Use & Care Guide Manual de Uso y Cuidado English / Español Model/Modelo: 119.16145210 Item / Artículo: 640-03982741-5 Kenmore Liquid Propane Gas Grill ® Parilla a gas de propane liquido P/N MCDLPTM000 Sears Brands Management Corporation Hoffman Estates, IL 60179 U.S.A www.kenmore.com www.sears.com www.kmart.
If you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. For residential use only. Do not use for commercial cooking. Installation Safety Precautions 1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance. 2.
TABLE OF CONTENTS WARRANTY KENMORE GRILL WARRANTY For Your Safety………………………………………….2 Grill Information Center………………………………....2 Product Record Information……………………………..2 Safety Symbols………………………………………….2 Installation Safety Precautions………………………......2 Kenmore Grill Warranty………………………………...3 Use and Care………………………………………...4-10 Parts List…………………………………………..…11-13 Parts Diagram……………………………………….....14 Assembly……………………………………………15-23 Troubleshooting…………………………………….
USE AND CARE LP Tank NEVER store a spare LP cylinder under or near the appliance or in an enclosed area. Never fill a cylinder beyond 80% full. If the information in the two points above is not followed exactly, a fire causing death or serious injury may occur. An overfilled or improperly stored cylinder is a hazard due to the possible gas release from the safety relief valve. This could cause an intense fire with risk of property damage, serious injury, or death.
LP Tank Exchange Connecting Regulator To The LP Tank 1. LP tank must be properly secured onto the grill. (Refer to assembly section.) 2. Turn all control knobs to the OFF position. 3. Turn LP tank OFF by turning the OPD hand wheel Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their tanks.
For Safe Use of Your Grill and to Avoid Serious Injury: Do not let children operate or play near your grill. Keep pets away from your grill. Keep grill area clear and free from materials that burn. Do not block holes in sides or back of grill. Check burner flames regularly. Use grill only in well-ventilated space. NEVER use in an enclosed space such as a carport, garage, porch, covered patio, or under an overhead structure of any kind.
Safety Tips ▲ Before opening LP cylinder valve, check the coupling nut for tightness. ▲ Before each use, check the gas hose for excessive abrasion or wear, or cuts. Replace a hose assembly showing those signs with the hose assembly specified in the parts list before using the grill. Inspect the hose assembly by following it from the LP tank connection to the gas manifold assembly. ▲ Ensure your grill is located on a level surface and use the adjustable feet (if equipped) as necessary to stabilize.
Turn controls and gas source or tank OFF when not in use. Turning Grill Off If ignition does NOT occur in 5 seconds, turn the burner controls OFF, wait 5 minutes and repeat the lighting procedure. If the burner does not ignite with the valve open, gas will continue to flow out of the burner and could accidently ignite with risk of injury. Igniter Check Turn gas off at LP cylinder. Press and hold electronic ignitor button.
Cleaning the Burner Assembly Stainless Steel Surfaces: To maintain your grill’s high quality appearance, wash with mild detergent and warm soapy water and wipe dry with a soft cloth after each use. Baked on grease deposits may require the use of an abrasive plastic cleaning pad. Use only in direction of brushed finish to avoid damage. Do not use abrasive pad on areas with graphics. o Do not allow dirt and grease to accumulate on stainless steel. o Do not use steel wool as it will scratch the surface.
Storing Your Grill Grilling Tips and Tricks Food cooked on the grill is either done using direct or indirect cooking. Direct cooking is when the food is cooked directly over lit burners. Food is placed inbetween the lit burners for indirect cooking. Direct: Use direct cooking to sear meats. This helps to keep food moist by locking in juices. Some food, such as steak, is first seared using direct cooking, and then finished cooking using the indirect method.
