User Manual
Table Of Contents
- 1. Introduction
- 2. General Information
- 3. In the Box and Unpacking
- 4. Setting Up LS50 Wireless II
- 5. Connection and Control Interface
- 6. Wi-Fi Streaming
- 7. Multi-Room Streaming
- 8. Voice Control Over Mobile Device
- 9. Playback with Bluetooth
- 10. Playback with HDMI eARC input
- 11. Playback with Optical Input
- 12. Playback with Coaxial Input
- 13. Playback with Auxiliary Input
- 14. Using KEF Connect App
- 14.1 Home
- 14.2 Remote Control
- 14.3 Music Content
- 14.3.1.1 Amazon Music
- 14.3.1.2 Deezer
- 14.3.1.3 Qobuz
- 14.3.1.4 Spotify
- 14.3.1.5 Tidal
- 14.3.1.6 Internet Radio
- 14.3.1.7 Podcast
- 14.3.2.1 Playback Screen
- 14.3.2.2 Search
- 14.3.2.3 Favourites
- 14.3.2.4 Queue (coming soon)
- 14.3.2.5 Playlists
- 14.4 Equalisations
- 14.5 Profile
- 14.6 Choosing Your Speaker
- 14.7 Speaker Preferences
- 14.8 Volume
- 14.9 Firmware Upgrade
- 14.10 Application
- 14.11 Support
- 15. Cleaning and Maintenance
- 16. Disposal
- 17. FAQ and Troubleshooting
- 18. Appendix
87
Table of ContentsSetting UpWi-Fi StreamingUsing KEF Connect AppFAQ and Troubleshooting
7. There is dropout from the Secondary Speaker.
•If the speakers are connected wirelessly, try to move them closer to each other.
•If the problem persists, connect the speakers with the inter-speaker cable and turn on
Cable Mode in the KEF Connect App.
8. The audio is out of sync with the picture when using LS50 Wireless II with a TV.
•If available, try the video delay/lip sync function of your TV.
9. I have connected the speakers to the TV with an HDMI cable, why is there no
sound?
•Make sure the source is switched to TV for the speakers.
•Check the TV icon on the top panel of the Primary Speaker.
If the TV icon is blinking, the HDMI connection is not found. In this case, make sure
that the HDMI cable is connected to the eARC or ARC port of the TV.
If the TV icon is pulsing (fade in/fade out), only CEC (not ARC) connection is
established (TV may respond without sound). In this case, do the following:
•The HDMI CEC connection needs to be enabled on the TV. As manufacturers
may name this connection differently (e.g. Anynet+ for Samsung, Simplink for LG),
please check the user manual of your TV on how to turn on HDMI connection for
your TV. Once the HDMI CEC connection is enabled, the TV icon on the top panel
should turn solid (both CEC and ARC connections are now established).
•If there is only no sound but everything else is working, please make sure that the
audio output of HDMI is set to PCM (this is often set to Dolby Digital by default).
As the settings menu of each TV manufacturer is different, please refer to the user
manual of your TV.
•For HDMI eARC input, make sure the connecting HDMI cable is of high speed with
Ethernet to provide sufficient bandwidth and speed.
•Change the HDMI cable (our internal tests found that HDMI cables of lower quality
may not be able to establish the connection).
•If the problem persists, please report the issue in the Support section of the KEF
Connect App for investigation. In the meantime, use the Optical connection as a
fall-back solution.
10. I have connected the speakers to the TV with an optical cable, why is there no
sound?
•Make sure your TV is set to output digital audio in PCM format.
•If the problem persists, try a different optical cable or connection option (e.g. HDMI).