Datasheet

ManualsBrandsKEMET ManualsAluminium Electrolytic CapacitorsRadial Electrolytic Capacitor, 220uF, 63VDC, 20%

1© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 • 864-963-6300 • www.kemet.com A4072_A759 • 11/29/2017

One world. One KEMET

Benets

• Through-hole form factor

• High voltage

• Low impedance

• High ripple current

• 125°C/2,000 hours

• RoHS compliant

Overview

KEMET’s A759 Single-Ended Conductive Polymer Aluminum

Solid Electrolytic Capacitors offer longer life and greater

stability across a wide range of temperatures. The A759

highly conductive solid polymer electrolyte eliminates the

risk of explosion from drying out and due to its low ESR

properties, is able to withstand higher ripple currents during

normal operation. The A759 is ideally suited for industrial

and commercial applications.

Applications

Typical applications include long life LED drivers,

professional power ampliers and industrial power supplies.

Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors

A759 125°C

Part Number System

A 759 BQ 106 M 1V AA E090

Capacitor

Class

Series Size Code

Capacitance

Code (pF)

Tolerance

Rated Voltage

(VDC)

Packaging ESR

A = Aluminum Single-Ended

Conductive

Polymer Solid

Capacitor

125°C

2,000 Hour

See Dimension

Table

First two digits

represent

signicant gures

for capacitance

values. Last digit

species the

number of zeros

to be added.

M = ±20% 6.3 = 0J

10 = 1A

16 = 1C

20 = 1D

25 = 1E

35 = 1V

50 = 1H

63 = 1J

80 = 1K

100 = 2A

160 = 2C

250 = 2E

See Ordering

Options Table

Last 3 digits

represent

signicant

gures for ESR

values.(mΩ)

Click image above for interactive 3D content

Open PDF in Adobe Reader for full functionality

Summary of content (16 pages)

