Preparation Before Use Playing the Piano Music Menu CA93/CA63 Recorder Owner’s Manual Settings Appendix
Thank you for purchasing this KAWAI Concert Artist digital piano. This owner’s manual contains important information regarding the usage and operation of the CA93 & CA63 digital pianos. Please read all sections carefully, keeping this manual handy for future reference.
Preface About this Owner’s Manual Before attempting to play this instrument, please read the Preparation Before Use section from page 10 of this owner’s manual. This section explains the name and function of each part, how to connect the power cable, and how to turn on the power.
Important Safety Instructions SAVE THESE INSTRUCTIONS INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING CAUTION TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS : RISQUE DE CHOC ELECTRIQUE - NE PAS OUVRIR. TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING - When using electric products, basic precautions should always be followed, including the following. WARNING The product should be connected to an AC outlet of the specified voltage.
CAUTION Indicates a potential hazard that could result in injury or damage to the product or other property if the product is handled incorrectly. Do not use the product in the following areas.
) , ) $ * ( - , - , + ) ( , , ) # % Should an abnormality occur in the product, immediately turn the power OFF, disconnect the power cord plug, and then contact the
Table of Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Concert Magic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Important Safety Instructions . . . . . . . . . . . . . . . . . 4 1. Performing a Concert Magic song . . . . . . . . . . . . . . .32 Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2. Concert Magic demo mode . . . . . . . . . . . . . . . . . . . . .33 3.
Virtual Technician . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 1. Voicing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 2. Damper Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 Appendix Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Sound List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 3. String Resonance . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Part Names and Functions Preparation Before Use KAWAI CA93 Concert Artist d c a e f g b h i j m k (13) p s 10 n o q r
a POWER switch k METRONOME button This switch is used to turn the CA93/CA63 digital piano on/off. Be sure to turn off the instrument after playing. This button is used to turn the metronome function on/off, and also to adjust the tempo, time signature (or beat), and volume settings. b MASTER VOLUME slider c LCD display The LCD display provides useful information such as the currently selected sound name, settings values, and the status of other functions when active.
Setting Up the Piano 1. Connecting the power cable to the instrument CA63 Connect the included power cable to the ‘AC IN’ inlet located on the back side of instrument in the bottom left corner. Connect the included power cable to the ‘AC IN’ inlet located on the right hand side, towards the back of the instrument. 2. Connecting the power cable to an outlet 3. Turning on the power Connect the instrument’s power cable to an AC outlet.
Adjusting the Volume / Using Headphones Adjusting the volume The MASTER VOLUME slider controls the volume level of the instrument’s speakers, or headphones if connected. Move the slider up to increase the volume, and down to decrease the volume. Increase volume Preparation Before Use Use this slider to set the volume to a comfortable listening level - the middle is often a good starting point.
Selecting Sounds The CA93/CA63 digital piano features a wide selection of realistic instrument sounds suitable for various musical styles. Sounds are arranged into eight categories, with several sounds assigned to each category button. For a complete listing of sounds available on the CA93 & CA63 instruments, please refer to page 83 of this owner’s manual. By default, the ‘Concert Grand’ sound will be selected automatically when the instrument is turned on.
Using the Pedals As with a grand piano, the CA93/CA63 digital piano features three pedals: sustain, sostenuto, and soft. Soft pedal Sostenuto pedal Sustain pedal (right pedal) Sostenuto pedal (centre pedal) Depressing this pedal sustains the sound after one’s hands have been lifted from the keyboard - greatly enriching the piano sound, while also assisting smooth ‘legato’ passages.
Reverb Reverb adds reverberation to the sound, simulating the acoustic environment of a recital room, stage, or concert hall. The CA93/CA63 digital piano features five different reverb types. Reverb types Reverb type Description Room 1 Simulates the ambiance of a living room or small rehearsal room. Room 2 Simulates a larger room than Room 1. Stage Simulates the ambiance of a small hall or live stage. Hall 1 Simulates the ambiance of a concert hall or theater.
Effects In addition to reverb, various other effects can be applied to the selected sound, altering the tonal character and feeling of the instrument. The CA93/CA63 digital piano features seven effect types. Effect types Effect type Description Chorus Simulates the rich character of a vocal choir or string ensemble, by layering a slightly detuned version of the selected sound over the original, thus enriching the tonal character. Delay 1 / 2 / 3 Adds an echo to the selected sound.
