Before Using Your New Canister Cave Vacuum Cleaner . Removing Clogs Packing List . . . Cleaning Exterior Kenmore Vacuum Bag Changing Important Safety Instructions . Motor Safety Filter Changing Ports aud Features |, Exhaust Filter Changing Assembly Instructions PowerMate® Care Operating Instructions Belt Changing and Agitator How to Start Cloning .. Vacuuming Tips Bulb Changing Suggested Pile Leigh Agitator Servicing 26 Attachments . Attachment Use Table Troubleshooting 27-28 Attachment Storage .
Kenmore Vacuum Cleaner Limited Warranty General: All models of Kenmore Vacuum Cleaners, with the exception of central vacuum systems, which shall be subject to different warranty provisions, sre warranted to be free From defects in materials or workmanship for a specific time per lad as stout below {the "Warranty Period"). Warranties extend to the original purchaser of o Kenmore Vacuum Cleaner only and are non-transferable. Purchases made through an online auction or through any website other than www.
ih PIC EVENT SHALL SEARS BE LIABLE FOR AMY INCIDENTAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES, WHETHER RESULTING FROM THE USE, MISUSE OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT. THE EXCLUSIONS IN THIS PARAGRAPH SHALL NOT APPLY IN JURISDICTIONS WHERE APPLICABLE LAW DOES MOT ALLOW FOR THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. IM SUCH JURISDICTIONS, THIS PARAGRAPH SHALL NOT APPLY, BUT THE REMAINING PROVISIONS OF THIS DOCUMENT SHALL REMAIN VALID.
IMPORTANT SAFETY INSTRUCTIONS AH WARNING: precautions including the following: Use your vacuum cleaner only as described in this wide, Use only with Sears recommended attachments, Disconnect electrical supply before servicing or cleaning out the brush area. Failure to do so could result in the electrical shack or brush suddenly starting. Do not leave vacuum cleaner when plugged in. Unplug from outlet when not in use and before performing servicing.
It is important to know your vacuum cleaner’s parts and features to ensure its proper and safe use. Review these before using your vacuum clearer.
HANDLE & HOSE ASSEMBLY 3-Way Johnson Switch Electronic Off Floor /Carpet Suction Control _ Tool Combination Brush CANISTER | Pot Power Mate Cord Rewind Button Pet Power Mate Storage Cover {Pet Formatted inside) — Pot . Tool Floor Exhaust Filter Cover | Brush Tool Stu rage Cover {Exhaust Fitter inside) {attachment storage inside).
Please pay special attention to these hazard alert boxes, and follow any instruct fins given. WARNING statements alert you to such dangers as fire, el burns and personal injury. CAUTION statements alert you to such dangers as per: sonar injury and/or property dosage. electric shock, &b warning Electrical Shock Hazard BO NOT plug into electrical supply unk assembly is complete, Failure fo do so could result in electrical shock or injury. Before assembling vacuum cleaner, check the PACKING LIST [page 2).
WANDS 1. Insert upper wand inch lower ward unit lock button snaps in place. To remove: Press wand lock button and pull wands apart. 2. Insert the plug of the Power Mute cord into the plug holder as shown, DO NOT Force. Raised earn of the plug must be towards hind, 3. Secure the cord into the cord holder on the buck of the wand. HANDLE Insert wand into handle until lock Burton snaps in place. Be sure has is not twisted. To remove: Press wind release button and pull up on handle.
4h caution Moving parts! To reduce the risk of personal injury, DO NOT touch the agitator when vacuum cleaner is on. Contacting the agitator while it is rotating can cut, bruise or cause other injuries. Always turn off and unplug farm electrical outlet before servicing. Use caution when operating near children. HOW TO START 2. Plug the polarized power cord info a a WARNING 120 Volt outlet located near the floor. Personal Injury and Product Damage} | To rewind: Turn off and plug the vacuum cleaner.
5. Select a position on the handle three way On/Off switch, CARPET turns on both the canister and the Power Mate motors, Headlight and agitator will come on. FLOOR turns on the canister motor only. OFF Turns vacuum cleaner off. NOTE « When this switch is in the FLOOR position the nozzle headlight DOES NOT function since no electricity flows to the Power Mate. ELECTRONIC SUCTION CONTROL The electronic suction control allows you to change the power of the vacuum cleaner suction motor.
VACUUMING TIPS SUGGESTED SWEEPING PATTERN For best cleaning action, the Power Mate should be pushed straight away from you ond pulled straight back. At the end of cache pull stroke, the direction of the Permeate should be changed fo point info the next section fo be cleaned. This pattern should be continued across the carpet or Floor with slow, gliding motions. SN NOTE: Fast, random strokes do not provide complete cleaning. STAIRS warning Personal Injury Hazard Use care if canister is placed on stairs.
