Installation Guide

4
OPERATION
BLOWER ACTIVATION/SPEED LEVEL CHANGE/
FILTER INDICATOR RESET
When blowers are OFF, press on this push button to turn
ON the blowers at the last saved speed. If there was
no speed saved, the blowers will be set on LOW speed.
NOTE: When LOW speed is activated from OFF,
the blowers start on MEDIUM speed for a very
short lapse of time, and then resume to LOW
speed.
To change the blower speed, press on this push button
again until the desired speed is reached (from LOW to
MEDIUM to HIGH speed to OFF). Each time a blower
speed is activated, a rotating blower icon appears on
left side of LCD screen, with dot(s) under it (the rotation
speed shows the chosen speed: slow for LOW with
one dot, faster for MEDIUM with 2 dots and fastest for
HIGH with 3 dots).
When blowers are on (no matter the speed level),
press and hold this push button until the blower icon
disappears from the LCD screen; this will turn off the
blowers and save the blower speed chosen.
Heat Sentry™
This hood is equipped with a protective device that
activates the blowers when an abnormally high heat
level is detected while the blowers are activated. During
the Heat Sentry activation, this device takes control of
the blowers and set them on MEDIUM speed while all
dots under the blower icon blink. However, the lights can
be still controlled. The blowers will remain on MEDIUM
speed until the heat is back to normal, they then return
to the speed previously selected.
NOTE: When excessive heat is detected, Heat Sentry
will shut off both blowers and lights while all
dots under the blower icon will blink faster.
Both blowers and lights will remain off until the
ambient temperature cools down; the blowers
will then start on MEDIUM speed (the lights
can be controlled again). The blowers will remain
on MEDIUM speed until the heat is back
to normal, they then return to the speed
previously selected.
1
NOTE: At range hood start-up or after a power failure,
a small icon (1) appears shortly (for ± 2 seconds)
on LCD screen; this is normal.
DELAY OFF
When the blowers are on, press this button to activate
the delay function. This icon appears on LCD screen
beside the blower icon to indicate the function is on.
The blowers will continue to operate for 10 minutes and
then, will shut off automatically (both blower and delay
icons will disappear from LCD screen). When Delay off
is activated, it is possible to change the blower speed
by pressing on blower push button without aff ecting the
remaining time of the delay.
To cancel the delay off function before the end of the
10-minute cycle, press again on delay off push button.
OPERATION
ON LIGHTING/LIGHT INTENSITY CHANGE
Press this push button to turn on the lights at the last
saved intensity; the light icon appears on right side
of LCD screen and the number of dots below it shows
which light intensity is on (one dot for LOW, two dots
for MEDIUM and three dots for HIGH).
To change the light intensity, press the push button
until the desired level is reached (from HIGH intensity,
pressing again will shut off the lights).
When lights are on (no matter the light intensity), press
and hold this push button until the light icon disappears
from the LCD screen; this will shut off the lights and
save the chosen light intensity.
The LED modules included with this hood are the
latest in LED cooktop illumination technology specially
designed to operate in the elevated temperatures of
cooking - off ering bright lighting and lasting up to 25
times as long as a standard bulb and greater reliability
than typical replacement LED bulbs.
MASTER ON/OFF
Press this push button to turn on the ligths and the
blowers at the last saved intensity. When either lights
or blowers are ON, pressing on this push button will
memorize the current blower speed and lighting level
prior to shut them OFF.
FILTER CLEANING REMINDER
This icon appears on LCD screen 30 seconds after
turning OFF the blowers when it is time to clean hood
and fi lters (refer to Cleaning and Maintenance on page
5). This happens every time the blowers are turned OFF
until the fi lter cleaning reminder has been reset. Once
the cleaning is done, reset the fi lter cleaning reminder by
pressing on blower activation push button for 3 seconds
while the icon appears on LCD screen for 30 seconds.