Adjusting Effect Settings It is also possible to adjust settings for each effect, further altering the tonal character of the selected sound. Effect settings and explanation Effect type Chorus Delay 1 / 2 / 3 Tremolo Playing the Piano Rotary 1 / 2 Adjustable settings Explanation Depth Adjusts the depth (strength) of the Chorus effect. Speed Adjusts the speed of the Chorus effect. Depth Adjusts the depth (strength) of the Delay effect. Time Adjusts the time (length) of the Delay effect.
Dual Mode The Dual Mode function allows two sounds to be layered together, creating a more complex sound. For example, a piano sound layered with strings, or an electric piano combined with a choir, etc. Entering dual mode Press and hold a SOUND SELECT button, then press another SOUND SELECT button. Press one button, then another The LED indicators for both buttons will turn on to indicate that the two sounds have been selected, and their names will be shown in the LCD display.
Split Mode The Split Mode function divides the keyboard into two sections, allowing each section to be played with a different sound. For example, a bass sound in the lower section, and a piano sound in the upper section. Entering split mode Press the SPLIT button. The LED indicator for the SPLIT button will turn on to indicate that split mode has been enabled.
Four Hands Mode The Four Hands Mode function divides the keyboard into two sections in a similar way to that of the Split Mode function. However, the octave/pitch of each section is also adjusted, while the sustain (right) pedal and soft (left) pedal act as separate sustain pedals for the upper and lower sections respectively.
Metronome / Drum Rhythms The Metronome function provides a steady beat to aid practicing the piano at a consistent tempo. In addition to regular metronome beats, the CA93/CA63 digital piano also features a variety of drum rhythms to accompany most playing styles and musical genres. Turning the metronome on/off Press the METRONOME button. The LED indicator for the METRONOME button will turn on to indicate that the metronome is in use, and a 1/4 beat will start to count.
Registration Memories The Registration function allows the current instrument setup (sound selections, split point, reverb and effect settings, and various other panel options) to be stored in one of eight registration memories, and conveniently recalled at the touch of a button.
Demo Songs The Demo function provides an excellent introduction to the varied capabilities of CA93/CA63 digital piano. There are 36 different demonstration songs available, highlighting the instruments’ rich selection of high quality sounds and its power speaker system. For a complete listing of demonstration songs, please refer to page 84 of this owner’s manual. Entering demo mode Press the MUSIC button.
Piano Music In addition to the sound demonstration songs, the CA93/CA63 digital piano also features a selection of popular classical piano works from the Baroque and Romantic periods. Notated scores are provided in the separate ‘Classical Piano Collection’ book*, assisting the musical appreciation and study of each piece. For a complete listing of Piano Music pieces, please refer to the separate ‘Internal Song Lists’ booklet. * Depending on market area.
Lesson Function The Lesson function allows budding pianists to practice the piano using a selection of built-in song books and finger exercises. The left and right hand parts of each piece can be practiced separately, adjusting the tempo to perfect difficult passages, before being recorded for self-evaluation.
2 Listening to the selected lesson song This page will explain how to play and stop the selected lesson song, and adjust the tempo. Playing the lesson song After selecting a lesson book and song: Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the song starts to play. Book ame Song number * If the first bar of the song begins on an ‘up’ beat (i.e.
Lesson Function 3 Practicing left and right-hand parts separately This page will explain how to adjust the left and right-hand part volume of the selected lesson song (allowing each part to be practiced separately), and how to start playing a lesson song from a specific bar. Adjusting the left/right-hand part volume After selecting a lesson book and song: Adjust the volume of the right-hand part Press the e or f buttons to adjust the volume of the left/righthand part volume.
4 Repeating sections of a lesson song This page will explain how to repeat (loop) specific sections of the selected lesson song between a defined ‘A’ and ‘B’ point, allowing difficult passages to be practiced continuously. 1. Specifying the start point (A) of the loop After selecting a lesson book and song: Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn on, and a one bar count-in will be heard before the song starts to play.
Lesson Function 5 Recording a lesson song practice This page will explain how to record the left or right-hand parts of the selected lesson song, then play back the performance for self-evaluation. 1. Starting the lesson song recording After selecting a lesson book and song: Press the REC button. The LED indicators for the REC and PLAY/STOP buttons will turn on to indicate that recording mode is in use. A one bar count-in will be heard before the lesson song starts to play and record.
