Owners Manual Aerating Fountains 3400JF & 3400HJF 4400JF & 4400HJF Contents Important Safety. . . . General Instructions. . . . Cord Gauge Chart. . . . Unit Specs. . . . 3400JF, 3400HJF Parts Included. . . . 3400JF, 3400HJF Assembly. . . . 4400JF, 4400HJF Parts Included. . . . 4400JF, 4400HJF Assembly. . . . Nozzle Options. . . . Installation Instructions. . . . Control Panel Installation. . . . C-25 Timer Control Instructions. . . . C85 non-metallic Wiring Diagram. . . .
THANKS We at Kasco Marine, Inc. would like to both thank and congratulate you on your purchase of the JF model aerating fountain. We appreciate you choosing Kasco and for your purchase. Your decision to purchase Kasco’s JF model Aerating Fountain will not disappoint you. The JF model Aerating Fountain will be a great addition to your body of water. It will help improve the water quality by adding much needed oxygen and circulation.
backs each 3400JF model Fountain with a 2 Year Warranty. This warranty covers any and all manufacturers defects within 2 years from the date of purchase (See Warranty & Return Policy). Please register your Fountain online at: www.kascomarine.com (Under the Technical tab) tant to store them upside down if they are going to be sitting for long periods of time. Units that sit upright on a shelf for many months, or even years have a greater likelihood of seals drying out.
3400JF, 3400HJF Parts Included 1. 3400JF Aerating Fountain (Unit with cord or unit with Disconnect) (1) 2. Float (with two 50’ mooring ropes attached) (1) 3. 1/4-20 x 3 1/4” Phillips Pan Head Screw (4) 4. 1/4” split washers (4) 5. 1/4” (3/4” outer diameter) Flat Washer (4) 6. 3/8”-16 x 1-3/4” Hex Head Bolt (2) 7. 3/8” Flat Washer (4) 8. Cushions for Legs (4) 9. Bottom Screen section (3) 10. Bottom Screen Clips (2) 11. 3/8”-16 Nylon Lock Nut (2) 12. #8 nut (6) 13. #8 flat washer (12) 14.
Rest the float on the 4 legs of the housing making sure logo on float is up. 7. Secure the 3 sections of the screen together in 6 places using #8 screw (Part 15), #8 lock washer (part 14), two #8 flat washers (part 13), and #8 nut (part 12). Do not overtighten. cushion logo #8 nut 4. Ensure correct alignment by twisting the float gently around the motor housing until the power cord guide lines up with the cord. See diagram below of bottom side of float.
3/8” lock nut 3/8” flat washer Bottom screen clip 3/8” flat washer 3/8” bolt 12. Thread one rope through one weighted tube rope Weight and position it approximately 6’ from the float. Next, thread the end of the rope back through the opening facing the float (as shown). Repeat with the second rope and weight. If ready to install in the pond, go to Installation instructions. Light Kits can also be installed at this time, go to Light kit instructions. 4400JF, 4400HJF Parts Included 10.
3 4 5 6 7 2 1 8 9 10 12 13 14 15 Set of 5 Interchangeable Nozzles (5) 1. 3/8” x 2.25” bolt (1) 2. 3/8” x 4” bolt (1) 3. Linden Nozzle (1) 4. Sequoia Nozzle (1) 5. Juniper Nozzle (1) 6. Willow Nozzle (1) 7. Cypress Nozzle (1) 8.
3. Ensure correct alignment by twisting the float gently around the motor housing until the power cord guide lines up with the cord. See diagram of bottom side of float. power cord Bolt holes guide 4. Use one of the 1/4”-20 x 3-1/2” Phillips Pan Head Screws (Part 3), one 1/4” split washer (Part 4), and a 1/4” Flat Washer (Part 5) to secure the float. Make sure the split washer goes between the bolt head and the flat washer.
clip. 3/8” lock nut 3/8” flat washer Bottom screen clip 3/8” flat washer 3/8” bolt 12. (optional - weight not included) Thread one rope through one weighted tube rope Weight and position it approximately 6’ from the float. Next, thread the end of the rope back through the opening facing the float (as shown). Repeat with the second rope and weight. If ready to install in the pond, go to Installation instructions. Light Kits can also be installed at this time, go to Light kit instructions.
Linden Display: The Linden nozzle (marked L inside one of the fins) uses the 3/8” x 4” bolt. Model 3400JF/HJF 4400JF/HJF Height 6’ 8’ Width 18’ 25’ Willow Display: The Willow nozzle (marked W on the inside of the cone) uses the 3/8” x 4” bolt. Model 3400JF/HJF 4400JF/HJF Height 4.5’ 6’ Width 15’ 23’ Sequoia Display: The Sequoia nozzle is not marked and uses the shorter 3/8” x 2.25” Model 3400JF/HJF 4400JF/HJF Height 7’ 9.
