User Manual

ManualsBrandsKen-A-Vision ManualsOffice ElectronicsCeilingDocCam 2 - Ceiling Mounted Document Camera

ProfCam by Ken-A-Vision

Ceiling DocCam™ II

Installation & Operation Manual

910-171-066

Troubleshooting

5615 Raytown Road • Kansas City, MO 64133 U.S.A.

Tel.: 816-353-4787 • Fax: 816-358-5072

email: flexcam@ken-a-vision.com • www.ken-a-vision.com

Problem Try this

No video image

The IR remote control

does not work

Can’t see an entire

drawing/page clearly

on the video screen.

Verify that the Cat. 5 is connected between the RJ-45 jack on

the back of the camera module enclosure and the RF-45 jack

on the back of the wall plate.

Make sure the provided 15 VDC power supply is plugged

into a wall outlet and the 15 VDC jack on the wall plate.

Check the S-video or composite cables to verify they are properly

connected, ensure video display device is powered and make

sure the display device is set to the correct video source

Verify fresh batteries are installed and positioned correctly.

Remove power supply plug from the 15 VDC jack on the wall

plate. Wait a few seconds and reinsert the power supply plug.

When large documents, such as blueprints, are being viewed,

the smallest details may not appear perfectly. The resolution

only allows zoomed in images to be clear. However, in viewing

normal size documents, details should be clear.

800-171-066

Summary of content (8 pages)

PAGE 1
ProfCam by Ken-A-Vision® Ceiling DocCam™ II Installation & Operation Manual Troubleshooting 910-171-066 Problem Try this No video image Verify that the Cat. 5 is connected between the RJ-45 jack on the back of the camera module enclosure and the RF-45 jack on the back of the wall plate. Make sure the provided 15 VDC power supply is plugged into a wall outlet and the 15 VDC jack on the wall plate.
PAGE 2
Table of Contents Table of Contents Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Services and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Operation Viewing areas Viewing area depends on the distance between the ceiling and the table. Use the following tables to determine the maximum and minimum viewing areas of the Ceiling DocCam™ II for distances of 5.5', 6.5' and 7.5'. (Most tables are about 2.
PAGE 3
Operation Introduction Operation Introduction Using your codec remote The only function you can control on the Ceiling DocCam™ II from your codec remote is the zoom in or zoom out. All other functions must be performed using the Ken-A-Vision® remote. Using your Ken-A-Vision remote The Ceiling DocCam™ II is a ceiling-mounted document camera that displays images on monitors, plasma screens, video projectors and videoconferencing systems.
PAGE 4
Introduction Installation Unpacking Cameras Programming presets Ensure that you received the following parts: Presets are used to program defined positions of the camera into a simple, one button preset. You can switch easily from a zoomed in position on a small document to a zoomed out position for documents such as blueprints. This saves the hassle of zooming in and out when presenting documents of a variety of sizes.
PAGE 5
Installation Introduction Configuring for remote controls Important safeguards The Ceiling DocCam™ II can be programmed to work with the remotes listed below. DIP switches on the camera enclosure must be configured in order to work with these remotes. See Figure 2 on Page 4 for exact location of DIP switches. Use the following diagram to program your Ceiling DocCam II correctly. • Read and understand all instructions before using.
PAGE 6
Introduction Installation Product overview Connecting cables Camera enclosure A single RJ-45 cable connects to the back of the wall plate providing S-Video, composite video, power and RS-232 control. The front of the wall plate provides the break-out connections for S-Video, composite video, power and RS-232 control. The wall plate may be attached to a standard single gang wall box or placed in an equipment rack in a surface mount wall box. A 50' Cat.
PAGE 7
Installation Introduction To mount the camera Front and back wall plate connections 1. Attach a string or plumb bob to the ceiling tile with a thumb tack. 2. Position the string directly over ample table space or work surface to allow easy document and object position. B 15 VDC C Composite Video D S-Video See Figure 6 RS-232 E 3. Using a sharp utility knife, score a 3 1/2” diameter hole into the front of the tile centered on the string. 4. Cut out the 3 1/2” hole. Figure 6.
PAGE 8
Introduction Installation Remote M Installation PWR FLIP A L DISPLAY Before you install K B FREEZE AUTO FOCUS ZOOM IN C • String or plumb bob CAM LASER D The following equipment is needed for proper installation: • Utility knife ZOOM OUT J • Flathead screwdriver PRESETS E 0 1 2 3 4 5 Be sure to check above the ceiling tile where you plan to install the camera to make sure the area is clear and that there is enough room for the Ceiling DocCam™ II and all of its components.