PAGE 1
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Overview Applications KEMET’s A759 Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors offer longer life and greater stability across a wide range of temperatures. The A759 highly conductive solid polymer electrolyte eliminates the risk of explosion from drying out and due to its low ESR properties, is able to withstand higher ripple currents during normal operation.
PAGE 2
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Ordering Options Table Diameter Packaging Type Lead Type Lead and Packaging Code Lead Length (mm) Standard Bulk Packaging Options 5 – 18 Bulk (bag) 5 – 18 Bulk (bag) Bulk (bag) 5 – 18 Long Lead (Loose Standard Leads) Cut Leads Formed Leads 15 Minimum AA 5(1) 5(1) BA CA Standard Auto-Insertion Packaging Options 5–8 Ammo Tape and Box Ammo Tape and Box Formed to 2.5 mm Formed to 5 mm H0 = 16 ±0.5 H0 = 16 ±0.
PAGE 3
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Dimensions – Millimeters d P L Size Code 15 Minimum D 4 Minimum D L d P Nominal Tolerance Nominal Tolerance Nominal Tolerance Nominal Tolerance 5 6.3 8 8 10 10 10 10 13 18 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 11 11 8 12 12 16 18 20 20 31 ±1.0 ±1.0 ±1.0 ±1.0 ±1.0 ±2.0 ±2.0 ±2.0 ±2.0 ±2.0 0.5 0.5 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.8 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 ±0.5 2.0 2.5 3.
PAGE 4
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Impedance Z Characteristics at 100 kHz Z (−25°C)/Z (20°C) ≤ 1.25 Z (−55°C)/Z (20°C) ≤ 1.25 Compensation Factor of Ripple Current (RC) vs. Frequency Frequency 120 Hz ≤ f < 1 kHz 1 kHz ≤ f < 10 kHz 0.05 0.30 Coefficient 10 kHz ≤ f < 100 kHz 100 kHz ≤ f < 500 kHz 0.70 1.
PAGE 5
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Shelf Life & Re-Ageing The capacitance, ESR and impedance of a capacitor will not change significantly after extended storage periods, however, the leakage current will very slowly increase. • KEMET's conductive polymer aluminum solid electrolytic capacitors should not be stored in high temperatures or where there is a high level of humidity.
PAGE 6
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Table 1 – Ratings & Part Number Reference Rated Case Size Capacitance DxL 120 Hz 20°C (µF) (mm) ESR 100 kHz 20°C (mΩ) RC 100 kHz 105°C (mA) RC 100 kHz 125°C (mA) LC 20°C 2 minutes (µA) KEMET Part Number VDC VDC Surge Voltage 6.3 6.3 6.3 6.3 6.3 6.3 10 10 10 10 10 10 16 16 16 16 16 25 25 25 25 25 25 35 35 35 35 35 50 50 50 50 50 50 50 63 63 63 63 63 63 80 80 80 80 80 100 100 100 160 160 160 250 250 250 250 250 250 7.
PAGE 7
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Installing Conductive polymer aluminum solid electrolytic capacitors are prone to a change in leakage current due to thermal stress during soldering. The leakage current may increase after soldering or reflow soldering. Therefore, verify the suitability for use in circuits sensitive to leakage current. A general principle is that lower temperature operation results in a longer, useful life of the capacitor.
PAGE 8
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Expected Life Calculation Chart Expected life depends on operating temperature according to the following formula: L = Lo x 10(To-T)/20 Where: L: Expected life Lo: Life at maximum permissible operating temperature with rated operating voltage applied (hours) T: Actual operating temperature To: Maximum permissible operating temperature Expected Life Calculation Chart Lifetime vs Operating Temperature 125°C 115°C 105°C 95°C 85
PAGE 9
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Ultra Low Impedance at High Frequency Due to a solid polymer electrolyte, the curve of a conductive polymer electrolytic capacitor (Z and ESR) is significantly lower than that of a standard electrolytic capacitor. Ultra Low Impedance at High Frequency (Low ESR) 100 Impedance (Ω) Aluminum Electrolytic Conductive Polymer Electrolytic 10 1 0.1 0.
PAGE 10
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Construction Aluminum Can Lead Terminal Tabs Detailed Cross Section Rubber Seal Terminal Tab Rubber Seal Margin Aluminum Can Paper Spacer with Solid Polymer Electrolyte (First Layer) Paper Spacer with Solid Polymer Electrolyte (Third Layer) Anode Aluminum Foil, Cathode Aluminum Etched, Covered with Foil, Etched Aluminum Oxide (Fourth Layer) (Second Layer) Lead (+) Lead (−) © KEMET Electronics Corporation • P.O.
PAGE 11
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Marking Trademark Negative Polarity Blue Line Series Capacitance (µF) Rated Voltage (VDC) Flow Soldering (not suitable for SMD parts) The soldering conditions should be within the specified conditions below: • Do not dip the capacitors body into the melted solder. • Flux should only be applied to the capacitors' terminals. • Vapour heat transfer systems are not recommended.
PAGE 12
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Taping for Automatic Insertion Machines P2 P ∆h1 L H1 D F P1 H F1 Ho A W2 A W2 F1 Dimensions (mm) D Tolerance ±0.5 Formed to 2.5 mm 5 Formed to 5 mm Straight leads 10 - 13 mm 5 6.3 8-11 8 8.0 12.0 6.3 8-11 10 13 P D0 P2 P ∆h1 D H H1 d F P1 W2 A P1 P2 F W 8.0 12.0 12 16.0 18.0 20.0 20.0 0.5 0.5 12.7 12.7 5.1 6.35 2.5 12.7 12.7 3.85 6.
PAGE 13
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Construction Data Foil tabs The manufacturing process begins with the anode foil being electrochemically etched to increase the surface area and then ‘formed’ to produce the aluminum oxide layer. Both the anode and cathode foils are then interleaved with absorbent paper and wound into a cylinder. During the winding process, aluminum tabs are attached to each foil to provide the electrical contact.
PAGE 14
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Product Safety THESE NOTES SHOULD BE READ IN CONJUNCTION WITH THE PRODUCT DATA SHEET. FAILURE TO OBSERVE THE RATINGS AND THE INFORMATION ON THIS SHEET MAY RESULT IN A SAFETY HAZARD. Warning When potential lethal voltages e.g. 30 VAC (RMS) or 60 VDC are applied to the terminals of this product, the use of a hazard warning label is recommended. 1.
PAGE 15
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C Product Safety cont'd 4. Unsafe Use Most failures are of a passive nature and do not represent a safety hazard. A hazard may, however, arise if this failure causes a dangerous malfunction of the equipment in which the capacitor is employed. Circuits should be designed to fail safe under the normal modes of failure. The usual failure mode is an increase in leakage current or short circuit.
PAGE 16
Single-Ended Conductive Polymer Aluminum Solid Electrolytic Capacitors A759 125°C KEMET Electronics Corporation Sales Oﬃces For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change.