® PORTABLE FILTER OW N E R S M A N UA L M O D E LS P C 1 4 , LB - 1 0 0 , LB - 1 6 5 , LB - 2 0 0 This Owner’s Guide provides specific operating instructions for your model. Use the Portable Filter only as instructed in this Service Guide. 1-800-KEATING www.keatingofchicago.
READ AND SAVE THIS MANUAL FOR FUTURE REFERENCE Record the Model No. and Serial No. of this Portable Filter in the space provided below. Serial No. ____________________________________________________________ Model No. ____________________________________________________________ Keep these numbers for future reference IMPORTANT: Keep a copy of your bill of sale. The date on the bill establishes the warranty period should service be required.
PORTABLE FILTER OPERATING INSTRUCTIONS A. PREPARING THE PORTABLE FILTER 1. Remove screen from over tubes/element with tongs or a Drain Clean Out Rod (See Figure 1.1). SCREEN OVER TUBES/ ELEMENTS WILL BE VERY HOT AND SHOULD BE MOVED TO A SAFE PLACE. 2. Heat fryers to 325°F. Stir oil thoroughly until all water is removed and shut fryer off (including pilot light) before filtering. (Figure 1.2) NOTE: Water settles in the cooler oil in the Cold Zone.
C. CLEAN-UP FILTER UNIT AND PIPES WILL REMAIN HOT FOLLOWING FILTRATION. ALLOW THE UNIT TO COOL DOWN BEFORE CLEAN UP. FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY TO THE OPERATOR. Figure 2.1: Drain fryer 1. 2. 3. 4. 5. 6. Turn off filter and disconnect from electrical source. Remove strainer basket and hold down ring for cleaning Remove and discard filter paper and any residue. Clean filter tub thoroughly. Coat inside of pump with oil if water has been running through it.
SELF-HELP GUIDE PROBLEM Motor runs but will not pump oil. Motor does not operate. PROBABLE CAUSE SOLUTION (Follow Sequentially) A. Solidified shortening may have plugged pipes. Turn on fat melter for 20 minutes. This will heat filter tub and pipes to free system of solidified shortening. Reset motor before attempting filtering (reset button is located on rear of pump motor). B. Tub not set up properly. Place components in tub per the following: A. Not plugged in. B. Motor has overheated. C.
SERVICE DISASSEMBLY You will need: Adjustable wrench Standard pliers Replacement: 1. Connect tagged electrical leads to replacement switch. “Stubby” screwdriver Standard screwdriver 2. Insert replacement switch through panel from which defective switch was removed. Insert nameplate over toggle and secure to panel with nut supplied with switch. Orient switch and tighten nut to secure in desired position. 3.
SERVICE (continued) E. HEATER ELEMENT(S) 4. Remove attaching screws securing front panel. Tilt back front panel to expose pump and motor. Removal: 1. Disconnect filter from electrical power source. 5. Remove motor junction box cover and remove electrical leads from motor terminals. Tag leads as they are disconnected to assure, during replacement, they are reconnected to proper terminals. 6.
SERVICE (continued) I. HEAT TAPE Removal: 1. Disconnect filter from electrical power source. NOTE: Remove all oil from filter vessel. Filter must be positioned on its end to access heat tape. 2. Raise front (power cord) end of filter and rest filter on oil absorbing rags on its back end. 3. Remove bottom cover attaching screws; remove bottom cover. 4.
PORTABLE FILTER PARTS LIST Parts - LB100 Model Caster 3” swivel Caster 3” rigid Cover for LB-100 (2000 series) Cover for LB-100 (optional) (pre 2000 series) Filter screen LB-100 12 1/4” diameter Indicating Light - Amber Indicating Light - Red Handle for cover Heat Plate 500W 115V Heat Wrap Tape 4 ft. for LB and PC filters Hi-Limit Sensor Hold down Ring Handle Hold down Ring LB-100 Hold down Ring LB-100 (after 1/2003) Hose 4 ft.
PORTABLE FILTER PARTS LIST Parts - LB165 Model (continued) Strainer Basket LB165 Switch (Pump-off-melt) Switch Reversing (2-Way Pump) Terminal Block Terminal Board Terminal Board Insulation 000677 000521 000527 002065 000639 000263 Parts - LB200 Model Caster 3” swivel Cover for LB200 Handle for cover Heat Plate 500W 115V Heat Wrap Wire 4 ft. 100W 120V Hi-Limit Sensor Hold Down Ring (after 2004) Hold Down Ring (pre 2000) Hold Down Ring (pre 2003) Hose 5 ft.
LB100, LB165, LB200 1 Way Pump - Part # 008196 LB100, LB165, & LB200 2 Way Pump - Pump Part # 055173 (1988 - 2002) 9
LB165 & LB200 1 Way Pump (model 2004 series) - Pump Part # 055173 LB165 & LB200 1 Way Pump (after 2005) - Pump Part # 055173 10
LB165 & LB200 1 Way Pump (model 2003 series) - Pump Part # 052982 LB165 & LB200 2 Way Pump - Pump (after 2004) - Pump Part # 055173 11
LB200 1 Way Pump - Pump Part # 010567 (1993) LB200 2 Way Pump - Pump Part # 010567 (1993) 12
PC14 13
LIMITATIONS OF LIABILITY 100% 80% 60% 40% 20% 10% KEATING OF CHICAGO, INC., 1-800-KEATING WWW.KEATINGOFCHICAGO.COM KEATING REFILE/warranty 3/01 All repair services under this Limited Warranty must be authorized by Keating or performed at Keating. Authorization may be obtained by calling 1-800-KEATING within the Continental United States, Alaska, Hawaii, Puerto Rico and Canada during normal business hours (8:00 a.m. through 5:00 p.m. Central Time, Monday through Friday).
SERVICE INFORMATION If you have a service related question call 1-800-KEATING. Please state the nature of the call; it will ensure speaking with the appropriate person. Have your serial and model number available when ordering parts. KEATING OF CHICAGO, INC. 8901 West 50th Street, McCook, Illinois 60525-6001 Phone: (708) 246-3000 FAX: (708) 246-3000 Toll Free 1-800-KEATING (In U.S. and Canada) www.keatingofchicago.com *As continuous product improvement occurs, specifications may be changed without notice.
