Instructions / Assembly

ManualsBrandsKelvin ManualsHeating, Ventilation, and Air ConditioningVoice Interactive 7 Day Programmable Thermostat

KELVIN



Installation Manual

Action Talking Products LLC

V1.5

Protected by U.S patent No. 5,690,277

Table of Contents

Getting Started ..............................................................................2

Compatabilty Chart........................................................................2

Mounting Instructions ....................................................................3

Wiring Diagrams............................................................................5

Quick Programming guide ............................................................7

Testing.........................................................................................11

Using KELVIN...........................................................................10

Advance settings .........................................................................11

Technical Information ..................................................................13

Summary of content (8 pages)

PAGE 1
Table of Contents KELVIN  Installation Manual Getting Started .............................................................................. 2 Compatabilty Chart........................................................................ 2 Mounting Instructions .................................................................... 3 Wiring Diagrams ............................................................................ 5 Quick Programming guide ............................................................
PAGE 2
Capability Chart Heating/Cooling system Gas or Oil -2, 4 or 5 wires Steam -Low voltage only (24VAC) Electric Baseboard -120 or 240VAC Heat pumps -Single stage or Multistage Compatible with KELVIN YES YES NO NO Mounting Instructions If you are replacing an existing thermostat please verify that the location fits the criteria below.
PAGE 3
Remove the old thermostat Make sure that the electricity to the heating and cooling system is turned off. Remove each wire one by one from the old thermostat. Make sure to label the wires (Rc, Rh, W, H, etc) so they can be connected to KELVIN correctly. Make sure that the wires do not fall into wall. You can wrap the wires around a pencil to stop them from falling into the wall. factory jumper between Rh and Rc.
PAGE 4
Wiring Diagrams 2/3 Wire Heat Only If only 2 wires exist then don't connect Fan Relay 5 wire Heating and Cooling If the Common wire doesn't exist then Install a jumper beween C and W If the Common wire doesn't exist then Install a jumper beween C and W Remove factory jumper between Rc and Rh C C G Fan Relay Y W Rc G Y W Rc Rh Rh Fan Relay Cooling Control Install factory Jumper across Rc and Rh Heating Control Heating Control 24VAC 24VAC 24VAC Cooling Transformer Common Transformer
PAGE 5
Quick programming guide 1) Insert 4 AA batteries (not included) into KELVIN as shown below. Setting the time. Open the door to expose the programming buttons. Press and hold the SET TIME button until the thermostat says “Set the time”. Use the up and down buttons to set the hour. Each press will change the hour by one. You can scroll through the hours more quickly if you disable the voice prompts by pressing the VOICE button.
PAGE 6
Setting the day Press the SET DAY button. The thermostat will advance one day for each press of the SET DAY button. Keep pressing the button until the correct day is reached. Testing KELVIN Snap the thermostat body onto the wall plate and set it to heat mode. Press the up button and raise the temperature at least 2 degrees more then the current temperature. Wait a minute or so and verify that your heat has turned on. You should hear a click when the thermostat enables the heating system.
PAGE 7
Advanced Settings Power Stealing Gas/Electric Setting If your have an electric system and the fan does not operate after the testing phase. You need to change the Gas/Electric jumper. To do this remove the thermostat from the wall and turn it over. On the back you will see a small opening. Put a jumper on J13, to connect the two pins. This will enable electric mode. Since this opening is very small you will probably need to use a pair of needle nose pliers or a tweezers.
PAGE 8
Technical Information Electrical Spec • 10-30 VAC • up to 1Amp (Max load for all terminals) Thermostat specs • Set point Range: 40°F - 90°F (4°C -32°C) • Operating Temp: 32°F - 105°F DO NOT USE WITH: • Heat pump systems • Systems Exceeding 50VAC and 1 Amp • Any 120 or 240VAC system WARRANTY, TECHNICAL SUPPORT, AND COPYRIGHT INFORMATION Action Talking Products LLC.