Installation guide

ManualsBrandsKenmore Elite ManualsRoom air conditionerOfficial Kenmore Elite room air conditioner

READ BEFORE INSTALLING UNIT

For Low Profile Window Air Conditioner

To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp

edges that may be exposed:

Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to

move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

Carefully inspect location where air conditioner will be installed. Be sure it will support the weight of the unit over

an extended period of time.

Handle air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp

metal fins of front and rear coils.

Make sure air conditioner does not fall during installation.

• SAVE CARTON and these INSTALLATION INSTRUCTIONS for future reference. The carton is the best way to

store unit during winter, or when not in use.

o DO NOT USE ANY SCREWS OTHER THAN THOSE SPECIFIED IN THESE INSTRUCTIONS.

Tools Required

® SCREWDRIVER (Standard and Phillips and Flathead) o RULER

• KNIFE • HAMMER

o PENCIL • LEVEL

Hardware ( in plastic bag)

SUPPORT BRACKET

SHORT LEVELING BOLT 1

LONG LEVELING BOLT 1

1/2" SCREW

Qty.

Hardware ( in plastic bag)

SASH LOCK

WEATHER SEALS

(6"X3/4"X 1/12")

WINDOW SASH SEAL

FOAM STRIP

Qty.

2020211A2592

Summary of content (12 pages)

PAGE 1
READ BEFORE INSTALLING UNIT For Low Profile Window Air Conditioner To avoid risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed: Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving unit. Carefully inspect location where air conditioner will be installed.
PAGE 2
How to install the unit 1. To prevent vibration and noise, make sure the unit is installed securely and firmly. 2. Install the unit a little slanted so the back is slightly lower than the front (about 1/4"). This will force condensed water to flow to the outside. CAUTION: All side louvers of the cabinet must remain exposed to the outside of the structure. 7 [ ut 1/4" Install Left + Right Filler Panel Assembly Place unit on floor, a bench or a table.
PAGE 3
CuttheFOAMSTRIPtofit theunderside ofthewindowsash.Openthewindow,peeloffthe backandattach the FOAMSTRIPasshownin FIG.5 Markcenterlinewithpencilonthecenteroftheinnersill,asshownin FIG.6 FIG. 6 FiG. 5 FOAM STRIP CENTER LINE INNER SILL Install support bracket on window sill. See FIG.7. Install leveling bolt up through bottom side of support bracket. You can choose a short bolt or a long one according to window type. Also, you should select the position of hole on bracket.
PAGE 4
SECURE THE CURTAIN FRAMES: Expand the filler panels and secure them using 4 screws as shown in FIG.10. When filler panels opens or closes, you may feel a slight resistance. This is normal. WINDOW SASH SEALAND WINDOW LOCK: Cut the window sash seal to the window width. Stuff the window sash seal between the glass and the window to prevent air and insect from getting into the room, as shown in FIG.10.
PAGE 5
REMOVAL FROM WINDOW: Turn off and unplug the air conditioner. Unscrew the side screws that you installed in step 6 and 7. Close the filler panels and remove window sash seal and sash lock from windows. Keep a firm grip on the air conditoner as your sash. Lift the air conditioner from the window. Remove the support bracket from window frame. NOTE: When cooling season is over, unit is removed from window for cleaning and storage. There may still be some condensation water in the basepan.
PAGE 6
BLANKPAG
PAGE 7
LEA ESTO ANTES DE MONTAR LA UNIDAD Para Acondicionadores de Aire de Ventanas de Perfil Bajo Para evitar el riesgo de lesiones, de dados materiales y de dados al equipo debido a su peso y a los bordes afilados que puedan quedar expuestos: Los aparatos de aire acondicionado detallados en este manual suponen un peligro pot su excesivo peso. Es necesaria la intervenci6n de dos o mas personas para mover e instalar el equipo.
PAGE 8
C6mo instalar la unidad , , Para evitar la vibraci6n y el ruido, asegOrese de que la unidad est_ firmemente sujeta. Instale la unidad un poco inclinada de manera que la parte posterior este un poco m_s abajo que la parte anterior (m_s o menos 1/4"). Esto har_ que el agua condensada salga de la unidad. PRECAUClON: Todas las palas de direccionamiento del aire deben quedar expuestas en la parte de fuera de la carcasa.
PAGE 9
CortelaTIRADEESPUMA parequese ajustea laparteinferiordela hojadelaventana.Abrala ventana, quiteel protectoryfijelaTIRADEESPUMAcomoseindicaenla FIG.5. Marqueel centrodelantepecho conunlapizcomose muestraen laFIG.6. FiG. 6 FiG. 5 LINEACENTRAL ANTEPECHO INTERIOR Instale el soporte de montaje en el antepecho de la ventana. Ver FIG.7. Instale el perno de nivelaci6n hacia arriba a trav6s de la parte de abajo del soporte de montaje. Puede elegir entre el perno corto o el largo dependiendo de su tipo de ventana.
PAGE 10
BLOQUEE LOS MARCOS DE LOS PANELES DE RELLENO LATERALES: Expanda los paneles de relleno y bloqu6elos usando los 4 tomillos como se muestra en la FIG.10. Cuando los paneles de relleno se abren o se cierran puede encontrar cierta resistencia. Esto es normal. SELLADO DE LA HOJA DE LA VENTANA Y BLOQUEO DE LA VENTANA: Corte el burlete para la ventana para que se ajuste al ancho de la ventana. Introduzca el burlete entre el cristal y la ventana para evitar que entren el aire y los insectos, como muestra en la FIG.
PAGE 11
EXTRAER DE LA VENTANA: Apagar y desenchufar el acondicionador de aire. Desatornillar los tornillos laterales que instal6 en los pasos 6 y 7. Cierre los paneles de relleno y remueva el burlete de ventana y el bloqueo de ventana de la ventana. Sujete firmemente el acondicionador de aire y la hoja de la ventana. Levante el acondicionador de aire de la ventana. Quite el soporte de montaje del marco de la ventana.
PAGE 12
BLANK PAGE