Clark, NJ 07066 U.S.A.

DATE: April 15, 2009

Revision:2 Telephone #: 1-732-388-0300

24 HR CHEMTREC EMERGENCY NUMBER 1-800-424-9300

(OUTSIDE THE U.S AND CANADA 1-202-483-7616)

SECTION 2 - COMPOSITION, INFORMATION ON INGREDIENTS

Other Limits

Components CAS# Weight % OSHA PEL ACGIH TLV Recommended

Polymer Mix, Propriety 30-80 NA NA NA

Titanium Dioxide 13463-67-7 5-25 5 mg/m

5 mg/m

Water 7732-18-5 2-50 NA NA NA

Feldspar 68476-25-5 15-25 NA 0.8mg/m

Zinc Oxide 1314-13-2 2-7 10 mg/m

10 mg/m

Ethylene Glycol 107-21-1 0-1 200 ppm 5 ppm NA

Ammonia 1336-21-6 0-5 50 ppm 25 ppm NA

Hydroxyethyl Cellulose 9004-62-0 0-2 NA 10 mg/m

Ester Alcohol 25265-77-4 0-2 NA NA NA

2-N-Octyl-4-Isothiazolin-3-One26530-20-1 0-2 NA NA NA

Defoamer-

petroleum Hydrocarbon 64741-95-5 0-2 5 mg/m

5 mg/m

Amine/Alcohol Hydrocarbon 124-68-5 0-2 NA NA NA

PEL = Permissible Exposure Limits OSHA = Occupational Safety and Health Administration

TLV = Threshold Limit Value ACGIH = American Conference of Governmental Industrial Hygienists

N.E. = Not Established NIOSH = National Institute for Occupational Safety and Health

N.A. = Not Applicable.

SECTION 3 - HAZARDS IDENTIFICATION

Potential Health Effects:

Fumes from product can be unpleasant, may cause nausea, headache and irritating to eyes, skin, and respiratory

tract.

Summary of content (5 pages)

PAGE 1
Page: 1 of 5 Material Safety Data Sheet 24 HR. CHEMTREC EMERGENCY #: 1-800-424-9300 (OUTSIDE THE U.S. & CANADA: 1-202-483-7616) HAZARD RATING 4 - EXTREME 3 - HIGH 2 - MODERATE 1 - SLIGHT 0 - INSIGNIFICANT Fire Health 1 0 0 Reactivity Special SECTION 1 - PRODUCT IDENTIFICATION IDENTITY: Elastobrite MANUFACTURER: 501 Karnak Corporation 330 Central Ave. Clark, NJ 07066 U.S.A.
PAGE 2
MSDS Page 2 of 5 Elastobrite rev2 SECTION 4 - FIRST AID MEASURES Eye Contact: If this product comes in contact with eyes, Flush eye with plenty of water for at least 15 minutes and seek medical attention. Skin Contact: If this product comes in contact with skin, remove material with mineral oil, then wash with soap and plenty of water. Inhalation: If respiratory discomfort occurs, remove to fresh air. If discomfort continues, administer oxygen and get medical attention.
PAGE 3
MSDS Page 3 of 5 Elastobrite Rev2 SECTION 7 - HANDLING AND STORAGE Vapors are heavier than air and may travel along the ground or be moved by ventilation to locations distant from the point of material handling. To prevent from entering buildings or confined areas, close all air intake sources near the material handling or the work area. Avoid prolonged or repeated inhalation of vapors or spray mists. Avoid prolonged or repeated skin contact. Adhere to good hygienic practices.
PAGE 4
MSDS Page 4 of 5 Elastobrite Rev2 SECTION 10 - STABILITY AND REACTIVITY Stability: Stable Conditions to Avoid: Auto-ignition temperature unknown. Incompatibility (Materials to Avoid): May react with strong oxidizing materials. Avoid Freezing Hazardous Polymerization: Will not occur. SECTION 11 - TOXICOLOGICAL INFORMATION Product may cause respiratory irritation, headache, dizziness, nausea and vomiting. Prolonged or repeated contact with skin may cause dermatitis.
PAGE 5
MSDS Page 5 of 5 Elastobrite Rev2 SECTION 14 - TRANSPORTATION INFORMATION The description shown may not apply to all shipping situations. Consult 49 CFR, or appropriate regulations, for additional description requirements.