Datasheet
RoHS
Compliant
pHE850
• EMI suppressor, class Y2, metallized polypropylene
•
0.001 – 1.0 µF, 300 VAC, +110 °C
• New, small dimensions including low profile capacitors
tYpiCaL appLiCations ConstRuCtion
tECHniCaL data
The capacitors are intended for use as
interference suppressors in Y2 (line-to-
earth) applications.
Winding of metallized polypropylene.
Encapsulated in self-extinguishing material
meeting the requirements of UL 94V-0.
EnViRonmEntaL tEst data
Endurance EN/IEC 60384-14:2005 1.7 x U
R
VAC 50 Hz, once every hour
increased to 1000 VAC for 0.1 s,
1000 h at upper rated temperature
Vibration IEC 60068-2-6, Test Fc 3 directions at 2 hour each, No visible damage, No open or short circuit
10 – 55 Hz at 0.75 mm or 98 m/s
2
Bump IEC 60068-2-29, Test Eb 1000 bumps at 390 m/s
2
No visible damage, No open or short circuit
Change of temperature IEC 60068–2–14 Upper and lower rated No visible damage
Test Na temperature 5 cycles
Active flammability EN/IEC 60384-14:2005
Passive flammability EN/IEC 60384-14:2005
Humidity IEC 60068-2-3, Test Ca +40°C and 90 – 95% R.H. 56 days
L
H
B
p
l
∅ d
0.5
b
Rated voltage
Capacitance range µF
300 VAC, 50/60 Hz (ENEC,UL,cUL)
0.001–1.0
Temperature range °C –55/+110
Climatic category IEC 55/110/56/B
Capacitance tolerance ± 20% standard, other tolerances on request
Approvals ENEC, UL, cUL
Dissipation factor tanδ Maximum values at +23 °C
C ≤ 0.1 µF 0.1 µF < C ≤ 1 µF C > 1 µF
1 kHz 0.2% 0.15% 0.1%
10 kHz 0.3% 0.4% 0.8%
100 kHz 0.6% – –
Insulation resistance C ≤ 0.33 µF: ≥ 30 000 MΩ
C > 0.33 µF: ≥ 10 000 s
Resonance frequency Tabulated self-resonance frequencies f
0
refer to 5 mm
lead lengths.
Test voltage between The 100% screening factory test is carried out at 5000
terminals
VDC and 2500 VAC. The voltage level is selected to meet
the requirements in applicable equipment standards. All
electrical characteristics are checked after the test.
In DC applications Recommended voltage: ≤ 1250 VDC
p d std l max l b
10.0 ± 0.4 0.6 17 30 ±0.4
15.0 ± 0.4 0.6/0.8* 17 30 ±0.4
22.5 ± 0.4 0.8 6 30 ±0.4
27.5 ± 0.4 0.8 6 30 ±0.4
37.5 ± 0.5 1.0 6 30 ±0.7
* Size 7.5 x 14.5 x 18.0 and bigger, d = 0.8
mm.
Tolerance in lead length
< 30 mm mm
30 mm mm
+0
–1
+5
–0
Not for use in series with the mains.
See www.kemet.com for more information.