Installation guide

ManualsBrandsKenmore Elite ManualsCooktopOfficial Kenmore Elite gas cooktop

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

_r_ If the information in this manual is not followed exactly, a fire or explosion may result

causing property damage, personal injury or death.

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your building.

Immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

Gas Cooktop

Dimensions

21/2"

(6.4

Gas Cooktop (6.4 cm)

Cutout Dimensions ' _ ii

Figure 1

_i_i;!;i_i_i!_i_i_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_i_i_i!ii_i_iiiiiiiiiiiiiiiiii_i_ii_i!_ii_i!_i_i_ii_ii_ii_ii_i_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii_ii__iiiiiiii_iiiiiiiiii_ii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_!_i!_!_i_i_i_i_i_i_i_i_i_i_i_i_!i!_!_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_!_i_ii_i__!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!i_!ii_ii_ii_!_ii_i_!_!_i_!!!!i!!_i!ii_ii_i_ii_ii_ii_ii_ii_ii_ii_ii_ii_i_ii_ii_i_ii_iiiiiiiiiiiiiiiiiiiiiiiiii_i_i_i_i_!i_!_i_!_!i!!_!!i!i__}_i_i@_i@_!!!!!!!!!!!!!!_!!!i!i!!_!i!i!i!_ii_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_i_ii_ii_i__

30"GasCooktop 30 (76.2) 213A(55.2) 4¼ (10.8) 27(68.6) 19 (48.3)

36"GasCooktop 36(91.4) 2134(55.2) 4¼ (10.8) 33¼(84.5) 19(48.3)

i .................................i

30"GasCooktop 27¼(692) 28Y2(724) 191/8(486) 19_A(502) 8(20.3)

36"GasCooktop 33¼(84.5) 34¼(87) 19Y_(48.6) 19_A(50.2) 8(20.3)

All dimensions are stated in inches and (cm).

Dimension14includesa B" (12.7cm) spaceunderneath the cooktop for connection to gas supplyline.

NOTE: Wiring diagrams for this cooktop are enclosed in this booklet

Printed in United States

318201479 (0806) Rev.A

English - pages 1-9

EspaBol- p_iginas 10-18

Wiring Diagram 19-20

Summary of content (20 pages)