6 Finger Exercises The lesson function also includes a selection of finger exercises for practicing major and minor scales, arpeggios, chords, cadences, and Hanon exercises, with notated scores provided in the separate ‘Finger Exercises’ book. The CA93/CA63 digital piano can also evaluate one’s practice, analysing note accuracy, timing evenness, and note volume consistency, before displaying results for each category.
Concert Magic The Concert Magic function allows complete beginners to enjoy playing the piano by simply selecting one of the 176 pre-programmed songs, then tapping the keyboard with a steady rhythm and tempo. For a complete listing of available Concert Magic songs, please refer to the separate ‘Internal Song Lists’ booklet. 1 Performing a Concert Magic song The 176 Concert Magic songs are divided into banks ‘A’ and ‘B’, with each bank containing 88 songs. 1.
2 Concert Magic demo mode This function allows all of the Concert Magic songs to be played back randomly or in designated categories. Random playback Enter Concert Magic mode and select the desired song. Press the PLAY/STOP button. All 176 Concert Magic songs will be played in a random order until the PLAT/STOP button is pressed. * Press and hold the METRONOME button, then press the e or f buttons to increase or decrease the tempo of the song.
Concert Magic 3 Concert Magic song arrangement types Concert Magic songs are divided into three different arrangement types, each requiring a different level of skill to be performed correctly. Easy Beat These are the easiest songs to play. To perform them, simply tap out a constant steady beat on any key on the keyboard. Look at the following example for ‘Für Elise’. The Note Navigator indicates that a constant, steady rhythm should be maintained throughout the song.
Skillful These songs range in difficulty from moderately difficult to difficult. To perform them, tap out the rhythm of both the melody and the accompaniment notes on any key of the keyboard. The Note Navigator will be very helpful with the Skillful type songs. The song ‘Waltz of the Flowers’ is shown below. Waltz of Flowers Ä Ä Ä Ä < Key on X X X X X X X X X X X X X It may take a little practice to perform the Concert Magic songs proficiently.
Song Recorder (Internal memory) The CA93/CA63 digital piano allows up to 10 different songs to be recorded, stored in internal memory, and played back at the touch of a button. Each song consists of two separate tracks - referred to as ‘parts’ - that can be recorded and played back independently. This allows the left-hand part of a song to be recorded first on one track, and the right-hand part to be recorded later on the other track. 1 Recording a song 1. Entering song recorder mode Press the REC button.
3. Starting the song recorder Press a key on the keyboard. The LED indicators for the REC and PLAY/STOP buttons will turn on, and recording will start. * Recording can also be started by pressing the PLAY/STOP button, allowing a rest period or empty bar to be inserted at the beginning of the song. 4. Stopping the song recorder Press the PLAY/STOP button. The LED indicators for the PLAY/STOP and REC buttons will turn off, the recorder will stop, and the part/song will be stored in internal memory.
Song Recorder (Internal memory) 2 Playing back a song This function is used to playback recorder songs stored in internal memory. To playback a song/part immediately after recording, start this process from step 2. 1. Entering song play mode Press the PLAY/STOP button. The LED indicator for the PLAY/STOP button will turn on, and the Play Internal screen will appear with the currently selected song and part number shown in the LCD display.
3 Erasing a part/song This function is used to erase recorder parts/songs that have been recorded incorrectly, or are simply no longer required. 1. Entering erase mode Press the PLAY/STOP and REC buttons simultaneously. The LED indicators for the PLAY/STOP and REC buttons will start to flash, and the Erase screen will appear with the currently selected song and part number shown in the LCD display. 2.
Audio Record/Playback (USB memory) The CA93/CA63 digital piano is also capable of recording performances as digital audio - saving the data to a USB memory device in either MP3 or WAV format. This useful function allows professional quality recordings to be produced directly on the instrument - without the need for additional sound equipment - then emailed to friends and family, played back through an iPod, or edited and remixed further using an audio workstation.
4. Stopping the audio recorder, saving to USB Press the PLAY/STOP button. The LED indicators for the PLAY/STOP and REC buttons will turn off, and recording will stop A confirmation message will be shown in the LCD display, prompting to confirm the save operation. Save (Yes) Save to USB? ≤No Yes≥ Cancel (No) Press the e or f buttons to cancel or confirm the operation. 5.
