Blade ow n e r ’s m a nu a l
impor tant safety information Thank you for purchasing KEF Blade speakers. They have been designed to faithfully reproduce high quality sound over many years of use and should provide realistic reproduction of music and speech. Please take a little time to read these instructions prior to use. Your KEF Blade speakers are tall, slim and extremely heavy. Installed correctly on a smooth, level surface, your speakers should be entirely safe to listen to and to live with.
contents Specifications Page 10 - unpacking, handling and after care Page 14 - amplifier to speaker connections Page 11 - adjusting the feet and/or spikes Page 15 - amplifier requirements and power handling Page 12 - speaker placement and room acoustics Page 16 - single, bi-wire and bi-amp connections Page 19 Page 7 Installation and Operation
Page 9
Installation and operation unpacking, handling and after care These Blade speakers are packed one speaker per carton. Prior to unpacking, please ensure that the serial numbers of the speakers supplied match each other. Then, unpack the speakers carefully following the instructions printed on the carton and inspect for any sign of damage. Your speakers left KEF in perfect condition. If any damage is apparent, you should notify your retailer or consultant immediately.
Installation and operation speaker placement and room acoustics Positioning the speaker in a corner or near to a side wall is not recommended as the significant bass boost caused by this position will affect the sound and cause the stereo image to deteriorate. It is best to place the speakers symmetrically within the room, relative to the walls, ceiling and floor, where possible.
Installation and operation amplifier to speaker connections All connections should be made with the amplifier switched OFF. Ensure the integrity of all connections prior to switching the amplifier ON. KEF Blade speakers are fitted with purpose designed silver-plated Bi-wire/Bi-amp terminals which will accept bare wire, spade or 4mm connectors. Most good quality speaker cables have some indication, such as colour coding or ‘ribbing’ on the insulating material, indicating which conductor is ‘+’ or positive.
Installation and operation single, bi-wire and bi-amp connections LIN LIN Single LIN LIN Bi-wire BLADE BLADE LIN HF LINK LINK LF BLADE LF LIN HF HF LINK LINK LF LF Bi-amp Speaker cables. Poor quality cables can seriously compromise the overall sound of your hi-fi system. KEF recommends that high quality speaker cable be used for connecting your Blade speakers. It is good practice to keep the cables as short as possible.
specifications Blade Design Three-way bass reflex, Single Apparent Source driver configuration Drive units Uni-Q driver array: MF: 125mm (5in.) Li-Mg-Al /LCP hybrid cone HF: 25mm (1in.) Al dome Bass units: LF: 4 x 225mm (9in.) with force cancelling Frequency response 40Hz - 35kHz +/- 3dB 28Hz - 45kHz. +/- 6dB Harmonic distortion 2nd and 3rd harmonics (90dB/1m): <0.5% 40Hz - 100kHz <0.2% 200Hz - 10kHz Crossover frequencies 350Hz, 3kHz Amplifier requirements 50 - 400W Sensitivity (2.
Page 21
www.KEF.com United Kingdom GP Acoustics (UK) Limited Eccleston Road, Tovil, Maidstone Kent, ME15 6QP U.K. Tel: +44 (0) 1622 672261 Fax: +44 (0) 1622 750653 Email: info@KEF.com China GP Acoustics (China) Limited Unit 4910, Diwang Commercial Centre Shenzhen, China 518008 Tel: +86 (755) 8246 0746 Fax: +86 (755) 8246 0125 Email: info.prc@gpe-hkg.com Europe (EMEA) GP Acoustics GmbH Am Brambusch 22, 44536, Lünen Deutschland Tel: +49 (0) 231 9860-320 Fax: +49 (0) 231 9860-330 Email: sales@gpaeu.