® ELECTRIC COOKTOP f PARRILLA COCINAR LECTRICA Models, Modelos: 790.4281_, 790.4282_ .,.-'---Color number, nL_mero de color www.sears.com Sears Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. P/N 318200648 Rev.
Table of Contents Operating the Bridge Surface Element .......................... 12 Warm & Hold Feature .................................................... 12 Sabbath Feature Mode .................................................. 13 Locking the Controls ..................................................... 13 MinuteTimer ................................................................. 13 General Care & Cleaning ............................................. 14-15 Cleaning Various Parts of Your Cooktop .
important Safety instructions Read all instructions before using this appliance. Save these instructions for future reference. This manual contains importantsafety symbols and instructions. Please pay attention to these symbols and follow all instructions given.
important Safety instructions expose a portion of the surface heating unit to direct contact and may result in ignition of clothing. Proper relationship of utensil to the surface unit will also improve efficiency. • Utensil Handles Should Be Turned inward from Edges of Cooktop and Should Not Extend Over Adjacent Surface Units. To reduce the risk of burns, ignition of flammable materials, and spillage due to unintentional contact with the utensil. • Never Leave Surface Units Unattended ata Hit Heat Settings.
Cooktop Features READTHESE iNSTRUCTiONS CAREFULLY BEFORE USING THE COOKTOP The Cooking Zones may appear to be cool while turned ON and after they have been turned OFF. The glass surface may be HOT form residual heat transferred from the cookware and burns may occur. 1. 2. 3. 4. 5. Left Rear Single Radiant Element Left Front Bridge Radiant Element Right Rear Single Radiant Element Right Front Double radiant Element Center Rear Single Radiant Element (Fig. 2 only) 6. Right Rear Element Control Pads 7.
CORRECT Surface Cooking Use Proper W Cookware Cookware should have flat bottoms that make good contact with the entire surface heating element. Check for flatness by rotating a ruler across the bottom of the cookware (See Figure 1 ). Be sure to follow the recommendations for using cookware as shown to the right. iNCORRECT /,_ t Flat bottom and straight sides. ÷1 I_ • Tight fitting lids. Weight of handle does not tilt pan. Pan is well balanced.
Setting Surface Controls General Cooktop information About the Ceramic Glass Cooktop The ceramic cooktop has radiant surface elements located below the surface of the glass. The design of the ceramic cooktop outlines the area of the surface element underneath. Make sure the diameter of the pan matches the diameter of the element outline on the cooktop. Heat is transferred up through the surface of the cooktop to the cookware. Only fiat-bottom cookware should be used.
Setting Using Surface Controls the Touch (cont'd) Control The recommended way to use the touch pads on the cooktop is shown JnFigure t. Be sure that your finger is placed in the center of the touch pad as shown. If the finger is not placed on the center of a pad, the cooktop may not respond to the selection made. Lightly contact the pad with the flat part of your entire fingertip. Do not just use the narrow end of your fingertip.
Setting Surface Controls The Electronic Surface Element (cont'd) Control (ESEC) The Electronic Surface Element Control (ESEC) feature provides a digital display of the radiant surface elements on the cooktop. The ESEC display in combination with the touch pads is designed to replace conventional control knobs.
Setting Surface Controls (cont'd) Operating Single Elements Radiant Surface The 30" cooktop has 2 SINGLE radiant surface elements: the RIGHT REAR and the LEFT REAR positions (Figure 1); The 36" cooktop has 3 SINGLE radiant surface elements: the RIGHT REAR, the CENTER REAR and the LEFT REAR positions (Figure 2). To Operate the Single Radiant Surface Elements: 1. Place correctly sized cookware on the radiant surface element. 2. Touch and hold the P_W_ key pad until a beep sounds.
Setting Surface Controls (cont'd) Operating the DUAL Surface Element The cooktops are equipped with a DUAL radiant surface element located at the right front cooktop position (Figures t & 2). indicator lights on the control panel at that position are used to indicate what portions of the dual radiant element will heat. The INNER light indicates that only the inner element will heat. The OUTER light indicates that both inner and outer elements will heat together.
Setting Surface Controls Operating the Bridge Surface (cont'd) Element The cooktop is equipped with a"BRI DGE" surface eJement locatedat the leftcooktop position (See Figures I & 2). Indicatorlights on the cooktop are used to indicatewhat portions of the Bridge eJementwill heat. The Bridge element begins with the leftFRONT position only (Figures 3 & 4) and Figure 1 when selected with the +BRIDGE element (Figures 5 & 6) it will provide a combination of 2 heating surfaces.
Setting Surface Controls Sabbath Feature (cont'd) Mode When the Sabbath feature is ON, all electronic surface element control displays show "Sb" (Fig. t). The surface elements can be used even if the Sabbath Feature is on. To activate the Sabbath Feature Mode: _ in order to enter Sabbath at least one radiant burner has to be active. The user has to activate the Fig. t Timer (timer up slew) pad and the _ (lock) pad at the same time for a few seconds. Timer and element displays will show "Sb'.
General Care & Cleaning Cleaning Various Parts of Your Cooktop Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANINGS NOW WILL REDUCE THE DIFFICULTY AND EXTENT OF A MAJOR CLEANING LATER. Surfaces How Aluminum (Trim Pieces) Use hot, soapy water and a cloth or paper towel. Dry with a clean cloth.
General Care & Cleaning Cleaning Recommendations for the Ceramic Glass Cooktop Before cleaning the cooktop, be sure the controls are turned to OFF and the cooktop is COOL. DO NOT use a cooktop cleaner on a hot cooktop. The fumes can be hazardous to your health, and can chemically damage the ceramic glass surface. For light to moderate soil: Apply a few drops of CookTop® Cleaning Creme directly to the cooktop.
Before You Call POSSIBLE CAUSE/SOLUTION OCCURRENCE Entire cooktop operate. does not House fuse has blown or circuit breaker has tripped. Check/reset breaker or replace fuse. If the problem is a circuit overload, have this situation corrected by a qualified electrician. Wiring connection is not complete. Call 1-800-4-MY-HOME® for service (see back cover). Power outage. Check house lights to be sure. Call your local electric company for service. Surface element does not heat. No power to the appliance.
Master Protection Agreements Acuerdos Congratulations on making a smart purchase. Your new Kenmore ® product is designed and manufactured for years dependable operation. preventive having and But like all products, maintenance a Master or repair Protection from Agreement it may require time to time. That's can save of when you money aggravation. beyond no functional the failure product warranty.
Your Home For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters. 1-800-4-MY-HOME Call anytime, ® day or night (U.S.A. and Canada) www.sears.com For expert home (1-800-469-4663) solutions www.