Audio Record/Playback (USB memory) The CA93/CA63 digital piano is also capable of playing MP3 and WAV audio files stored on a USB memory device directly through the instrument’s speaker system. This function is particularly useful when attempting to learn the chords or melody to a new piece, or to simply play along with one’s favorite song. Audio Player supported format specifications Audio format Specifications Bitrate MP3 32 kHz/44.
File/folder listing screen The topmost two entries shown in [ ] symbols are used to select a recorder song stored in internal memory (‘Play Internal’ option), or to return to the previous folder (‘Parent Dir’ option). Select recorder song [Play Internal] [Parent Dir ] to previous folder The < > symbols are used to indicate a folder. Indicates a folder An example of a typical file/folder listing screen is shown below. For the purpose of illustration, the visible height of the screen has been extended.
Audio Record/Playback (USB memory) The CA93/CA63 digital piano also supports the playback of Standard MIDI File (SMF) song files stored on a USB memory device, allowing a vast selection of widely accessible music to be heard through the instrument’s exquisite Ultra Progressive Harmonic Imaging sound engine. 3 Playing a song file 1. Entering audio playback mode Connect a USB memory device to the USB port. Press the PLAY/STOP button.
4 Converting a song to an audio file The CA93/CA63 digital piano allows recorder songs stored in internal memory to be played back and saved (converted) as an audio file to a USB device in either MP3 or WAV format. 1. Selecting a song After recording a song to internal memory: Connect a USB memory device to the USB port. Select a song number Press the PLAY/STOP button, select the [Play Internal] option, then press the FUNCTION button.
Functions menus The Functions menus contain various options for adjusting the control operation and tonal characteristic of the CA93/CA63 digital piano. There are five different menus, each consisting of several different settings. Entering the Functions menus Press the FUNCTION button on the normal operation screen. The first functions menu (Basic Settings) will be shown in the LCD display. Functions 1.Basic Settings Press the c or d buttons to cycle through the different menus.
Basic Settings The Basic settings menu contains settings to adjust the pitch, tuning, and general sound of the instrument. This menu also allows favourite panel settings to be stored, or reset back to the original factory configuration. Basic Settings Page no. Setting name Explanation Default setting 1 Key Transpose Raise or lower the pitch of the keyboard in semi-tone steps. 0C 2 Song Transpose Raise or lower the pitch of SMF songs in semi-tone steps.
Basic Settings 1 Key Transpose The Key Transpose setting allows the pitch of the CA93/CA63 digital piano keyboard to be raised or lowered in semi-tone steps. This is particularly useful when accompanying instruments with different tones, or when a song learned in one key must be played in another key. When transposed, the song can be played in the original key, yet heard in a different key. 1. Selecting the Key Transpose setting Enter the Basic Settings menu (page 47).
3 Tone Control The Tone Control setting allows the overall sound character of the CA93/CA63 digital piano to be adjusted to provide the best sound quality within the area that the instrument is located. There are five different preset EQ settings available, with an additional ‘User’ setting allowing finer control over the different frequency bands. Tone Control types Tone Control type Explanation Off Tone control adjustment is not performed.
Basic Settings 4 Speaker Volume The Speaker Volume setting allows the maximum volume level of the instrument’s speaker output to be reduced, thus providing finer adjustment control over the master volume. This setting can also serve as a volume limiter, preventing the CA93/CA63 digital piano from being played too loudly in the home. * This setting does not affect the headphones or Line-out volume. 1. Selecting the Speaker Volume setting Enter the Basic Settings menu (page 47).
6 Wall EQ (CA93 only) The Wall EQ setting optimises the sound character of the soundboard speaker depending on whether the CA93 digital piano (back) is placed beside a wall, or in an area away from a wall. * This setting does not affect the headphones output. Wall EQ settings Wall EQ setting Explanation Off Optimises the soundboard speaker for placing the CA93 digital piano in an area away from a wall. On Optimises the soundboard speaker for placing the CA93 digital piano beside a wall. 1.
Basic Settings 8 Damper Hold The Damper Hold setting is used to determine whether sounds such as organ or strings should be sustained continuously when the sustain (damper) pedal is depressed, or whether these sounds should decay, naturally. Damper Hold settings Damper Hold setting Explanation Off Organ, string, etc. sounds will gradually decay, even while the sustain pedal is depressed. On Organ, string, etc. sounds will be sustained continuously while the sustain pedal is depressed. 1.
