COMPONENT #840 0646 19.2V BATTERY-OPERATED WORKLIGHT INSTRUCTION MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
TABLE OF CONTENTS CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION ONE RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . . . . . 2-3 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BATTERY TOOL USE AND CARE . . . . . . . . . . . . . . . . . . . . . . . . . . 4 SERVICE . . . . . . . . . . . . . . . .
CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. BATTERY TOOL USE AND CARE CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage. Ensure the switch is in the off position before inserting batter y p a c k . Inserting the battery pack into power tools that have the switch on invites accidents.
FUNCTIONAL DESCRIPTION information. If unreadable or missing, contact Alltrade for a replacement. 7 Batter y pack must be recharged only with the specified charger for the bat ter y. A charger that may be suitable for one type of battery may create a risk of fire when used with another battery. 5 8 Do not use in a damp or wet environment. Store out of reach of children and other untrained persons. 6 3 SYMBOLS IMPORTANT: Some of the following symbols may be used on your tool.
BATTERY Before using batter y pack, please read carefully all instructions and cautionar y markings on batter y pack, batter y charger and product using batter y. ® Do not incinerate the batter y pack even if it is severely dam aged or is completely worn out. The battery pack can explode. Do not carr y b a t t e r y p a c k s i n a p r o n s , p o c k e t s , o r t o o l b o x e s , p r o d u c t k i t boxes, drawers, etc. with loose metal objects.
CHARGING BATTERY PACK ADJUSTING THE WORKLIGHT BEAM BATTERY PACK CHARGE BATTERY PACK: 1. Make sure the trigger on the Cordless Worklight is in the “ O F F ” position and remove the battery pack from the Cordless Worklight. 120V AC ADAPTER 2. Plug 120V AC Adapter into household outlet and into side of battery charger. Insert battery pack into battery charger. When the battery is placed in the charger, the red LED indicator light will remain on. Hold the handle of the Worklight securely in one hand.
1. Remove the battery pack from the Worklight. REPLACEMENT BULB 2. Hold the top of the Worklight with one hand while twisting the rim in a counter-clockwise direction with the other. Continue turning until the rim comes loose. ACCESSORIES Use only accessories that are recommended by the manufacturer for your model. Accessories that may be suitable for one tool may become hazardous when used on another tool. Always attach grounded (3-prong) extension cords to grounded (3-hole) outlets. 3.
OTHER CONSUMER DO-IT-YOURSELF (DIY) TOOLS Alltrade offers a full range of Kawasaki™ tools that make DIY jobs easy. If you would like further information on the following products, please contact Alltrade Customer Service Department at 1-800-590-3723.
Exclusions This warranty does not cover parts damaged due to normal wear, abnormal conditions, misapplication, misuse, abuse, accidents, operation at other than recommended pressures or temperatures, improper storage or freight damage. Parts damaged or worn by operation in dusty environments are not warranted. Failure to follow recommended operating and maintenance procedures also voids warranty.
COMPONENT #690084 19.2V BATTERY-OPERATED CIRCULAR SAW INSTRUCTION MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
TABLE OF CONTENTS CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION ONE GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS . . 2 RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WORK AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. WORK AREA CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Keep your work area clean and well lit. Cluttered work benches and dark work areas may cause accidents or injury. CAUTION used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.
PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operat ing a power tool. Do not use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelr y. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Avoid accidental starting.
Check the operation and condition of the lower guard spring. If the guard and the spring are not operating properly, they must be ser viced before use. Lower guard may operate sluggishly due to damaged parts, gummy deposits, or a buildup of debris. Lower guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts.” Raise lower guard by Retracting Handle. As soon as the blade enters the material, lower guard must be r e l e a s e d .
When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw backward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding. When restarting a saw in the work piece, center the saw blade in the kerf and check that teeth are not engaged into the material.
CONTROL FEATURES: BATTERY Before using batter y pack, please read carefully all instructions and cautionar y markings on batter y pack, batter y charger and product using batter y. ® BEVEL LEVELING KNOB This knob controls the beveling of your cut. DEPTH ADJUSTMENT KNOB This knob controls the depth of your cut. Do not incinerate the batter y pack even if it is severely damaged or is completely worn out. The battery pack can explode.
REMOVING / ATTACHING BATTERY PACK CHARGING BATTERY PACK REMOVE BATTERY PACK: 1. Press both release buttons on either side of the Cordless Circular Saw to release the battery pack. CHARGE BATTERY PACK: 1. Make sure the trigger on the Cordless Circular Saw is in the “ O F F ” position and remove the battery pack from the Cordless Circular Saw. 2. Pull battery pack free of Cordless Circular Saw. ATTACH BATTERY PACK: 1.
ATTACHING / REMOVING BLADE If the blade clamp screw will not loosen enough to allow blade installation, tap gently on the end of the wrench with a mallet until the clamp screw breaks free. ATTACHING THE BLADE: 1. Remove the battery pack. REMOVING THE BLADE: 1. Remove the battery pack. 2. Retract the lower guard (see Fig. 1). 2. Use the wrench to loosen the clamping screw while pressing down on the blade safety lock button (see Fig. 3 and Fig. 4). 3. Slip the blade into place (see Fig. 2). 4.
OPERATING THE CIRCULAR SAW Never tape the trigger switch down to provide continuous high speed. The tool may fail under such conditions causing fire or personal injury. The lock-off button helps prevent accidental starting. This button can be pressed from either side. • Put on eye protection. • Clear the saw of any foreign material. • Make sure the work piece is held securely in place. Hold smaller pieces in a vise or attach to the workbench with clamps.