Hardware Pack Listing F A Phillips Head Bolt M6x10mm Grill Transport Handle Heat Shield Qty: 11pcs Qty: 2pcs Part No.:MCDKY18000 Part No.:FP0027 G B Flat Head Bolt M6x25mm Phillips Head Screwdriver Qty: 4pcs Qty: 1 pc Part No. MCDKY15000 Part No.:MCDKY20000 H C Step Head Bolt M6 Battery Size AA Qty: 4pcs Qty: 1 pc Part No.:MCDKY16000 I D Flat Head Bolt M6x12mm Qty: 8pcs Propane Tank Support Ring Hook Part No.:MCDKY17000 Qty: 1 pc Part No.
Parts List Part No Description Key Qty A1 1 HCDLCVA038 Hood Assembly A2 2 *ASMA0014-03 Hood Bolt A3 1 MCDKCVW000 Thermometer B1 1 HCDLBDA148 Firebox Assembly B2 1 SC0096 Gas Manifold Assembly B3 2 S7007-026D-018 Shelf Right Front / Left Back Support B4 2 S7007-026D-017 Shelf Left Front / Right Back Support B5 1 S1036-026D-016 Control Panel Left Support B6 1 MCDKADD000 Regulator and Hose Assembly B7 1 S1036-026D-017 Control Panel Right Support B8 3 SD0050-A "I"
Parts List Key Qty Part No Description C4 1 HCDKBTA048 Cabinet Bottom Base C5 2 FE0080 Wheel C6 2 FE0154N Adjustable Foot C7 1 S4061-000B-001 Propane Tank Support Chain Hook C8 1 SE0232-001 Propane Tank Support Chain C9 1 MCDKADA025 Gas Manifold Bracket C10 1 MCDKFRH015 LP Tank Bracket C11 1 MCDKADG000 Regulator Hose Support Chain D1 1 HCDKTBJ035 Left Shelf Assembly D2 1 HCDKTBL035 Right Shelf Assembly D3 1 MCDKTBK035 Shelf Left Control Panel D4 1 MCDKTBM03
Parts Diagram 14
Assembly Instruction 1 Install Cabinet Left Side and Right Side Panels Attach Cabinet Left and Right Side Panels to the Cabinet Base using 6 Phillips Head Bolts (M6x10mm). Do not fully tighten bolts at this time. Phillips Head Bolt M6x10mm Qty: 6 2 Install Cabinet Front Panel and LP Tank Bracket Attach Cabinet Front Panel to the Cabinet Left and Right Side Panels using 4 Washer Head Bolts (M4x10mm) at the top and bottom holes.
3 Attach Propane Tank Support Chain and Propane Tank Support Chain Hook Attach the Propane Tank Support Chain to Cabinet Left Side Panel using 1 Washer Head Bolt (M4x10mm). Attach the Propane Tank Support Chain Hook to Cabinet Right Side Panel using 1 Washer Head Bolt (M4x10mm). Propane Tank Support Chain Hook Qty: 1 Washer Head Bolt M4x10mm Qty: 2 4 Install Hood and Firebox Assembly Remove Regulator and Hose Assembly from underside of Hood and Firebox Assembly.
5 Attach Hood and Firebox Assembly to Cabinet Assembly and Install the Regulator Hose Support Chain Attach the Hood and Firebox Assembly to the front of the Cabinet Side Panels using 2 Phillips Head Bolts (M6x10mm). Attach the Regulator Hose Support Chain (located on the regulator hose) to the back of the Cabinet Side Panel using 1 Washer Head Bolt (M4x10mm).
7 8 Install Control Knobs Press 3 Control Knobs onto the valve stems as shown. Install Side Shelf Supports to Firebox Assembly Attach Side Shelf Right Front and Back Supports to Firebox Assembly using 4 Flat Head Bolts (M6x12mm). Repeat same procedure to attach Side Shelf Left Front and Back Supports to Firebox Assembly. Note: Position the Supports so that the pins are at the bottom of the supports and extend towards the center of the firebox.