EDGE CLEANER HOSE SWIVEL Active brush edge . A cleaners are on both The 360° hose swivel sides of the allows the hose to turn without moving the % canister, This is helpful for cleaning in small Power Mate. Guide either side of the Power Mate along the wall or next to areas. Check hose for furniture to help twisting before pulling remove dirt trapped canister, at carpet edges. SUGGESTED PILE HEIGHT SETTINGS For best deep down cleaning, use the XLO Hi — Shag, deep pile, or scatter rugs. setting.
ATTACHMENTS A caution BO NOT attach or remove handle or wands while vacuum cleaner is ON, This could course sparking and damage fhe electrical contacts or electronic controls. ATTACHMENTS ON HANDLE NOTE: If the Powerboat Is attached, turn vacuum cleaner off before 4. removing handle tr Wand from wand, = Referee 1 Press wand release button and pull up on Ronda. 2. Slide attachments firmly on handle os needed, See ATTACHMENT USE TABLE {page 16). Handle + je Combination Brush Handle, “15.
ATTACHMENTS ON WAND 1. To remove ward from Power Mate, lock ward in straighten-up position. 2. Press wand quick release pedal with foot and pull the wand straight up and out of Power Mate. 3, Put attachments on wand os needed. See ATTACHMENT USE TABLE [pose 17). Pet Powerful 3 NOTE: To remove combination brush, press the tool release button and slide off. Brush Release NOTE: To remove floor brush and/or Pet Power Mate, press the tool release button and slide off. Tool Release Tool Release. “16.
COMBINATION BRUSH The combination brush uses two tools, the dusting brush and the pet tool. Each is for use an various surfaces. See ATTACHMENT USE TABLE (page 17). To remove dusting brush or pet tool, release by pressing tab and Feting off the holder. To attach, insert CREVICE TOOL Attach the crevice tool to the handle storage locations as shown. LE Tab tab on holder N into sot on Slot, dusting brush or NS pet tool and NN press until tab snaps into place.
ATTACHMENT STORAGE Pet Power Mate This canister is equipped with an on-board storage area for a Pet Power Mate attachment, To Store: 1. Open the Pet Power Mate storage cover. 2. Insert the Pet Power Mate and press down until it clicks into place. 3. Close the lid securely. Storage Pel Power Mate To Remove: 1. Open the storage cover. 2. Remove Pet Power Mate from the storage area, 3. Use as needed. See ATTACHMENTS (page 15-17) and ATTACHMENT USE TABLE {page 17).
PERFORMANCE FEATURES Ah visioning Personal Injury Hazard Always tum off and unplug the vacuum cleaner before cleaning the agitator area as agitator may suddenly restart. Failure to do so can result in personal injury. BELT RESET The Power Mate has ser RESET built-in protection Hutton— against motor and Ny belt damage should the agitate jam, If the agitator slows down or stops, the BELT RESET shuts off the Power Mate. The canister motor will continue to run.
REMOVING CLOGS The vacuum cleaner creates suction that picks up dirt. Rapidly moving air carries the dirt to the dust bag through the airflow passages. The dust bag Jets the air pass through, while it traps the dirt For best cleaning results, keep the airflow passage open. Check the starred areas occasionally for clogs. Turn off ard unplug vacuum cleaner From outlet before checking. Gl TO CHECK FOR CLOGS: + Check dust bug and change if full. See BAG CHANGING (pose 21).
BAG CHANGING For best cleaning results, the dust bag should be changed often. The CHECK BAG indicator will come on when the bag needs to be changed or the airflow is blocked. NOTE: Use replacement dust bag bo. 20-5040, see port number detail in REPLACEMENT PARTS (page 7). REMOVING DUST BAG 1. Turn off and unplug vacuum cleaner. 2. Remove hose from canister. {See ASSEMBLY INSTRUCTIONS, page 9). 3. Pull hood release out and up. Hood Forefoot — ry 4, Lift canister hood. 3.
MOTOR SAFETY FILTER CHANGING The motor safety filter must be replaced when dirty. It should be replaced regularly depending on use conditions. The filter CANNOT be washed as it will lose its dust trapping ability, MOTE: Use replacement motor safety filter No. 2040321, see part number detail in REPLACEMENT PARTS (pose 7). 3. Replace the filter, white side facing 4 toward dust bag, by sliding if back info WARNING place ponder the ribs in the bug cavity.
