User's Manual
Table Of Contents
- 1 About this Document
- 2 General Information
- 3 Preconditions and Requirements
- 4 Installing the C-Hub
- 5 Installing the E-Hub
- 6 Installing the HPRU
- 7 Cabling
- 8 System Documentation
- 9 Glossary
- 10 List of Diagrams
- 11 List of Tables
- Fig. 1: Scope of delivery
- Fig. 2: Example of a handover point for the BTS signals at a c-rail
- Fig. 3: Example of a handover point for the BTS signals with individual loads with short patch cables at a c-rail
- Fig. 4: Clearance Ⓐ above radiation fins of the installed devices
- Fig. 5: Sliding rails Ⓑ
- Fig. 6: Power distribution bar ① mounted on the left-hand traverse
- Fig. 7: Plugs for power connection: ① is for red circuit, ② for black circuit
- Fig. 8: Attaching a 19" mounting bracket
- Fig. 9: Attached sliding rails Ⓑ
- Fig. 10: Place C-hub in rack
- Fig. 11: Fix C-hub with screws
- Fig. 12: Connect power cable at rear side
- Fig. 13: Connect ground cable at rear side
- Fig. 14: Attaching a 19" mounting bracket
- Fig. 15: Marking position of mounting holes
- Fig. 16: Mounting completed
- Fig. 17: Connect power cable at rear side
- Fig. 18: Connect ground cable at rear side
- Fig. 19: Attaching handle
- Fig. 20: Attaching bracket Ⓐ
- Fig. 21: Marking mounting holes for bracket Ⓑ
- Fig. 22: Prepare expansion bolts for bracket Ⓑ
- Fig. 23: Mounting accessories for bracket Ⓑ
- Fig. 24: Bracket Ⓑ mounted
- Fig. 25: Hook HPRU into bracket Ⓑ (①) and fix from top (②).
- Fig. 26: HPRU fixed from top
- Fig. 27: Fix HPRU from side
- Fig. 28: Connect power cable at bottom side
- Fig. 29: Connect ground cable at bottom side
- Fig. 30: Interfaces at the C-hub front side
- Fig. 31: Interfaces at the C-hub rear side
- Fig. 32: Interfaces at the E-hub front side
- Fig. 33: Interfaces at the E-hub rear side
- Fig. 34: Interfaces at the HPRU connector side
- Fig. 35: Fibre optical cable layout
- Fig. 36: Coaxial cable layout
- Fig. 37: Power supply cable layout
- Tab. 1: Symbols and signal words
- Tab. 2: Storage of the system documentation
11 of 50936.5467 0.92
2.4 Electrical and Mechanical Safety
Warning
Risk of injury due to electricity.
● All K-BOW racks must be connected to a protective earthing conductor.
● Do not connect system components to the power supply during installation.
Connection to the power supply must be performed by a trained, quali ed and
authorised specialist.
● Disconnect the system from external power before disassembly.
● Only install and uninstall system components if they are de-energised.
● Do not touch parts that are at a hazardous voltage. This also applies if fuses inside the
device have been removed.
The system has a supply voltage of up to 240V alternating voltage. If touched, there is
a risk of death due to electric shock.
● Install the socket near the equipment and make sure it is easily accessible.
● An appropriate fuse protection for all power supply feed lines of the K-BOW system
protection must be provided by the customer.
All power supply feed lines of the K-BOW system must be equipped with an
overvoltage protector for medium voltage loads and automatic circuit breakers (delay
fuse) of 10Amax. for overcurrent protection.
The correct performance must be checked and recorded according to current regulations.
● Only IEC-60320 C13/C14 power supply cables and appliance couplers speci ed for
10Amin. continuous load are allowed.
● Observe extension cord and power strip ratings. Make sure that the total ampere
rating of all products plugged into the extension cord or power strip does not exceed
80percent of the extension cord or power strip ampere rating limit.
● Do not modify power cords or plugs. Consult a licensed electrician or your power
company for site modi cations. Always follow your local and national wiring rules.
● Unplug the power cable(s) of a switched-mode power supply to completely disconnect
the power supply unit and the connected devices from the mains. If redundant
switched-mode power supplies are used, unplug the power cables of all power supply
units concerned.
● All fuses inside the system may only be replaced by original parts.
Warning
Risk of injury due to hot surface.
Do not touch hot surfaces during operation. Allow hot surfaces to cool before touching
them.