Manual

Grill Lighting Instructions
1. Before each use, check all hoses for cracks, nicks,
cuts, burns or abrasions. If a hose is damaged in any
way, do not use your grill before replacing the hose
with an authorized part from the Parts List. Also make
sure all gas supply connections are securely
tightened.
2. Familiarize yourself with the safety and Use and Care
instructions in this manual. Do not smoke while
lighting grill or checking gas supply connections.
3. Be sure the LP Gas tank is filled or the Natural Gas
Line is attached to the gas source.
4. Open the Grill Lid.
5. Check that the end of each Burner Tube is properly
located over each Valve Orifice.
Failure to replace a faulty hose, secure gas supply
connections or to open the Lid before proceeding
to the Lighting Procedures could result in a fire or
explosion that could cause serious bodily injury,
death, or property damage.
6. Set Control Knobs to OFF and open the LP Gas tank
valve SLOWLY 1/4 of a turn. For Natural Gas open
the Shut Off Valve at source.
| Open LP Gas tank
OFF
7. Push and turn the LEFT Control Knob to IGN. Push
the Control Knob in to automatically ignite the Burner.
|
HI IGN
OFF
Main Back Infrared
Burner Burner Sear Burner
8. If ignition does not occur in 5 seconds, turn the burner
Control Knob(s) and gas source OFF and conduct a
leak test of ALL gas connections and gas sources as
explained in the Use and Care section of this manual.
If no leaks are detected, wait 5 minutes for any gas to
clear and repeat the lighting procedure.
9. After one Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn for 1/2 of one complete turn.
10. Once one Burner is lit, the adjacent Burner can be lit
by turning its Control Knob to HIGH.
Back Burner Lighting Instructions
1. Follow steps 1 through 6 of the Grill Lighting
instructions.
2. Push and turn the Control Knob to IGN. Push the
Control Knob in to automatically ignite the Burner.
Once the burner is lit, turn the knob back to ON,
keep pressing the knob and holding it for at least
10 seconds before releasing.
3. If ignition does not occur in 5 seconds, turn the
Control Knob(s) and gas source OFF and conduct a
leak test as explained in the Use and Care section
of this manual. If no leaks are detected, wait 5
minutes for any gas to clear and repeat the lighting
procedure.
4. After Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn for 1/2 of one complete turn.
BACK BURNER KNOB: INFRARED BURNER KNOB:
|
IGN
OFF i O j
......... _' --OFF
Infrared Sear Burner Lighting Instructions
1. Follow steps 1 through 5 of the Grill Lighting
Instructions.
2. Open infrared Sear Burner Lid.
3. Set Control Knobs to OFF and open the LP gas
tank valve SLOWLY 1/4 of a turn. For Natural Gas
open the Shut Off Valve at source.
4. Push and turn the Control Knob to IGN. Push the
Control Knob in to automatically ignite the Burner.
Once the burner is lit, turn the knob back to High,
keep pressing the knob and holding it for at least
10 seconds before releasing.
5. If ignition does not occur in 5 seconds, turn the
burner Control Knob(s) and gas source OFF and
conduct a leak test as explained in the Use and
Care section of this manual. If no leaks are
detected, wait 5 minutes for any gas to clear and
repeat the lighting procedure.
6. After Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn for 1/2 of one complete turn.
Manually Lighting Your Grill By Paper Match
To light your Main Burner by match, follow steps 1 through
6 of the Grill Lighting instructions. Then, light the match
and place it over the top opening of the Lighting Tube.
Push and turn the nearest Control Knob to the HIGH
setting to release gas. The Burner should light
immediately.
Left Bowl Panel
19 Lighting Tube