EXHAUST FILTER CHANGING The exhaust filter cartridge must be replaced regularly. Replace the filter when the entire surface ren is covered evenly. The filter CANNOT be washed us # will lose its dust trapping ability. MOTE: Use replacement exhaust filter No, 20-40324, see part number detail In REPLACEMENT PARTS (page 7). Ab warning installed.
A warning Electrical Shock Or Personal Injury Howard Always turn off and unplug vacuum cleaner before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shack or personal injury from vacuum cleaner suddenly starting. BELT CHANGING AND AGITATOR CLEANING TO REMOVE BELT 1. Torn off and unplug vacuum cleaner. 5. Ta remove cover, grasp the sides and 2. Turn Power Mate upside down, pull out. 3. Unscrew the two {2} Power Mate cover resews, { SI &.
TO CLEAN AGITATOR: NOTE: in order fo keep cleaning efficiency high and to prevent damage fo your vac. wum cleaner, the agitator nest be cleaned every time the elf is changed, The agitator must alas be cleaned ac Cording to the following schedule: Locum Cleaner Use Clean Agitator HEAVY every week (used daily) MODERATE « every month (used 2-3 times / week) LIGHT every 2 months (used 1 time week) IMPORTANT Disconnect vacuum cleaner from electrical outlet.
LIGHT BULB CHANGING &h warning Electrical Shock Or Personal Injury Hazard Turn off and unplug vacuum cleaner before performing maintenance to the vacuum cleaner. Failure to do so could result in electrical shock or personal injury from the vacuum cleaner suddenly starting, &h caution Do not plug in or tur on until the vacuum cleaner is completely reassembled. 1. Remove PowerMaie® cover as shown in BELT CHANGING AND AGITATOR CLEANING action, 2.
Review this table to find do-it-yourself solutions for minor performance problems. Any other service needed should be performed by a Sears or other qualified service agent, AH WARNING Always turn off and unplug vacuum deanery before performing maintenance io the vacuum cleaner. Failure fo do so could result in electrical shock or personal injury. 1]} mo POSSESSIVENESS Vacuum cleaner wet 1. Unplugged at wall outer. 1. Lag in firmly, push ON/OFF switch dart, Hon. 2. Tipped circuit breaker blown 2.
CHECK BAG Indicator activates. JN > Ful or clogged dust bag, . Deity filters. . Blocked airflow passage. , Tartan attachment tools, © wm » Change bos, (loge 213 Change filers. {mage 22, 281 . Clew blockage from airflow passage. {page 20) . This is normal, Light should go off when too! i removed. Vaewurm loaner picks up movable rugs -orchestrate pushes too hard, oo . Wrong nie height setting, . Suction fon strong 2 e . Adjust setting. . Select lows Power Level Cord won'i rewind. 1. Dirty power cord. 1.
Avant de vous servir de voie nouvel aspirateur . . Liste d'emballage . Garantie de Aspirateur Ken more .. Mesures de Sécurité Importantes Piccolos et Caractéristiques Assemblage . . . Instructions d' Opérations Pour commenter Conseils de nettoyage & TaSpIrteur oogone. 1213 Réglages suggérés de hauteur de mols « Accessoires Table d'utilisation accessoires flageolement des accessoires . .
Garantie limitée des aspirateurs Ken more ; Tous les modelés d'aspirateur Ken mare, & l'exception des systèmes d’aspiration centrale qui font l’objet de dispositions de garantie différentes, sont garantis contre tout défaut de matériau ou de fabrication pendant une période de temps précise, telle qu'établie ci-dessous (ia * période de garantie Cette garantie ast offerte uniquement & acheteur initial de Aspirateur Ken more ef rets pas transférable.
SERAS NE PEUT EN AUCUN CAS ÊTRE TENUE RESPONSABLE DE TOUT DOMMAGE ACCESSOIRE, SPÉCIAL, INDIRECT OU consécutif, QUI résulterait DE L’UTILISATION, DE L’UTILISATION IMAPPROPRIEE, DE incapacitante D'UTILISER LE PRODUIT OU DES DÉFAUTS DU PRODUIT.
MESURES DE SÉCURITÉ IMPORTANTES Lire foudes les instructions contenues dans ce manuel avant de monter ou viriliser voire aspirateur AADVERTENCIA: Votre sécurité nous est trais important, Afin de réduire le ris électriques, de lésions corporelles ou de dommages lors de | ue d’incendie, de chocs ‘inutilisation de I'aspirateur, prendre des masures de sécurité de base, y compris les suivantes ¢ Utiliser Aspirateur uniquement de lo maniéré décrite dons ce manuel.
ou de dégâts. $l vous plaît notez ef suivez particulièrement les instructions contenues dans ces carrés. Les instructions contenues dans los carrés intitulés AVERTISSEMENTS vous reviennent de certains danger comme, par exemple, de feu, de chocs électriques, roulures ef autres blessures.