10 User Memory The User Memory function allows preferred panel settings to be stored in the instrument’s memory, and automatically recalled as the default settings every time the CA93/CA63 digital piano is turned on. User Memory Settings stored in User Memory Sound type (including starting sound and primary sound for each category) Effects/Reverb settings Basic Settings Virtual Technician Settings Key Settings Metronome tempo, time signature/rhythm, and volume 1.
Virtual Technician An experienced piano technician is essential to fully realise the potential of a fine acoustic piano. In addition to meticulously tuning each note, the technician also performs numerous regulation and voicing adjustments that allow the instrument to truly sing. The Virtual Technician settings of the CA93/CA63 digital piano simulate these refinements digitally, allowing performers to shape various aspects of the instrument’s character to suit their personal preferences.
1 Voicing The Voicing setting allows the character of the CA93/CA63 digital piano to be set to one of six different types. Voicing type Voicing type Description Normal The normal tonal character of an acoustic piano throughout the entire dynamic range. Mellow 1 A softer, more mellow tonal character throughout the entire dynamic range. Mellow 2 An even soften tonal character than Mellow 1.
Virtual Technician 2 Damper Resonance Depressing the sustain pedal of an acoustic piano raises all dampers, allowing the strings to vibrate freely. When a note or chord is played on the piano with the sustain pedal depressed, not only will the strings of the notes played vibrate, but also the strings of other notes, vibrating in sympathetic resonance. The CA93/CA63 digital piano recreates this phenomenon, with the Damper Resonance setting allowing the volume of this resonance to be adjusted.
3 String Resonance String Resonance refers to a phenomenon that exists in acoustic pianos whereby the strings of held notes resonate ‘sympathetically’ with other notes of the same harmonic series. The CA93/CA63 digital piano recreates this phenomenon, with the String Resonance setting allowing the volume of this resonance to be adjusted.
Virtual Technician 4 Key-off Effect When playing an acoustic piano - particularly in the bass region of the keyboard - if a key is played with force and released quickly, it is often possible to hear the feint sound of the damper touching the strings immediately before the vibrations are stopped. The CA93/CA63 digital piano recreates this phenomenon, with the Key-off Effect setting allowing the volume of this sound to be adjusted. 1.
5 Touch As with an acoustic piano, the CA93/CA63 digital piano produces a louder sound when the keys are struck with force, and a softer sound when the keys are played gently. The volume and tonal character change in relation to the strength and speed of playing - on a digital piano this system is referred to as ‘touch sensitivity’. The Touch setting allows the touch sensitivity of the keyboard to be conveniently adjusted.
Virtual Technician 5 Touch (cont.) 1. Selecting the Touch setting Enter the Virtual Technician menu (page 54). Press the e or f buttons to select the Touch setting. 2-5 Touch = Normal 2. Changing the Touch type Press the c or d buttons to cycle through the different Touch types. 2-5 Touch = Light Press a SOUND SELECT button to exit the Touch setting and return to normal operation. Creating a User Touch curve When selecting the ‘User1’ or ‘User2’ touch types. Press the REC button.
6 Temperament The Temperament setting allows the tuning system used by the CA93/CA63 digital piano to be changed from the modern ‘Equal Temperament’ standard to one of the various musical temperaments popularised during the Renaissance and Baroque periods. Available Temperament types Temperament type Description Equal Temperament (piano) This is the default temperament. When a piano sound is selected, the tuning will be stretched like an acoustic piano (equal temperament).
Virtual Technician 6 Temperament (cont.) 1. Selecting the Temperament setting Enter the Virtual Technician menu (page 54). Press the e or f buttons to select the Temperament setting. 2-6 Temperament = Equal(P.only) 2. Changing the Temperament type Press the c or d buttons to cycle through the different Temperament types. 2-6 Temperament = Meantone Press a SOUND SELECT button to exit the Temperament setting and return to normal operation.
7 Key of Temperament The Key of Temperament setting allows the key of the selected temperament to be specified. When using a temperament other than equal temperament, use this setting to specify the key signature of the piece. * This setting will only affect the ‘balance’ of the tuning system, the pitch of the keyboard will remain unchanged. 1. Selecting the Key of Temperament setting Enter the Virtual Technician menu (page 54). Press the e or f buttons to select the Key of Temperament setting.
