Datasheet

ManualsBrandsKEMET ManualsCapacitorsTantalum Capacitor 680 uF 6.3 VDC

One world. One KEMET

Benets

• Meets or exceeds EIA Standard 535BAAC

• Taped and reeled per EIA 481

• High surge current capability

• Optional gold-plated terminations

• High ripple current capability

• 100% surge current test

• 100% steady-state accelerated aging

• Capacitancevaluesof10μFto1,000μF

• Tolerances of ±10% and ±20%

• Voltage rating of 4 to 50 VDC

• Case sizes E and X

• ESRaslowas10mΩ

• RoHS Compliant and lead-free terminations

• Operatingtemperaturerangeof−55°Cto+125°C

Overview

The low ESR, surge-robust T510 is designed for demanding

applications that require high surge current and high ripple

current capability. This series builds upon the proven

capabilities of our industrial grade tantalum chip capacitors

to offer several advantages such as low ESR, high ripple

current capability, excellent capacitance stability, and

improvedresistancetohighin-rushcurrents.Thesebenets

are achieved though the utilization of multiple anodes as

well as high-stress, low impedance electrical conditioning

performedpriortoscreening.Thisseriesisclassied

as MSL (Moisture Sensitivity Level) 1 under J STD 020:

unlimitedoorlifetimeat≤30°C/85%RH.

Tantalum Surface Mount Capacitors – Low ESR

T510 Multiple Anode MnO

Applications

Typicalapplicationsincludedecouplingandlteringinindustrialandautomotiveendapplications,suchasDC/DC

converters, portable electronics, telecommunications, and control units requiring high ripple current capability.

Environmental Compliance

RoHS Compliant (6/6) according to Directive 2002/95/EC when ordered with 100% Sn solder.

Click image above for interactive 3D content

Open PDF in Adobe Reader for full functionality

Summary of content (15 pages)

