Installation Guide Instrucciones de Instalaci6n instructions dlnstallation English / Espafiol/Frangais 630.1390% 630.1 391 _ Models/Modelos/Mod_les: I
Dishwasher Safety ........................................................ Water Installation Requirements .............................................. Materials needed ..................................................................... supply requirements ....................................................... Electrical requirements ................................................................ Installation Instructions ................................................. Tools needed .........
Readtheseinstallatloninstructionscompletelyand them carefully. They will save you time and effort to ensure safety and optimum if the dishwasher dishwasher is installed This dishwasher follow performance. in a lacatlon is designed to be enclosed on the top and both sides by cabinetry. NEW INSTALLATION - If the dishwasher isa new installation, mast of the work must be done before the dishwasher is and help moved into place. that experiences Freezing temperatures (e.g.
Hammer Hole Saw Pliers Measure Needle Tape Mounting Wire Bracket Safety Nose Pliers Work Glasses Adjustable C_loves Screwdrivers Level Drill Strippers Wrench Screws Spring Clamp Screw Clamp Junction i: Toe Panel Screws Drain Hose o-Q Leg Leveler Screws 4 Box Screw
IMPORTANT! Before you begin, you must read the safety instructions! PRE-INSTALL [] Unpack CHECKLIST unit. installation Retain packing material until Make successful is complete. [] Remove all [] Inspect parts packing material to ensure from you have inside all the dishwasher. the necessary materials. [] Flush household hot water supply for at least two minutes.
Note: Plumbing installations Drain hose included is 92" will vary - refer to local codes. (234 cm) and can be extended to a maximum of 150" (381 cm). Ensure a portion of the drain hose is raised at least 20" (51 cm) above the floor. Ensure that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed 60 Hz, AC, connected grounded Note: Plumbing Always • • installations will vary - refer to local codes.
STEP | Enclosure Preparation NOTE: This dishwasher is designed and both sides by standard Select a location access to water Far proper supply dishwasher opening on the top kitchen cabinetry. as close to the sink as possible that the enclosure here. NOTE: If the cabinet to be enclosed residential far easy and drain lines. operation and appearance, is square and has the dimensions ensure shown is less than 24", the side strips may need to be removed.
Electrlcal Supply Ensure that the dishwasher electrical installation is in compliance with all national and local electrical codes and ordinances. The dishwasher is designed 60 Hz, AC, connected grounded electrical for an electrical circuit supply conductors AWG wire rated at 75°C Strip outer casing of electrical Dishwasher Volts 120 Hertz 60 rated for shall be a minimum #1 4 (1 67°F) or higher. wire to expose (65 - 76 mm) of the inner wires.
STEP 4 Removing the junction box cover While unit is still in position left, remove the iunction need it later. as shown in the figure to the box cover and set it aside. You will STEP 5 Removing the strain relief plate Once you remove the iunction box cover, remove the strain relief plate located directly behind the junction box cover. DO NOT DISCARD!. You will re-install this later.
STEP6 Attaching the hot water ilne NOTE: The 90 ° elbow fitting is not supplied dishwasher and must be purchased "Materials Needed" with the separately (see section). STEP 1 To prevent leaks, wrap tape firmly in a clockwise carefully the dishwasher direction for any breaks before elbow twice.
STEP 7 Attaching the mounting FOR WOODEN brackets UNDERCOUNTER NOTE: Before decide which method appropriate, for installing the mounting please the dishwasher is i.e side mount or top mount. Top mount is used countertops made be drilled easily. of marble, granite, drilled of securing brackets, of wood or other materials Side mount is used for countertops stone or other materials that can made that cannot be easily.
STEP9 Moving dishwasher into the cabinet iMPORTANT: Do not atlow teg teveters to scratch or mark floor. Ptace hands where pictured to push into pMace. As you slide the unit it, guide the water the sink, and electric excess drain line and drain line beneath hose toward the unit. Ensure that the hose is pushed through to the cabinet housing the sink. Units are typicatty positioned so that the door is flush with cabinet door and drawer fronts. For optimal noise reduction, with cabinet.
STEP 11 Electrlcal Connection Pass wires through strain relief inches of insulated plate. Tighten Bending clamp around the electricai of the strain relief wires, oriented Leave 3 to 4 the strain relief as shown. cable as shown will ease installation strain relief plate the screw. Make side of the strain relief you slide it into place. 13 through plate. Place the assembled box and re-attach and plate.
Note: Do not loosen or remove termlnal may occur. Bend the wires so the exposed the appropriate contacts. the left opening on the terminal (neutral) marked stripped wire shows above Securely tighten the terminal may occur.
STEP 12 Restoring the junction box cover Replace iunction box cover. Make sure the cover is seated behind the front lip of the strain relief cover with the screw (part plate. Attach F) from the installation the kit. STEP 13 NOTE: if the dishwasher Adjusting the leg levelers operate properly and could cause leaks. Check that the leveling legs are firmly against is nat leve!, it may nat the floor. • Place a level against • Check that the dishwasher needed, • adjust the front panel.
STEP]4 Attaching the mounting brackets Insert screws (part A) through brackets and attach recommended). pre-positioned unit to enclosure mounting (pre-drilling of holes STEP15 Drain Hose Connection Route drain hose to household Note: Plumbing Always 20"(51 cm) -Max. Length of Drain Hose included adding an extension length for proper 1 68" (426 cm) 16 to local codes. include a Loop in the Drain Hose for proper - Height of loop -[Min. When plumbing.
Attach drain hose (part (part C) and tighten. vent hose. D) to plumbing with screw clamp Do nat make any connections Do nat cut drain hose. Coil excess drain cabinet behind unit. NOTE: When connecting drain that disposal knack out plug is remaved. hase safely hose to disposal, to the air inside make sure STEP 16 Attaching water llne and checking for leaks Attach water line to incoming hat water • Turn an water and check far leaks. • Turn power • Start shut off valve. back on at fuse box.
STEP17 Installlng the toe panel Attach the metal toe panel with screws (Part E) so it is flush with the floor. Your installation is now complete. STEP 18 Check operation * Turn the fuse back on. Read the Use and Care Manual dishwasher. Start the dishwasher and allow that came with your it to complete the shortest wash cycle. Check that the dishwasher water is coming If not, please operate" If dishwasher is functioning properly and into the unit.
