Warranty

kovaproducts.com Rev. 0.1 | 2020.05
FCC responsible party name: Katerra, Inc.
Address: 2494 Sand Hill Road
Bldg 7, Suite 100
Menlo Park, CA 94025
United States
650-422-3572
Warranty
This product is warranted to be free from defects in workmanship and materials for up to
5 years from date of purchase.
Pre-Installation
Tools Required (not included)
Phillips screwdriver Electric drill with
3/16 in. and 5/34 in. drill bits
Measuring tape Safety glasses
Product Description
A
B C D E
F
H
G
Part Description Qty. Part Description Qty.
A Fixture housing 1 E Wire nuts 3
B 8-32 x 25 mm machine screws 2 F Mounting bracket 1
C Drywall anchors 2 G Lock/release buttons 2
D Flush mounting screws 2 H Fixture endcaps 2
Safety Information
WARNING: Carefully read and understand the information given in this manual before
beginning the assembly and installation. Failure to do so could lead to electric shock,
re, or other injuries that could be hazardous or even fatal.
WARNING: CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTORS. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE
WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH
THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
WARNING: The unit is intended to be installed directly beneath a ceiling-mounted
junction box.
WARNING: Do not install on radiant-heating type ceiling.
WARNING: Voltage and current rating of xture: 120-277VAC 60Hz.
WARNING: Any changes or modications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
4 Securing the Fixture Mounting Bracket
D
F
B
Align the xture mounting bracket (F) center mounting slots with the junction box
mounting holes. Use the 8-32x25 mm machine screws (B) to secure the xture
mounting bracket (F) to the junction box. Use the ush mounting screws (D) to secure
the xture mounting bracket (F) to the outer mounting holes.
5 Connecting the Cables
A
While holding the xture housing (A) rmly, connect the xture housing cable to the
driver cable. Ensure the quick-connect makes a secure connection. Do not allow the
xture housing to hang by the wiring unsupported.
6 Attach the Fixture Housing
A
H
F
H
F
1. While holding the xture endcaps (H), align the xture housing (A) with the
mounting bracket (F). Push the xture housing onto the mounting bracket until
the xture housing snaps into place. Gently pull on the xture housing to ensure
proper installation.
2. Turn on the power at the circuit breaker box and verify that the xture functions
properly.
Install Instructions
Product
LED Snap Wrap
Model Number
K0000025647
Before You Begin
Remove the xture from the carton and check for any shipping damage.
WARNING: Ensure that the power is turned off at the circuit breaker.
CAUTION: WIRING AND FIXTURE OPERATION
Assistance may be required to support the xture during installation.
1 Flush Mount Installation
Ceiling
Ceiling
JOIST DRYWALL
C
5/64 in.
3/16 in.
Ceiling
38-2/5 in.
38-2/5 in.
Junction Box
Installing to a wooden joist (preferred):
Drill 5/64 in. pilot holes in the ceiling/joists 38-2/5 in. apart.
Installing to drywall with no wooden joist:
Drill 3/16 in. pilot holes in the ceiling 38-2/5 in. apart. Insert drywall anchors (C) into
pilot holes.
2 Remove the Mounting Bracket
A
G
F
Press the lock/release buttons (G) on both sides of the xture housing (A) to remove
the xture mounting bracket (F).
3 Connect the Electrical Wires
Black
White
F
E
Ground
While supporting the xture mounting bracket (F), hold it close to the ceiling and make
the following wire connections:
1. Connect the black xture wire to the black supply wire using a wire nut (E).
2. Connect the white xture wire to the white supply wire using a wire nut (E).
3. Connect the xture ground wire to the supply ground wire using a wire nut (E).
4. Carefully push all wires and wire nuts inside the junction box.