Table of Contents Setting Downdraft Vent System Warranty 2 Operating the Single Rodin Surface Elements... IMPORTANT SAFETY INSTRUCTIONS . 4 Operating the Dual Radiant Surface Element. .Q Serial Plate Location. 4 Operating the Bridge Radiant Surface Element Product Re card 4 Operating the Triple Radiant Surface Element. Cook top Features, 5 General Care & Cleaning. Setting Surface Control 1 Cleaning Your Cook top. 12 About the Ceramic Glass Cook top. 4 Ceramic Glass Cook top Cleaning & Maintenance...
IMPORTANT SAFETY INSTRUCTIONS Read all instructions before using this appliance. Soave these instructions for future reference. This manual contains important safety symbols and instructions. Please pay attention fo these symbols and follow all instructions given. PLAGIARIZE This symbol will help alert you to situations that may cause serious bodily harm, death or property dosage: yp instillation This symbol will help alert you to situations that may cause bodily injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS in the downdraft vent system could catch fire, When flaming foods under the hood, turn the fan on. FUSE Use Proper Pan Size. This appliance is equipped with one or more surface units of different sizes. Select utensils having flat bottoms large enough to cover the surface unit. The use of undersized utensils will expose o portion of the surface heating unit to direct contact and may result in ignition of clothing.
Leopoldo Features READ THESE INSTRUCTIONS CAREFULLY BEFORE USING THE COOK TOP Pas] The Cooking Zones may appear fo be cool while turned OM and after they have been turned OFF. The glass surface may be HOT from residual heat transferred from the cookware and burns may occur Downdraft Vent System Right Rear Dual with Grate Cover Radiant Element Right Rear . Dual Element +7 Control Knob Left Rear Single w..
Setting Surface Controls About the Ceramic Glass Cookie The ceramic cook top has radiant surface elements located below the surface of the glass. The design of the ceramic cook top outlines the area of the surface element underneath. Make sure the diameter of the pan matches the diameter of the element outline on the cook top. Heat is transferred up through the surface of the cook top ta the cookware. Only flat-bottom cookware should be used.
Setting Surface Controls General Leopoldo Information Use the table below to determine the correct setting for the kind of food you are preparing. The low settings are used to simmer and keep larger quantities of foods warm such as stews and soups. The lowest simmer settings ore ideal for delicate goads and melting chocolate or butter. Note: The size and type of cookware used will influence the setting needed for best cooking results.
Setting Surface Controls Operating the Single Radiant Surface Elements The cook top has 2 single radiant surface elements: the RIGHT FRONT & LEFT REAR {for 30" model) or LEFT FRONT & RIGHT REAR {for 36" model} positions (Figures 1 and 2. To Operate the Single Radiant Surface Elements 1. Place correctly sized cookware on the radiant surface element, 2. Push in and turn the surface control knob in either direction to the desired setting (Figure 31. Turn the knob to adjust the setting if desired.
Setting Surface Controls Operating the Dual Surface Radiant Element The cook top is equipped with a dual radiant surface element located at the RIGHT REAR (for 30” model} or at the LEFT REAR (for 36” medal) position {Ses Figures 1 & 2). Symbols on the control knob area are used to indicate which coil of the dual radiant element will heat. The © indicates that only the inner coil will heat (Figure 3). The @ indicates that both inner and outer coll will heat (Figure 4).
Setting Surface Controls Operating the Bridge Surface Radiant Element The 30” cook top is equipped with a "BRIDGE" surface element located of the left front and middle (See Figure 1} positions. The Bridge can be used when cooking with rectangular (like a griddle) or oval shaped cookware. The element will maintain an Sven temperature setting across both portions of the Bridge. If needed for normal cookwares, the Bridge element can work like a single element without the Bridge (See Figure 4).
Setting Surface Controls Operating the Triple Surface Radiant Element The 36" zoology is equipped with a triple radiant surface element located of the right front position (See Figure 1). Symbols an the contra knob area are used to indicate which coil of the dual radiant element will heat. “Single o", "Dual" and “Triple on the control knob are used to indicate which portion of the triple element will heat. “Single” indicates that only the inner coil will heat (Figure 2).
General Care & Cleaning Cleaning Your Cook lop Before cleaning any part of the colophon, be sure all controls are fumed OFF and the cook top is COOL, REMOVE SPILLOVERS AND HEAVY SOILING AS SOON AS POSSIBLE, REGULAR CLEANINGS NOW WILL REDUCE THE DIFFICULTY AND EXTENT OF A MAJOR CLEANING LATER. Surfaces How to Clean : Painted and Plastic For general cleaning, use hot soapy water and a cloth.
General Care & Cleaning Cleaning Recommendations for the Ceramic Glass Leopoldo FAN bot ore craning the coolie, be sure the confreres are tuned to OFF and the coolie Is COCK INTENTNESS DO HOT bse & codon cleaner ond hot costumier the fumes com be overdoses bo your hellion, ond cen shambolic marmot the ceramic alas subs Far light to moderate soil: Apply a few drops of CookTop® Cleaning Creme directly to the cook top.
General Care & Cleaning Cleaning the Downdraft Vent System Be sure to turn off the downdraft vent system before cleaning any of its parts. FECES To avoid possible bums use care when cleaning the downdraft system, DO NOT attempt to clean the cook top whenever the glass top or the vent grate are still hot. Cleaning the vent grate Remove the vent grate (Fig. 1} from the blacktop by lifting it off. The vent grate is dishwasher safe and may be cleaned in the dishwasher.
Before You Cali OCCURRENCE POSSIBLE CAUSE/SOLUTION Entire cookie does not aerate, Hausa fuse has blown or circuit bracket has tripped. Check /reset breaker or replace fuse, If the problem is circuit overload, have this situation corrected by a qualified electrician. Wiring connection is not complete. Call for service (see back cover). Power outage. Check house lights to be sure. Call your local electric company for service. Surface element does not heat. Mo power to the appliance.
Your Home For troubleshooting, product manuals and expert advice: @ manageability www.managemylife.com For repair — in your home — of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.