STEP THREE Follow all local and national electrical codes for this installation and Consult a qualified electrician or service person if needed. (For 120V Installations) Plug the aerator cord into the C-25 outlet labeled “UNIT”. If lights are included, plug the Transformer cord into the C-25 outlet labeled “LIGHT”.
should be stripped back at least 3inches. Follow the connection diagram for terminating these three wires to the terminal blocks in the control panel. L1 __________ Black connects to Terminal #4 White connects to Terminal #5 Green connects to Terminal G Date installed _____/_____/_____ Light Kit connection: If you purchased a Kasco light kit(s) for your aerator, follow the light kit installation instructions for mounting the light kit(s) to the aerator float.
ENTER THE WATER WHEN A UNIT IS IN OPERATION! TIMER-OPERATION INSTRUCTIONS C-25 Control Box will turn the aerator/fountain ON & OFF with the TIMER. Kasco lights will turn ON with the PHOTO EYE and OFF with TIMER. C-25 Control Box is to be used with Kasco Approved Lights ONLY! • • • • Insert “ON” (GREEN) and “OFF” (RED) trippers into dial at desired ON and OFF times. Turn dial clockwise one or more revolutions until correct time-of-day (AM or PM) in window is aligned with the arrow.
C85 non-metallic Wiring Diagram 14
C85 / C95 non-metallic and 3 Phase Control Panel Timer TIME CLOCK SETTING To set the current time, turn the inner dial clockwise. Do not set the time by rotating “outer” dial. Turn the minute hand or small plastic inner dial clockwise until the time of day on the outer dial is aligned with the triangle marker on the inner dial (two o’clock position). Example for 10:00 AM. Turn the minute hand clockwise until 10:00 AM is aligned with the triangle on the inner dial.
Maintenance Recommendations ** Under No Circumstances should anyone enter the water while a fountain is operating. ** ** Please keep the original box for maintenance shipping. ** The following maintenance procedures can be utilized to ensure many years of quality performance from your Kasco Fountain and reduce the need for more costly repair work. PROPER INSTALLATION: Proper installation of Kasco equipment will include a power source with ground fault interruption (GFI).
void the warranty. This includes tampering with the unit, power cord, and/or control box. Please contact Kasco Marine, Inc. at 715-262-4488 for your nearest Authorized Repair Center. Warranty Policy Warranty Period: Models: 3400JF, 3400HJF, 4400JF, 4400HJF - 2 years Kasco® Marine, Inc. warrants this Fountain to be free from defects in material or workmanship (except for the ropes, power cord, and propeller) under normal use and service. The Kasco Marine, Inc.
dress for correspondence regarding the warranty claim. Any expedited shipping method for the return of the unit is at the customer’s expense. Kasco Marine will return units repaired under warranty at our expense via ground freight within the continental United States. Other Repairs: Most failed equipment can be repaired at substantially lower costs than replacement with new. Please ship according to the instructions in the previous section.
you are noticing these symptoms, the unit should be unplugged immediately because the Thermal Overload will continue to turn on and off until it burns out and damages the motor. The unit should be unplugged and taken out of the water to find the cause of the problem. The problem could be one of many, such as, low water levels, build-up on the unit to prevent heat dissipation, something inhibiting the free rotation of the shaft, etc.
3400J Replacement Parts 3400J REPLACEMENT PARTS 19 14 15 13 18 11 12 9 1 10 18 8 2 7 ITEM NO. PART NO.
4400J Replacement Parts 21
800 Deere Rd. Prescott, WI 54021 Phone: 715-262-4488 - Fax: 715-262-4487 www.KascoMarine.com Sales@KascoMarine.com Customer Repair Form * Important Reminders * • All repairs sent in MUST be accompanied by a copy of this completed sheet! • Routine maintenance consists of checking the zinc anode regularly and replacing if necessary, keeping the unit clean, keeping the stainless steel can clean, and having the seals and oil replaced every 3 years depending on use.
Registration Information Please register your fountain online at: www.kascomarine.com (Under the Technical Tab) Also fill in the information below and keep for your records. Model # (Ex. 3400JF)_______________________________ Serial # (Ex. 8001J31725)______________________________ Purchase Date:_____________________ Purchased From:___________________________________ Registration Date: ___________________________ Kasco Marine, Inc. 800 Deere Rd.