PAGE 1
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Overview The low ESR, surge-robust T510 is designed for demanding applications that require high surge current and high ripple current capability. This series builds upon the proven capabilities of our industrial grade tantalum chip capacitors to offer several advantages such as low ESR, high ripple current capability, excellent capacitance stability, and improved resistance to high in-rush currents.
PAGE 2
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 K-SIM For a detailed analysis of specific part numbers, please visit ksim.kemet.com to access KEMET’s K-SIM software. KEMET K-SIM is designed to simulate behavior of components with respect to frequency, ambient temperature, and DC bias levels.
PAGE 3
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Qualification Test Condition Characteristics ΔC/C Endurance Storage Life Thermal Shock Temperature Stability Within initial limits DCL Within 1.25 x initial limit ESR Within initial limits ΔC/C Within ±10% of initial value 85°C at rated voltage, 2,000 hours 125°C at 2/3 rated voltage, 2,000 hours DF Within initial limits DCL Within 1.
PAGE 4
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Electrical Characteristics Capacitance vs. Frequency Impedance, ESR vs. Frequency 100 100 T510X226M035ATE100_IMP T510E476M035ATE050_IMP T510X226M035ATE100_ESR Capacitance (μF) Impedance, ESR (Ohms) T510X336M035ATE065_IMP 10 T510X336M035ATE065_ESR T510E476M035ATE050_ESR 1 10 T510X226M035ATE100 T510X336M035ATE065 0.1 T510E476M035ATE050 0.
PAGE 5
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Table 1 – Ratings & Part Number Reference Rated Rated Voltage Cap Case Code/ Case Size KEMET Part Number DC Leakage VDC @ 85°C µF KEMET/EIA (See below for part options) µA @ +20°C Max/5 Min 4 4 4 4 4 4 4 6.3 6.3 6.3 6.3 6.
PAGE 6
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Recommended Voltage Derating Guidelines 85°C to 125°C VR 67% of VR 50% of VR 33% of VR 120% 100% % Working Voltage % Change in Working DC Voltage with Temperature Recommended Maximum Application Voltage −55°C to 85°C 80% % Change in Working DC Voltage with Temperature 67% 60% 40% 20% 0% −55 Recommended Maximum Application Voltage (As % of Rated Voltage) 25 33% 85 Temperature (°C) 125 Ripple Current/Ripple Voltage Permis
PAGE 7
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Reverse Voltage Solid tantalum capacitors are polar devices and may be permanently damaged or destroyed if connected with the wrong polarity. The positive terminal is identified on the capacitor body by a stripe plus in some cases a beveled edge. A small degree of transient reverse voltage is permissible for short periods per the table. The capacitors should not be operated continuously in reverse mode, even within these limits.
PAGE 8
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Soldering Process Please note that although the X/7343–43 case size can withstand wave soldering, the tall profile (4.3 mm maximum) dictates care in wave process development. Hand soldering should be performed with care due to the difficulty in process control. If performed, care should be taken to avoid contact of the soldering iron to the molded case.
PAGE 9
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Construction Polarity Stripe (+) Molded Epoxy Case Detailed Cross Section Silver Paint (Fourth Layer) Polarity Bevel (+) Leadframe (− Cathode) Washer Tantalum Wire Tantalum Wire Weld (to attach wire) Carbon (Third Layer) Washer Silver Adhesive Leadframe (+ Anode) Molded Epoxy Case MnO2 (Second Layer) Ta2O5 Dielectric (First Layer) Tantalum Capacitor Marking Date Code * KEMET Multi-Anode MnO2 Polarity Indicator (+) 1 digit
PAGE 10
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Tape & Reel Packaging Information KEMET’s molded chip capacitor families are packaged in 8 and 12 mm plastic tape on 7" and 13" reels in accordance with EIA Standard 481: Embossed Carrier Taping of Surface Mount Components for Automatic Handling. This packaging system is compatible with all tape-fed automatic pick-and-place systems. Right hand orientation only (+) Embossed carrier (−) Embossment Top tape thickness 0.10 mm (0.
PAGE 11
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Figure 1 – Embossed (Plastic) Carrier Tape Dimensions P2 T T2 ØD0 P0 [10 pitches cumulative tolerance on tape ±0.2 mm] A0 E1 F K0 B1 E2 B0 S1 W P1 T1 Center Lines of Cavity B1 is for tape feeder reference only, including draft concentric about B0.
PAGE 12
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Packaging Information Performance Notes 1. Cover Tape Break Force: 1.0 kg minimum. 2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be: Tape Width Peel Strength 8 mm 0.1 to 1.0 Newton (10 to 100 gf) 12 mm 0.1 to 1.3 Newton (10 to 130 gf) The direction of the pull shall be opposite the direction of the carrier tape travel.
PAGE 13
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Figure 5 – Reel Dimensions Full Radius, See Note W3 (Includes flange distortion at outer edge) Access Hole at Slot Location (Ø 40 mm minimum) W2 D A (See Note) N C (Arbor hole diameter) B (see Note) (Measured at hub) W1 (Measured at hub) If present, tape slot in core for tape start: 2.5 mm minimum width x 10.0 mm minimum depth Note: Drive spokes optional; if used, dimensions B and D shall apply.
PAGE 14
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 Figure 6 – Tape Leader & Trailer Dimensions Embossed Carrier Punched Carrier 8 mm & 12 mm only END Carrier Tape Round Sprocket Holes START Top Cover Tape Elongated Sprocket Holes (32 mm tape and wider) Trailer 160 mm minimum Components 100 mm minimum Leader 400 mm minimum Top Cover Tape Figure 7 – Maximum Camber Elongated Sprocket Holes (32 mm & wider tapes) Carrier Tape Round Sprocket Holes 1 mm maximum, either direction Stra
PAGE 15
Tantalum Surface Mount Capacitors – Low ESR T510 Multiple Anode MnO2 KEMET Electronics Corporation Sales Oﬃces For a complete list of our global sales offices, please visit www.kemet.com/sales. Disclaimer All product specifications, statements, information and data (collectively, the “Information”) in this datasheet are subject to change.