TUBES 1. Miserere le tube supérieur dans le tube inférieur jusqu’où déclic du bouton de verrouillage. Pour raturer © Appuyer sur le bouton de verrouillage du buse ot frire Parton / en ra fief Joe Tbe supérieur Bouton de vitriolage Porta. cordon oe Tis inférieur 2. Brancher la fiche et le cordon du PowerMate de la maniéré illustrée, NE PAS forcer. La portion en relief de la fiche doit être tournée vers lo main. 3. Ancrer le cordon dans be support du cordon derrière le tube.
Bb, ATTENTION avant Entretien. Pièces mobiles ! Pour réduire le risque de blessures, ne touchez pas la brosse quand Aspirateur est allumé. . Entrer en contact avec la brosse tandis qu'il tourne ~~ | peut couper, meurtrir ou causer d’aviser dommages. Éteindre et débranchez toujours de lo sortie électrique Faites alimentation en fonctionnant prés de enfants.
CONSEILS DE NETTOYAGE A L'ASPIRATEUR MODE DE BALAYAGE SUGGÉRÉ Afin d’optimaliser le nettoyage, le PowerMate doit Sire poussé droit devant Utilisateur, puis ramené droit derrière. Lorsqu’il a 6% rames, changer lo direction du PowerMate de maniéré & ce qu'il pointe vers la section suivante & nettoyer, Ce mode de balayage doit &hre maintenu sur fout le tupis sec des roulements dents de glissement. XN RELARGUE: Les soupe rapides ef brusques assertive pos un nettoyage complet.
ACCESSOIRES 4h Arrentions NE PAS poser ou enlever le manche ou les tubes droits alors que 'aspirateur est en marche. Cel pourrait causer des étincelles ef endommager les contacts Lectrices. ACCESSOIRES SUR LA MANCHE REMARQUE: §i le PowerMate est fixé, mettre [aspirateur hors tension avant de retirer le manche des tubes. 4 1. Appuyer sur 4 bouton de Sp Bovin de relâchement de 5 relâchement manche et tirer la — da the poignée vers le haut, Sa 2. Glisser les accessoires armement sur le manche, au besoin.
ACCESSOIRES SUR TUBES 1, Pour retirer les tubes du PoworMate bloguer les tubes en position verticale. 2. Avec le pied, appuyer sur la pédale de relâche ef tirer sur les rallonges fout droit vers Ie haut pour les faire sotie du PowerMate. Cédule do drache de ta rallonge 3. Poser les accessoires sur les tubes, gu besson, Voir TABLE D'UTILISATION accessoires (loge 16). 3. 4A tube NG T—— combine I fi A tuba \ am Gui] pour anima p domestiquas © “15.
caractéristiques DE PERFORMANCE Ah AVERTISSEMENT Risque de lésions corporelles Toujours éteindre et débrocher Aspirateur avant de nettoyer lo zone de fa brosse car lu brosse pourrait se rems tire soudainement en marche.
POUR CHANGER LE SAC Pour abstenir de meilleurs résultats de nettoyage, le sor & dépoussiéra doit ire remplacé fréquemment. Indicateur de performance s'allume lorsque le sac a besoin d’être chants ou que le passage d'air est réfréner. REMARQUE: Utiliser le sug de remplacement N* 20-50403. Pour les détails du numéro de pied, consulter PIÈCES détaches [page ). RETIRER LE SAC A POUSSIÈRE 1. Éteindre ef débrancher l’aspirateur. 2. Enlacer le noyau de Aspirateur. (Voir ASSEMBLAGE, page 8). 3.
POUR CHANGER LE FILTRE d’échappement La cartouche de filtre de échappement soir Être remplacé quand il est sale. Remplacer le filtre lorsque la surface entière est recouverte de remuante égale. Ce filtre NE PEUT PAS être lavé tint donné qu'il perdra sa capacité de retenir la poussière, REMARQUE: Liserer les filtres de sortie de remplacement N° 20-40324, Pour les détails du numéral de pièce, consulter PIÈCES détaches (page 6}.
Your Home For troubleshooting, product manuals and expert advice: : @ manageability vow micromanagement For repair in your home of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made i, no matter who sold it For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances arid items like garage door openers and water heaters, 1-B00-4-MY-HOME® Cain anytime, day or night .