Key Settings The Key Settings menu contains settings that affect instrument operation when using the Dual or Split modes. Key Settings Page no. Setting name Explanation Default setting 1 Lower Octave Shift Raise the pitch of the lower section in octave steps when using Split mode. 0 2 Lower Pedal On/Off Enable/disable sustain pedal for the lower section when using Split mode. Off 3 Layer Octave Shift Raise the pitch of the layered sound in octave steps when using Dual mode.
1 Lower Octave Shift The Lower Octave Shift setting allows the pitch of the lower section when using Split mode to be raised in octave steps. 1. Selecting the Lower Octave Shift setting Enter the Key Settings menu (page 64). The Lower Octave Shift setting will be selected automatically. 3-1 LowerOctave = 0 2. Adjusting the Lower Octave Shift value Press the c or d buttons to increase or decrease the value of the Lower Octave Shift setting.
Key Settings 3 Layer Octave Shift The Layer Octave Shift setting allows the pitch of the layered sound (shown in the second line of the LCD display) when using Dual mode to be raised or lowered in octave steps. 1. Selecting the Layer Octave Shift setting Enter the Key Settings menu (page 64). Press the e or f buttons to select the Layer Octave Shift setting. 3-3 LayerOctave = 0 2.
4 Layer Dynamics When using Dual mode, sometimes simply adjusting the volume balance between the two layered sounds is not enough to create the desired sound character, especially if both sounds are very dynamic. Layering two equally dynamic sounds can prove difficult to control and play comfortably. The Layer Dynamics Function allows the dynamic sensitivity of the layered sound to be reduced, in order to improve the blend between the two combined sounds.
About MIDI The term MIDI is an acronym for Musical Instrument Digital Interface, an international standard for connecting musical instruments, computers, and other devices to allow the exchange of performance data. MIDI terminals MIDI terminal Function MIDI IN Receiving note, program change, and other data. MIDI OUT Sending note, program change, and other data. MIDI THRU Passing along MIDI data to another MIDI device without processing.
MIDI functions The CA93/CA63 digital piano supports the following MIDI functions: Transmit/receive note information Transmit/receive Program Change number Transmit/receive note information from a MIDI-connected musical instrument or device. Transmit/receive program change data to/from a MIDIconnected musical instrument or device. Transmit/receive channel settings Transmit/receive pedal data Specify transmit/receive channels within the range of 1 to 16.
MIDI Settings 1 MIDI Channel (transmit/receive) The MIDI Channel setting allows the transmit/receive channel to be specified. The selected channel will function as both the transmit and receive channel (separate transmit/receive channels cannot be specified). 1. Selecting the MIDI Channel settings Enter the MIDI Settings menu (page 69). The MIDI Channel setting will be selected automatically. 4-1 MIDI Channel = 1 (TRS/RCV) 2.
2 Send Program Change Number The Send Program Change Number function allows the CA93/CA63 digital piano to transmit a program change number from 1 to 128. 1. Selecting the Send Program Change Number function Enter the MIDI Settings menu (page 69). Press the e or f buttons to select the Send Program Change Number function. 4-2 Send PGM # = 1 (UP+DOWN) 2. Specifying and transmitting a program change number Press the c or d buttons to increase or decrease the Program Change Number.
MIDI Settings 4 Transmit Program Change Numbers The Transmit Program Change Numbers setting determines whether or not the CA93/CA63 digital piano will transmit program change information via MIDI when the instrument’s panel buttons are pressed. Transmit Program Change Number settings Transmit PGM# setting Multi-timbral setting Effect of pressing panel buttons On Off, On1 SOUND SELECT buttons will send PGM# shown in the left column*.
5 Multi-timbral Mode The Multi-timbral Mode setting determines whether or not the CA93/CA63 digital piano is able to receive MIDI information on more than one MIDI channel simultaneously. This allows the instrument to play back multi-track, multi-timbral performance data sent from an external MIDI device. Multi-timbral Mode settings Multi-timbral Mode setting Effect on sound heard Off, On1 The sound shown in the left column is selected*. On2 The sound shown in the right column is selected*.
MIDI Settings 6 Channel Mute The Channel Mute setting determines which MIDI channels (1-16) are activated to receive MIDI information when Multi-timbral mode is enabled. This setting is available only when Multi-timbral mode is enabled. 1. Selecting the Channel Mute setting Enter the MIDI Settings menu (page 69). Press the e or f buttons to select the Channel Mute setting. 4-6 Ch 1 Mute = Play 2. Changing the Channel Mute setting Press the e or f buttons to select the MIDI channel.