PAGE 1
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR'S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. _r_ If the information causing property damage, in this manual personal is not followed exactly, a fire or explosion may result injury or death. FOR YOUR SAFETY: -B ® ® ® ® Do not store or use gasoline or other flammable the vicinity of this or any other appliance.
PAGE 2
important Notes to the Installer 1. Read all instructions contained in these installation 2. 3. 4. 5. instructions before installing the cooktop. Remove all packing material before connecting the electrical supply to the cooktop. Observe all governing codes and ordinances. Be sure to leave these instructions with the consumer. Note: For operation over 2000 ft. elevation above sea level, reduce appliance rating by 4 percent, and by the same amount for each additional 1000 ft.
PAGE 3
13" (33cm) Max.Depth ForCabinet Installed Above Cooktop. t" 18" Min. (45.7 cm) 11/2" (3.8 cm)Minimum Distance Between Rear Edge of Cutout and Nearest Combustible Surface Above Countertop. --It Clearance 30" (76.2 cm) Min. Clearance Between the Top of the Cooking Platform and Unprotected Wood or Metal Cabinet C Drawers Cannot Be Used with This _To prevent fire, or burns when reaching over heated surfaces, cabinet storage space located above the cooktop should be avoided.
PAGE 4
Typical Gas Cooktop Installation Over an Electric Built-in Oven Installed Under the Counter A__ I_l----- 18" (45.7 cm) Max.-----_ ÷ 4" (10.2 cm) Manifold Pi 61/2" 5" .(16.5 cm) Flare (12.7 cm) Min.
PAGE 5
Typical Under Counter Installation of an Electric Built-in Oven with a Cooktop Mounted Above Junction box must Side filler panels are necessary to isolate the unit from adjoining cabinets. Panel height should allow for installation of approved cooktop models. See "Typical Gas Cooktop Installation Over an Electric Built-in Oven Installed Under the Counter" This cooktop may be installed over certain built-in electric oven models. on previous page. be located approx.
PAGE 6
Wall Outlet Location : Provide an Adequate Gas Supply This cooktop is designed to operate on natural gas at 4" of manifold pressure only. 12"q A pressure regulator is connected in series with the manifold on the cooktop and must remain in series with the supply line. For proper operation, the maximum inlet pressure to the regulator must be no more than 14" of water column (W.C.) pressure. 10" ' For checking the regulator, the inlet pressure must be at least 1 " (or 2.
PAGE 7
Assemble theflexibleconnectorfromthe gassupply pipeto the pressure regulatorin thefollowingorder: 1. manualshutoffvalve 2. 1/2"(1.3cm)nipple 3. 1/2"(1.3cm)flareunionadapter 4. flexibleconnector 5. 1/2"(1.3cm)flareunionadapter 6. 1/2"(1.3cm)nipple 7. pressure regulator Usepipe-jointcompoundmadefor usewith Naturaland LP/Propane gasto sealallgasconnections. If flexible connectors areused,becertainconnectors arenot kinked. Thesupplylinemustbeequippedwith anapproved manualshutoffvalve.
PAGE 8
Check Operation Referto the UseandCareGuidepackaged withthe cooktopfor operatinginstructions andfor careand cleaningof yourcooktop. Donottouchtheburnersuntilyouarecertainthatthe cooktophascompletely cooled.Theymaybehot enoughto causeburns. IA, Install BurnerCaps=RegularBurners Thiscooktopisequippedwith sealedburnersasshown (seeFigure8). A. Unpackyourburnerheadsandburnercaps. B. Placeburnerheadovereachgasorifice,matching the headwith the orificesize.
PAGE 9
4.Adjustthe "low" settingfor regularsurface burnervalves(Figure10) a. Pushin andturn controlto LITEuntilburnerignites. b. Quicklyturnknobto LOWEST POSITION. c. If burnergoesout, resetcontrolto OFF. d. Remove the surfaceburnercontrolknob. e. Inserta thin-bladedscrewdriver intothe hollowvalve stemandengagetheslottedscrewinside.Flamesize canbeincreased or decreased with theturn of the screw.Turncounterclockwise to increase flamesize. Turnclockwiseto decrease flamesize.
PAGE 10
LA INSTALACION Y EL SERVICIO DEBEN SER REALIZADOS POR UN INSTALADOR CAUFICADO. IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL iNSPECTOR ELI_=CTRICOLOCAL. LEA Y GUARDE ESTAS INSTRUCCIONES PARA FUTURAS REFERENCIAS ocurrir incendios Si todas las instrucdones de este manual no son observadas a la letra, se puede o explosiones que pueden causar daEos materiales, lesiones o la muerte.
PAGE 11
