Datasheet

12© KEMET Electronics Corporation • KEMET Tower • One East Broward Boulevard T2043_T35X • 10/22/2018
Fort Lauderdale, FL 33301 USA • 954-766-2800 • www.kemet.com
Tantalum Through-Hole Capacitors – Radial Dipped
T350, T351, T352, T353, T354, T355 & T356 UltraDip II Polar
Figure 1
P
0
D
0
L
1
T
d
F
P
P
2
W
L
A
1
3
W
2
W
2
T
0
P
1
W
0
A
H
H
1
H
0
W
1
1
2
3
T396/98*
T350/51*
T352/53/56**
4
T354#
5
T355+
1 2
Carrier
Tape
1 mm
Maximum
(0.039”)
∆H
Dimension Symbol
Nominal
mm (inch)
Tolerance
mm (inch)
Body Height (1) A 17.0 (0.67) Maximum
Body Width (1) A
1
15.24 (0.600) Maximum
Sprocket Hole Diameter D
0
4.0 (0.157) ±0.3 (±0.012)
Lead Diameter d 0.51 (0.020) 0.64 (0.025) ±0.05 (±0.002)
Lead Center (4) F See Note Below
Component Base to Tape Center (4) H
C-7301
16.0 (0.630)
C-7303
18.0 (0.709)
C-7301
±0.5 (±0.02)
C-7303
Minimum
Lead Standoff Height H
0
C-7301
16.0 (0.630)
C-7303
18.0 (0.709)
C-7301
±0.5 (±0.02)
C-7303
Minimum
Component Height Above Tape Center H
1
32.25 (1.270) Maximum
Component Alignment Front to Rear ΔH 0 1.0 (0.039)
Cut Out Length L 11.0 (0.433) Maximum
Lead Protrusion L
1
1.0 (0.039) Maximum
Component Pitch (5) P 12.7 (0.500) ±1.0 (±0.039)
Sprocket Hole Pitch (2) P
0
12.7 (0.500) ±0.03 (±0.012)
Sprocket Hole Center to Lead Center (3) (4) P
1
See Note Below ±0.7 (±0.028)
Sprocket Hole Center to Component Center (5)
P
2
See Note Below
Body Thickness T
0
10.2 (0.400) Maximum
Total Tape Thickness T 0.7 (0.28) ±0.02 (±0.008)
Carrier Tape Width W 18.0 (0.709) +1.0/−0.5 (+0.039/−0.020)
Hold-Down Tape Width W
0
15 mm (0.561) 6 mm (0.236) +1.0/−0.8 (+0.039/−0.031
Sprocket Hole Location W
1
9.0 (0.354) +0.075/−0.5 (+0.030/−0.020)
Hold-Down Tape Location W
2
12.0 (0.472) Maximum
Notes:
(1) See Dimensions table for specic values per case size.
(2) Cumulative pitch error ± 1.0 mm (0.039) maximum in 20
consecutive sprocket hole locations.
(3) Measured at bottom of standoff.
(4) P
1
and F measured at egress from carrier tape.
(5) P and P2 measured at egress from carrier tape.
* Lead spacings are 2.5 mm (0.098") center to center (T350 A-H)
** Lead spacings are 5.0 mm (0.197") center to center
# Lead spacings are 6.35 mm (0.25") center to center
+ Lead spacings are 3.18 mm (0.125") center to center
F Dimensions: P
1
Dimensions:
0.100" ±0.015 Lead Spacing
0.125" ±0.015 0.100" – 0.200 ±0.028"
0.200" ±0.015 0.125" – 0.187 ±0.028"
0.250" ±0.015" 0.200" – 0.150 ±0.028"
0.100" ±0.015 (3 leaded) 0.250" – 0.125 ±0.028"
0.100" – 0.100 ±0.028" ( 3 leaded)