USB MIDI (USB to Host connector) The CA93/CA63 digital piano features a ‘USB to Host’ type connector, allowing the instrument to be connected to a computer and utilised as a MIDI device. Depending on the type of computer and operating system installed, additional driver software may be required for USB MIDI communication to function correctly.
USB Menu The USB Menu contains functions to load and save recorder songs from/to a USB memory device. This menu also allows files to be renamed and deleted, and for the USB memory device to be formatted. USB Menu Page no. Function name Explanation 1 Load Song Load a recorder song from a USB memory device into the instrument’s internal memory. 2 Save Song Save a recorder song stored in internal memory to a USB memory device. 3 Rename Rename a file stored on a USB memory device.
1 Load Song The Load Song function allows recorder songs stored on a USB memory device to be loaded into the instrument’s internal memory. 1. Selecting the Load Song function Enter the USB menu (page 76). The Load Song function will be selected automatically. 5-1 Load Song ≥Press[F] Press the FUNCTION button. 2. Selecting the location for the song Press the c or d buttons to select the location (song number) that the song will be loaded into.
USB Menu 2 Save Song The Save Song function allows recorder songs stored in the instrument’s internal memory to be saved to a USB memory device. Once saved, this data can be played back or edited using computer software. 1. Selecting the Save Song function Enter the USB menu (page 76). Press the e or f buttons to select the Save Song function, then press the FUNCTION button. 5-1 Save Song ≥Press[F] 2.
3 Rename The Rename function allows song and audio files stored on a USB memory device to be renamed. 1. Selecting the Rename function Enter the USB menu (page 76). Press the e or f buttons to select the Rename function, then press the FUNCTION button. 5-3 Rename ≥Press[F] 2. Selecting the file to be renamed Press the c or d buttons to select the file to be renamed. Press the FUNCTION button. Rename MP3 Song 03 .MP3 3.
USB Menu 4 Delete The Delete function allows song and audio files stored on a USB memory device to be deleted. 1. Selecting the Delete function Enter the USB menu (page 76). Press the e or f buttons to select the Delete function, then press the FUNCTION button. 5-4 Delete ≥Press[F] 2. Selecting the file to be deleted Press the c or d buttons to select the file to be deleted, then press the FUNCTION button. Delete James'_song .MP3 3.
5 Format The Format function allows a USB memory device to be formatted, erasing all stored data. 1. Selecting the Format function Enter the USB menu (page 76). Press the e or f buttons to select the Format function, then press the FUNCTION button. 5-5 Format ≥Press[F] 2. Formatting the USB memory device A confirmation message will be shown in the LCD display, prompting to confirm the format operation. Format ? ≤No Yes≥ Press the e or f buttons to cancel or confirm the operation.
Power Troubleshooting Problem Possible Cause and Solution Page no. The instrument does not turn on. Check that the power cable is firmly attached to the instrument, and connected to an AC outlet. pp. 12 Check that the MASTER VOLUME slider is not set to the lowest position. pp. 13 Check that a pair of headphones (or headphone adaptor plug) are not connected connected to the PHONES jack. pp. 13 Check that Local Control is enabled in the MIDI Settings menu. pp.
PIANO 1 HARPSI & MALLETS Concert Grand Harpsichord Concert Grand 2 Harpsichord 2 Studio Grand Vibraphone Studio Grand 2 Clavi Mellow Grand Marimba Mellow Grand 2 Celesta Jazz Grand Harpsichord Oct* Jazz Grand 2 Bell_Split* PIANO 2 STRINGS Pop Piano Slow Strings Pop Piano 2 String Pad Modern Piano Warm Strings Rock Piano String Ensemble Honky Tonk* Soft Orchestra New Age Piano* Chamber Strings* New Age Piano 2* Harp New Age Piano 3* Pizzicato Str.* E.
Demo Song List No. Sound Song Composer 1 Concert Grand Liebesträume No.3 Liszt 2 Concert Grand 2 Petit chien Chopin PIANO 1 3 Studio Grand Original KAWAI 4 Studio Grand 2 Original KAWAI 5 Mellow Grand Sonata No.30 Op.109 Beethoven 6 Mellow Grand 2 La Fille aux Cheveux de Lin Debussy 7 Pop Piano Original KAWAI 8 Modern Piano Original KAWAI 9 Rock Piano Original KAWAI Original KAWAI PIANO 2 10 New Age Piano 2 (CA93) ELECTRIC PIANO 11 Classic E.
section Drum Rhythm List No.