MAINTENANCE AND CLEANING Always remove the batter y pack before attempting cleaning or maintenance. This Circular Saw is lubricated before it leaves the factor y. This lubrication should last for the life of the tool. No further lubrication is required. RECOMMENDED SIZES OF EXTENSION CORDS 120 VOLT AC 60 HZ TOOLS TOOL CURRENT RATING AMPERE 3-6 6-8 8-10 10-12 12-16 16-20 Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the casing.
2 YEAR LIMITED HOME USE WARRANTY Express and Exclusive Limited Home Use Wa r r a n t y t o O r i g i n a l R e t a i l B u y e r Alltrade Tools LLC (hereinafter "Alltrade") expressly warrants to the original retail purchaser of the accompanying KAWASAKI™ portable power tool and no one else all parts of the product (except those parts referred to below which are specifically excluded from such warranty (see Exclusions)) to be free from defects in materials and workmanship for a period of two years from origi
Warranty Disclaimers EXCLUSION AND DISCLAIMER OF ALL OTHER EXPRESS WARRANTIES, GUARANTIES AND/OR REPRESENTATIONS.
COMPONENT #691234 19.2V 2-SPEED BATTERY-OPERATED DRILL INSTRUCTION MANUAL THIS MANUAL CONTAINS IMPORTANT INFORMATION REGARDING SAFETY, OPERATION, MAINTENANCE AND STORAGE OF THIS PRODUCT. BEFORE USE, READ CAREFULLY AND UNDERSTAND ALL CAUTIONS, WARNINGS, INSTRUCTIONS AND PRODUCT LABELS. FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY AND/OR PROPERTY DAMAGE.
TABLE OF CONTENTS CONGRATULATIONS! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 INTENDED USE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SECTION ONE GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS . . 2 RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS . . . . . . . . 2-3 IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 WORK AREA . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. WORK AREA WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Keep your work area clean and well lit. Cluttered work benches and dark work areas may cause accidents or injury. CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
PERSONAL SAFETY Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Avoid accidental starting.
SPECIFIC SAFETY RULES AND/OR SYMBOLS Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator. SAFETY RULES FOR CORDLESS DRILL / DRIVERS Always wear safety goggles or eye protection when using this tool. Use a dust mask or respirator for applications which generate dust.
FUNCTIONAL DESCRIPTION BATTERY 9 6 Before using battery pack, please read carefully all instructions and cautionary markings on battery pack, battery charger and product using battery. 8 7 ® 10 5 12 14 Do not carry battery packs in aprons, pockets, or tool boxes, product kit boxes, drawers, etc. with loose metal objects. Battery pack terminals could be short circuited causing damage to the battery pack, severe burns or fire. 13 11 4 3 2 1 CONTROLS AND COMPONENTS: 1. Battery Pack 2.
REMOVING/ATTACHING BATTERY PACK REMOVE BATTERY PACK: 1. Press both release buttons on either side of the Cordless Drill to release the battery pack. CHARGING BATTERY PACK 2. Pull battery pack free of Cordless Drill. ATTACH BATTERY PACK: 1. Align the raised portion of the battery pack with the groove in the battery compartment of the Cordless Drill. 2. Press the battery pack into place. Make sure the latches are securely fastened. Do not use the Cordless Drill if the battery pack is not seated properly.
INSTALLING DRILL BIT INTO KEYLESS CHUCK WARNING Before inserting a drill bit or other accessory, make sure the forward/reverse and trigger lock lever is in the center “OFF” position to prevent accidental starts that may result in injury. Do not attempt to tighten drill bits (or any other accessory) by gripping the front of the chuck and turning the tool on. This may cause personal injury and/or damage to the chuck.
TORQUE SETTINGS SCREWDRIVING To prevent damaging the tool or driving screw too deep into work piece, release the trigger when you feel the clutch slip. THE CONTROL RING ADJUSTS THE LEVEL OF TORQUE: • For light duty work, use lower settings. CONTROL RING WHEN DRIVING FASTENERS: • Always start slowly and gradually increase the speed of the Drill. • Release the trigger when you feel the clutch slip. • Always keep the driver bit straight to prevent damage to the screw.
• Just before the drill tip breaks though the other side of the work piece drill more slowly and decrease pressure on the tool. This will prevent stalling and leave a cleaner hole. • Use a block of wood to back up work pieces that may splinter. • Use spade bits when drilling large diameter holes in wood. Regularly clean the ventilation slots in your tool and charger using only a soft brush or dry cloth. Never open the Cordless Drill case, battery pack or charger.
SPECIFICATIONS SPECIFICATIONS Voltage No Load Low Speed No Load High Speed Torque Settings Chuck Capacity Charger Input Charging Time Battery Type 19.2V 0-400/min. 0-1100/min. 24+1 Drill Up to 10mm (3/8") 120V 60Hz Approx. 3-5 hours Ni-Cad PROTECTING THE ENVIRONMENT BATTERIES Alltrade batteries can be recharged many times. At the end of their useful life, recycle batteries with due care for our environment. Ni-Cad and Ni-MH batteries are recyclable.
conforming item and/or part thereof shall constitute fulfillment of all obligations to the purchaser. Alltrade shall not be responsible or liable for any expense, including freight charges, or repairs made outside Alltrade’s facility, unless expressly agreed to by Alltrade in writing. Under no circumstances shall Alltrade bear any responsibility for loss of the unit, loss of time or rental, inconvenience, commercial loss or consequential damages.