Instructions / Assembly

ManualsBrandsKendal Lighting ManualsOtherRK30 Series 3-Light 4 ft. Satin Nickel Track Lighting Kit

*WARNING:RISK OF FIRE AND ELECTRIC SHOCK.THIS PRODUCT REQUIRES

PROPER FIELD WIRING AND IS INTENDED TO BE INSTALLED BY A QUALIFIED

ELECTRICIAN ONLY.

ITEM NO.: RK30

IMPORTANT SAFETY INSTRUCTIONS

Important:

When replacing Gu10 bulbs, be sure the Wattage of the bulb is 50W or less. Using higher wattage

bulb may damage the fixtures.

CAUTION:

To reduce the risk of fire, the bare conductors shall be installed a minimum 7 feet from the ground.

CAUTION:

Hot surface, keep away from curtains and combustible materials.

CAUTION:

Risk of burn, before energizing, ensure that the bare conductors are free from any metallic objects

not part of this lighting system.

When installing or using the lighting system, basic safety precautions should always be followed including the following.

1). Read all instructions.

2). Do not conceal or extend bus-bar conductors through a building wall.

3). Do not install this system in damp or wet locations. -

4). Do not install any part of this system less than 7 feet above floor.

5). To reduce the risk of fire and overheating, make sure all connections are tight.

6). To reduce the risk of fire and burns, do not install this lighting system where the uninsulated open bus-bar

conductors can be shorted or contact conductive materials.

7). Turn off electrical power before modifying the light system in any way,or during re-lamping.

Summary of content (5 pages)

PAGE 1
*WARNING:RISK OF FIRE AND ELECTRIC SHOCK.THIS PRODUCT REQUIRES PROPER FIELD WIRING AND IS INTENDED TO BE INSTALLED BY A QUALIFIED ELECTRICIAN ONLY. ITEM NO.: RK30 IMPORTANT SAFETY INSTRUCTIONS Important: When replacing Gu10 bulbs, be sure the Wattage of the bulb is 50W or less. Using higher wattage bulb may damage the fixtures. CAUTION: To reduce the risk of fire, the bare conductors shall be installed a minimum 7 feet from the ground.
PAGE 2
Caution: To reduce risk of fire, use only the type of lamp and maximum wattage marked on the fixtures Caution: To reduce risk of fire, do not use lamps identified for use in enclosed fixtures. Caution: Indoor use. Caution: Use only type GU10, rated 120 volts, 50W maximum. *Please inform your dealer immediately in case of any parts shortage. *Save these instructions for future reference. ITEM NO.: RK30 ASSEMBLY INSTRUCTIONS: Please carefully unpack and place all lamp parts on a flat surface.
PAGE 3
WARNING: TO PREVENT ELECTRICAL SHOCK TURN OFF POWER TO FIXTURE LOCATION AT MAIN BREAKER. Step2 : (1)Loosen set screw(I) and slide down canopy(G)(careful not to scratch finish). (2)Fasten cross bar (E) to junction box with screws(F). (3)Connect the Ground Wire from fixture to crossbar (E), connect the Ground Wire from outlet box to crossbar (E). Connect the wire (Neutral) from fixture to wire(Neutral) from power supply with the wire nut.
PAGE 4
ITEM NO.: RK30 Step3 : Remove cap(L) and open the adaptor half(J)of power feed,place rail(marked this side up) into adaptor making sure the two connector tabs are on the same side as the two rail connectors.Close adaptor and place cap on adaptor by lining up the indent on cap with the set screw on the adaptor,push down and tighten to lock in place. Step4 : Remove the fixture cap (N) from each fixture, slide the adapter onto the rail and secure the cap (N).
PAGE 5
A: Power Feed Connection B: Fixture Connections C: Ensure bulbs are Secure. Step6 : Check for loose connections. 1. Turn the power to electrical box on. 2. Turn on the system and let it run for 5 minutes turn the system off and be careful all connection points are not hot to the touch (warm is acceptable), if a connection is hot, be sure to firmly tighten the connection. A: Power Feed Connection. B: Fixture Connections. C: Ensure bulbs are Secure.