Notas Asegurese que la plancha de cocinar sea instalada y puesta a tierra correctamente por un instalador o t_cnico calificado. importantes para el instalador: 1. Lea todas las instrucciones de instalaciOn antes de realizar la instalaci6n de la plancha de cocinar. 2. Retire todos los articulos de embalaje antes de realizar las conexiones el_ctricas a la plancha de cocinar. 3. Observe todos los c6digos o reglamentos estatales 4. Aseg0rese que el consumidor tenga estas instrucciones. 5.
PAGE 12
M_ix.profundidad degabinetes instalados por encimadela plancha de empotares13" (33cm). T 11/2"(3.8cm)MinimoDistancia entreelhordeposteriordel huecoy lamascercasuperficie combustible porencimadel mostrador. IX 24" C61cm_ __plataforma I _ I _ ' _ Espacio 30" (76.2cm) Minimode espacio entre la parte superiodela de la plancha de cocinaryel fondodeuna maderanon protegidao armario met_qlico. B _ ible utilisar cajones con ' esta........
PAGE 13
Instalacion tipica de la plancha de cocinar a gas por encima de un homo electrico empotrado instalado debajo del mostrador 18" (45.7 cm) M_ix.-----_ I II I ÷ 4" (10.2cm) 61/2" Tubo m01ti 5" (13.5 cm) (12.7 cm) Min.
PAGE 14
Tipica instalaci6n de un horno el ctrico empotrado plancha de cocinar por encima Todas las fijaciones de montaje deben de estar utilizadas para sujetar el homo empotrado a los armarios. Refiere alas instrucciones de instalaci6n del homo empotrado. con una Entrepaflos Ilenador de lados son necesarios para aislar el aparato de los armarios adyacentes. La altura de panel debe de permitir la instalaci6n de modelos de planchas de cocinar aprobantes.
PAGE 15
Ubicacion de ia toma de corriente 1 2 II NOTA; Si no existe una toma de corriente, contacte a un eWectricista caWificado para realizar la instalaci6n, _- 8"¸¸/" _j. Area recomendada corriente a tierra Para que manejo correcto, la presi0n de entrada m_ixima hacia el regulador no debe exceder 14" de presi0n de la columna de agua. de ia pared Para controlar el regulador, la presi6n de entrada debe ser de al menos 1" (o 2.5 Kpa) mayor que el ajuste de la presi6n del mOltiple del regulador.
PAGE 16
Monteel conector flexibledeltubodelsuministro degas alregulador depresiOn enfuncionamiento: 1. v_lvuladecierremanual 2. boquillade1/2"(1.3cm) 3. adaptorde1/2"(1.3cm) 4. conectorflexible 5. adaptatorde1/2"(1.3cm) 6. boquillade1/2"(1.3cm) 7. regulador depresiOn. Utiliceuncompuesto detuboarticulado parausodegas naturaly propanoparasellartodaslasconexiones degas. Siseutilizanconectores flexibles, aseg0rese quelos conectores noest_in torcidos.
PAGE 17
Verifique ia 4. Para instalar la cabeza del Quemador, las Tapas y el Borde exterior, referir a la figura 9 y seguir los siguientes pasos: Paso 1: Alinear la clavija A que sobresale de la Cabeza del Quemador con el hoyo de la Base del Quemador. Paso 2: Colocar el Borde exterior del Quemador alrededor de la Base y la Cabeza. Paso 3: Alinear el hoyo de la Tapa Externa del Quemador con la clavija B de la Cabeza del Quemador. Paso 4: Colocar la Tapa Interna del Quemado centrada sobre la Base del Quemador. 5.
PAGE 18
4.Ajustebajo("LO")arala v,ilvula de los quemadoresde superficie(Figura9) a.Presione y gireelcontrolhastala posiciOn LITEpara prenderlosquemadores. b.Girer_pidamentegirelaperilla a laPOSICION MAS BAJA. c.Sielquemador seapaga,reajuste el controlaOFE d. Retirelaperilladelquemador desuperficie. e.Inserteundestornillador fino-aplanado enelorificodel wistagodelawilvulae inserteeneltornilloranurado. Eltamahodelallamapuedeaumentarse o disminuirse d_indole vueltaal tornillo.
PAGE 19
TOP BURNER IGNITER OPTIONAL GUEMADOR DE ENCENDIDO CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WIRING ERROR CAN CAUSE IMPROPER AND L1 SUPERIOR OPCIONAL BOOGIE VERIFY D'ALLUMAGE-BRULEUR PROPER OPERATION AFTER WHEN SERVICING DANGEROUS OPERATION. CONTROLS, N SERVICING, AVlSO: ETIQUETE REALIZAR TOP BURNER IGNITER ALAMBRAJE PUEDE Y PELIGROSO.
PAGE 20
TOP BURNER IGNITER QUEMADOR DE ENCENDIDO SUPERIOR BOUG I E D' ALLUMAGE BRULEUR CAUTION: ALL WIRES PRIOR ERROR CAN CAUSE LABEL WIRING VERIFY PROPER TO DISCONNECTION IMPROPER AND OPERATION AFTER WHEN DANGEROUS SERVICING OPERATION CONTROLS. SERVICING. AVlSO: RIGHT REAR IGN. SW. INT. ENC. TRASERO DERECHO INTER. ALLUH. D. AR. TOP BURNER IGNITER OUEMADOR DE ENCENDIDO SUPERIOR BOUGIE D'ALLUMAGE BRULEUR ETIOUETE TOOOS REALIZAR ET ALAMBRAJE v PELIGROSO.