Installation Guide Instrucciones de Instalaci6n instructions d'lnstallation English / EspaioJ / Frangais Models/Modelos/Mod_les: 630.1395 _ I
Dishwasher Safety ........................................................ Water Installation Requirements .............................................. Materials needed ..................................................................... supply requirements ....................................................... Electrical requirements ................................................................ Installation Instructions ................................................. Tools needed .........
Readtheseinstallatloninstructionscompletelyand them carefully. They will save you time and effort to ensure safety and optimum if the dishwasher dishwasher is installed follow • performance. in a lacatlon This dishwasher is designed to be enclosed on the top and both sides by cabinetry. NEW INSTALLATION - If the dishwasher isa new installation, mast of the work must be done before the dishwasher is and help moved into place. that experiences freezing temperatures (e.g.
Hammer Hole Saw Pliers Measure Needle Tape Mounting Wire Safety Nose Pliers Work Drill Strippers Glasses Gloves Adjustable Screwdrivers Level Bracket Screws Spring Clamp Screw Clamp ,'_,_ili_:':_i_ii_ _'_'_''i_J!_i,i_uii_iiiiiiiii Junction Box Screw Drain Hose Toe Panel Screws Wrench
IMPORTANT! Before you begin, you must read the safety instructions! PRE-INSTALL [] Unpack CHECKLIST unit. installation Retain packing material until Make successful is complete. [] Remove all [] Inspect parts packing material to ensure from inside you have all the dishwasher. the necessary materials. [] Flush household hot water supply for at least two minutes.
Note: Plumbing installations Drain hose included is 92" will vary - refer to local codes. (234 cm) and can be extended a maximum of 150" (381 cm). Ensure a portion of the drain hose is raised at least 20" (51 cm) above the floor. Ensure that the dishwasher electrical compliance with all national ordinances.
STEP | Enclosure Preparation NOTE: This dishwasher is designed and both sides by standard Select a location access to water For proper to be encMosed on the tap residential kitchen cabinetry. as close to the sink as possible supply dishwasher for easy and drain lines. operation and appearance, that the enctasure is square and has the dimensions here. +235/8" - 241/4 ensure shown .+(600 -61 6 mm) with side strips removed.
Electrlcal Supply Ensure that the dishwasher electrical compliance with all national ordinances. The dishwasher installation is in and local electrical is designed supply of 120V, 60 Hz, AC, connected dedicated, properly or breaker rated grounded 75°C (167°F) for an electrical to a dishwasher- electrical circuit with a fuse for 15 amps. Electrical shall be a minimum #14 AWG supply copper-only wire rated wire to expose (65 - 76 mm) of the inner wires.
STEP 4 Removing the junction box cover While unit is still in position as shown here, remove the iunction box cover and set it aside. You will need it later. STEP 5 Removing the strain relief plate Once you remove the iunction box, remove the strain relief plate located directly behind the iunction box cover. DO NOT DISCARDL You will re-install this later.
STEP6 Attaching the hot water llne NOTE: The 90 ° elbow fitting is nat suppUied with the dishwasher and must be purchased (see _Materials Needed" separately section). STEP 1 To prevent tape leaks, wrap the dishwasher firmly in a clockwise carefully suppty direction for any breaks before elbow with plumbing twice.
STEP 7 Attaching the mounting brackets Flip unit back upright, ensuring water line remains in appropriate channel and is not pinched. If your dishwasher has the pre-attached mounting you have a wooden undercounter, are positioned direction as far apart of arrows. NOTE: Before decide for by sliding them in to countertop installing the mounting brackets, yet. please of securing the dishwasher is i.e., side mount or top mount. Top mount is used countertops made be drilled easily.
STEP 8 Connecting drain hose to the dishwasher To attach the drain hose, orient it towards the sink. IMPORTANT: Route hose towards the direction of sink PRIOR to connection. attaching dishwasher. hose elbow DO NOT rotate This would the hose after cause it to crimp. Attach it to the the drain to the back of the unit with the included spring clamp. NOTE: DO NOT use any other damp! It couMd cause the hose to collapse.
STEP10 Attaching the strain relief Attach the strain relief plate. The two screws on the back of the strain relief be positioned assembly. strain relief (not included) ta the strain relief as shown to prevent Tighten the strain relief interferences shauMd during lock nut to prevent the from turning. STEP 11 Electrlcal Connection Pass wires through strain relief and pMate. Leave 3 to 4 inches of insulated wire extending plate.
Place the assembMed strain relief box and re-attach the screw. side of the strain relief plate plate Make back into the iuncfion sure the tab on the right is outside the iuncfion box as you slide it into place. Note: Do not loosen or remove terminal screws! Damage may occur.
Make sure that the exposed stripped (non-insulated) wire shows above SecureJy tighten or damage and below the terminal portion the terminal of each screw. screws, but do not over-tlghten may occur. STEP 12 Restoring the junction box cover Replace junction box cover. Make sure the cover is seated behind the front lip of the strain reJief plate. cover with the screw (part 15 Attach F) from the installation kit.
STEP 13 NOTE: if the dishwasher Adjusting the leg levelers is not level, it may not operate properly and could cause leaks. Check that the leveling legs are firmly against * Place a level against Check that the dishwasher levelers Open the floor. the front panel. until dishwasher is plumb. If needed, adiusfleg is plumb. the door. Place the level inside against the top of the tub. Check that dishwasher is level from side to side.
STEP 15 Drain Hose Connection Note: Plumbing installations will vary - refer to local codes. Drain hose included a maximum of 150" hose is raised Always is 92" (234 cm) and can be extended (381 cm). Ensure a portion at least 20" (51 cm) above 20"(51cm) Length of Drain Hose included When adding an extension If the dishwasher drain disposer, remove drain connection. the plug from hose (part (part C) and tighten. vent hose. function 92" is 168" / (233 cm) (426 cm).
STEP 16 Attaching water llne and checking for leaks Attach water line to incoming hot water • Turn an water and check far leaks. • Turn power • Start valve. back on at fuse box. washer, listen far water distribution. leaks. shut off Press Cancel/Reset and pump far water to drain and check far Check far leaks at the drain hose connection, the water connection under the sink as well as the water line connection under the dishwasher. / \ STEP 17 Installing the toe panel Attach the metal toe
STEP18 Check operation • Turn the fuse back on. • Read the Use and Care Manual dishwasher. • Start the dishwasher and allow that came with your it to complete the shortest wash cycle. • Check that the dishwasher water • is coming If nat, please operate" if dishwasher is functioning and refer to the "Dishwasher does nat section below. does not operate: Try one of the solutions suggested service call. * properly into the unit.