User's manual R KL72TT Twin-tub Washing Machine with Pump Contents Before using Names of the parts.............the 2nd cover Safety precautions ...............................1 Installation and adjustment ..................3 Introduction of the major functions .......5 Using process Preparation before washing ................6 The musts in washing .........................7 Usage of the detergent .......................8 Washing sequence ..............................9 Disposal after washing ...........
Names of the parts Before Using Buzzer Water-filling entrance Outer cover of the spin tub Water inlet selector handle Inner cover of the spin tub Wash selector Spin timer Wash timer Spin tub frame Control panel Spin tub Overflow filter Quick water-filling entrance Drain hose surpport Cabinet Water level adjusting lever Power cord Lint filter(installed by user) Pulsator Wash tub Drain hose Wash tub cover Base frame Meaning and description of the symbols Accessories Water-filling jointer (on
Safety precautions Please insert the power cord into special receptacle with rated voltage.Be sure to use single-phase three pins receptacle. The earthing terminal of the receptacle must be earthed reliably.If possible,please adopt electric leakage protector. Before Using The washing machine should be positioned so that the plug is accessible . Be sure to pull the plug off when there'spower failure, or the machine is being moved, cleaned or when it is idle.
Safety precautions Do not stretch hands into the working machine. It is dangerous even if the rotation is slow. Take special care of the children. Do not put any hot or heavy items ( such as the kettle with hot water ) on the washing machine. Before Using Do not decompose, repair or alter the machine by yourself. Do not wash laundries with volatile materials (such as thinner, petrol etc.). l Petro Handicapped or children without care shall not use the machine.
Installation and adjustment Before Using Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. The drainage shall be smooth with the drain hose. 1.The height of the drain hose shall be less than 1.2m , or the drainage will not be smooth enough and cause incomplete drainage. <1.2m 2.Do not step on or press the drain hose.
Before Using How to change the direction of the drain hoses Figure 1 indicates the ex factory installation position of the drain hose. Side sectional view Drain hose Fixing hook fixing hook installation hole Figure 1 Pull outwards slightly Extend the drain hose from the side of spin tub. Take off the drain hose from the hanging hole of the cabinet. Pull the drain hose fixing hook outwards gently to take out the drain hose from the two fixing hooks.
Introduction of the major function Using process The machine has good comprehensive performance, and nice appearance. It adopts streamline appearance and full plastic shell, which will never get rust. For the design on safety and reliability, it adopts the wash shelf, spin shelf and water reception groove design, and reduces the unfavorable influence on the electrical component by the vapor. Therefore it guarantees more safe and reliable washing.
Preparation before washing Using process Preparation before washing 1.Connect the water inlet hose. 2.Confirm that the washing machine is earthed reliably . Then insert the power plug into the receptacle. Do not connect the earth terminal to the gas pipe and tap water pipe. 3.Put the drain hose up to suitable position . 4.Slanting or uneven ground may result in unstable working or abnormal noise. Please make the machine stand horizontally.
Using process The musts in washing The capacity of washing and spinning of the machine refer to the largest weight of the standard laundries under dry condition that can be washed or spinned in one time. Laundries quantity in one washing cycle shall be lower than the rated capacity. The largest wash capacity of this machine is 7.2 kg, The largest spin capacity of this machine is 6.0 kg, The thickness ,size , type of the cloth will influence the actual washing capacity.
Usage of the detergent Using process How to use the whitener Fill water to decided level. Dilute the whitener with container. Pour it slowly into the washing tub. Avoid using whitener on laundries with color or pattern as they are prone to lose color. The whitener shall not touch the laundries directly. Refer to the user's manual for the usage and quantity of the whitener. For powder whitener, please dissolve it before using. How to use the washing powder Direct dissolved in the machine: 1.
Using process Washing sequence Water-filling selector handle Overfilling sign Wash timer (To set to below 2 minute, first set to 5 minute then turn it back. it can increase the service life of the timer). OFF Wash selector Water-filling entrance Buzzer Spin timer (The buzzer will ring when (to set to below 1 minute, the washing finishes) first set to 2 minute then turn it back. it can increase the service life of the timer).
Using process Midway spinning 1.Put the laundries into the spin tub evenly and smoothly. 2.Spin (1) Put the gland in properly. Please put in the gland properly even if the laundries quantity is small. Push Gland Push laundries Proper The are slanting Proper No gland (2) Close the inner and outer cover of the spin tub. (3) Spin for 1-2 minutes. Outer cover of The spin tub Inner cover of The spin tub 3.Run the foam-removing spinning. (1) Open the outer cover of the spin tub.
Using process Rinsing Rinse with water-filing 1.Put the laundries into the wash tub. Select suitable current according to the laundries. 2.Adjust the water level Set the water level with water level adjusting lever according to the laundries quantity. Then fill suitable water continuously. OVERFILL If you find water flowing out here,please twist the water tap to limit the water filling. 3.Rinse Adjust the wash timer to 5-7 minutes to do rinsing.
Using process Spinning Selection of the spin time 1. Put the laundries into the spin tub evenly and smoothly. 2. Press the gland in the tub properly. Close the inner and outer cover of the spin tub. 3. Spin Select suitable spin time according to the laundries, and do spinning.
Disposal after washing Using process After using, please clean the lint and foreign materials of the lint filter and overflow filter in time. Otherwise it may influence your using the machine. Please first pull off the power plug from the receptacle before cleaning. Cleaning the lint filter The lint filter must be used during washing. It must be cleaned in time after each using. 1. Take off the lint filter Put hand at the indicated position. Push down to take it off. ( See to Figure 1) Figure 1 2.
Using process Cleaning the overflow filter 2. Take off the corrugation pipe. Dismantle the upper part of the corrugation pipe inside the overflow filter ( as indicated in Figure 1). Water level adjusting lever 3. Cleaning the overflow filter Clean the lint around the filter and flush with tap water. Corrugation Pipe Figure 1 4. Install the overflow filter. (1).Install the corrugation pipe. (2).Insert the mounting plate at the bottom of the filter into original position. (3).
Trouble-shooting Answer to question If the laundries fall to the outer side of the spin tub If the laundries fall to the outer side of the spin tub, please take them out immediately. 1.Dismantle As indicated in the figure, push the point marked with " " to pull the spin tub frame to oblique upwards to dismantle it. Spin tub frame 2.Install After install the back edge of the spin tub frame to proper position, push the four points marked with " " by force to reset it. Please check carefully.
Trouble-shooting Answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. Do not repair it by yourself. Phenomena The machine does not act.
Packing list User's manual One Water inlet hose One Water-filling jointer One Gland One Lint filter One Twin-tub washing machine One
Specification Type Twin-tub washing machine with pump Model KL72TT Power source Rated voltage 220V~, Rated frequency 50Hz Water level Water quantity about Maximum/55L Medium/46L Minimum/36L Rated washing capacity kg 7.2 Rated spinning capacity kg 6.0 Rated input power W Wash 320 Spin210 Dimensions(mm) L810 Wash pattern New current Weight kg 27 Injection pressure 0.02MPa~0.