Program Change Number List Sound type Multi-timbral mode = off/on1 Program number CA93 CA63 Multi-timbral mode = on2 Program number Bank MSB LSB PIANO 1 Concert Grand 1 1 1 121 0 Concert Grand 2 2 2 1 95 16 Studio Grand 3 3 1 121 1 Studio Grand 2 4 4 1 95 17 Mellow Grand 5 5 1 121 2 Mellow Grand 2 6 6 1 95 18 Jazz Grand 7 7 1 95 8 Jazz Grand 2 8 8 1 95 19 Pop Piano 9 9 2 95 10 Pop Piano 2 10 10 2 95 13 PIANO 2 Modern Piano 11 11 2 121 0
Sound type Multi-timbral mode = off/on1 Program number CA93 CA63 Multi-timbral mode = on2 Program number Bank MSB LSB HARPSI & MALLETS Harpsichord 41 31 7 121 0 Harpsichord 2 42 32 7 121 3 Vibraphone 43 33 12 121 0 Clavi 44 34 8 121 0 Marimba 45 35 13 121 0 Celesta 46 36 9 95 1 Harpsichord Oct* 47 - 7 121 1 Bell_Split* 48 - 15 95 5 Slow Strings 49 37 45 95 1 String Pad 50 38 49 95 8 STRINGS Warm Strings 51 39 49 95 1 String Ensemble 52
Connecting to Other Devices Audio equipment or electronic instruments Connect the instrument to external speakers, amplifiers, mixers, etc. Connect the stereo outputs from other electronic instruments or audio equipment to the instrument’s speakers. B pin Connect the instrument to a computer to exchange MIDI data. A pin Connect the instrument to external MIDI devices.
LINE IN jacks (1/4” phone jack) LINE IN STEREO jack (1/8” mini jack) These jacks are used to connect a pair of stereo outputs from other electronic instruments or audio equipment to the instrument’s speakers. The audio signal from these jacks bypasses the MASTER VOLUME control, however the the LINE IN level can be adjusted using the adjustment knob, or by adjusting the output level of the connected device. To connect a device in mono, connect the cable to the L/MONO jack only.
section Instructions (CA63 only) Assembly Please read these assembly instructions thoroughly before attempting to assemble the CA63 digital piano. Please ensure that two or more people work on assembling the CA63 digital piano, especially when lifting the main body of the instrument onto the stand in step 3. Included parts Before attempting to assemble the CA63 digital piano, ensure that all parts below are included.
2. Attaching the back board d Allow the assembled pedal board and side panels to stand upright (vertically) on the floor. Insert the back board d into the grooves of the side panels. d From the front, secure the top of the back board to the side panels using the four short black screws g. From behind, attach the bottom of the back board to the pedal board using the four long black tapping screws h.
Assembly sectionInstructions (CA63 only) 4. Connecting the pedal and power cables Pass the pedal cable (extending from the back of the pedal board) behind the back board, and through the aperture to the front of the main body. Connect the pedal cable to the PEDAL terminal on the base of the main body, ensuring the notched plug faces the rear of the instrument. When disconnecting the pedal cable, press and hold the notch and pull the plug gently.
section Specifications CA63 88 wooden keys RM3 Grand action with Ivory Touch and Let-Off 88 wooden keys RM3 Grand action with Ivory Touch Sound Source Ultra Progressive Harmonic Imaging™ (UPHI) Internal Sounds 80 voices 60 voices Polyphony max.
section MIDI Implementation Chart KAWAI CA93 / CA63 Date : Aug ’09 Version : 1.0 Function Transmit Receive 1 1 1 - 16 1 - 16 Mode 3 Mode 1 ° Mode 1, 3** ÄÄÄÄÄÄÄÄÄ ° 21 - 108* 0 - 127 ÄÄÄÄÄÄÄÄÄ 0 - 127 Note on { 9nH v=1-127 { Note off ° 9nH v=0 ° Key specific ° ° Channel specific ° ° ° ° 0.
Appendix section Notes 95
CA93/CA63 Owner’s Manual KPSZ-0298 : 816622 OW1030E-J1009 Version 1 Printed in Indonesia Copyright © 2009 KAWAI Musical Instruments Mfg. Co.,Ltd. All Rights Reserved.