9 Attach Side Shelves Position the Shelf Brackets to the inside of the Shelf Supports in the grill storage position. Attach Left and Right Shelves to Shelf Supports with 2 Step Bolts (M6) each. Securely tighten. Step Bolt M6 Qty: 4 10 Side Shelf Operation Pull up on the Left Side Shelf and slide down over the support pins to secure in the upright position. To lower, slide shelves up and fold down into storage position.
11 Install Heat Diffusers, Cooking Grates, Warming Rack Insert Heat Diffusers into the firebox by placing them into the indentations along the front and back of the firebox. See Figure 1. Place the Cooking Grates into the firebox with the Grate finger holes at the front. See Figure 2. Insert the Warming Rack into the slots of the firebox side panels as shown. See Figure 3.
12 Install Grill Transport Handle Attach Grill Transport Handle and 2 Handle Heat Shields to the back of the firebox using 4 Flat Head Bolts (M6x25mm). Transport Handle Heat Shield Qty: 2 Flat Head Bolt M6x25mm Qty: 4 13 Place and Secure LP Cylinder into the Cabinet Be sure the LP cylinder is “Off” by turning the hand wheel clockwise until it stops. Be sure all burner control knobs are turned to the “Off” position.
14 Install Battery Unscrew the Electronic Igniter Button. Place the “AA” Battery into the igniter with the positive (+) end up. Screw the button back into place. Battery (Size AA) Qty: 1 Do not dispose of batteries into fire as they may leak or explode. 15 Congratulations! Assembly is now complete! Remove any additional labels or packing material from the grill except the CSA and Safety labels. Be sure to clean all foam packing material out of all areas.
16 Grill Transport Grasp grill transport handle with one hand (1) and grill hood handle (2) with the other from behind the grill. Place foot against back of base (3) for leverage. Tilt grill back onto wheels to transport. Once grill is in desired location, level if necessary by rotating adjustable feet (4) clockwise to raise or counterclockwise to lower. CAUTION: Grill must be completely cooled down before transporting.
EMERGENCIES: Emergencies Gas leaking from cracked/cut /burned hose. Gas leaking from LP cylinder. Gas leaking from LP cylinder valve. Gas leaking between LP cylinder and regulator connection. Fire coming through control panel. Grease fire or continuous excessive flames above cooking surface. If a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. Possible Cause Prevention / Solution Damaged hose.
TROUBLESHOOTING (continued) Problem Possible Cause Burner(s) will not light using ignitor. Burner(s) will not match light. Prevention / Solution Wire and/or electrode covered with cooking residue. Wires are loose or disconnected. Wires are shorting (sparking) between ignitor and electrode. Dead battery. Faulty electronic ignition circuit. Reconnect wires or replace electrode /wire assembly. Replace ignitor wire /electrode assembly.
PELIGRO PRECAUCIÓN Si detecta olor a gas: 1. Corte el suministro de gas al aparato. 2. Apague cualquier llama. 3. Abra la tapa. 4. Si el olor no desaparece, manténgase alejado del aparato y llame inmediatamente a la compañía del gas o a los bomberos. Sólo para uso residencial. No la utilice para cocina comercial. Precauciones de seguridad de la instalación Utilice esta barbacoa, según la ha comprado, con gas LP y el conjunto de regulador/válvula suministrado.
ÍNDICE Para su seguridad ........................................................................ 26 Centro de información de barbacoas ...................................... 26 Información sobre el producto .................................................. 26 Símbolos de seguridad ............................................................... .26 Precauciones de seguridad para la instalación .................... .26 Garantía de barbacoa Kenmore ..............................................
Botella de propano líquido La botella de propano líquido utilizada con su barbacoa debe cumplir los siguientes requisitos: Utilice sólo botellas de propano líquido con las medidas necesarias: 12” (30,5 cm) (diámetro) x 18” (45,7 cm) (altura) con 20 lb. (9 kg.) de capacidad máxima. Las botellas de propano líquido deben fabricarse y marcarse de acuerdo con las especificaciones para botellas de propano líquido del Departamento de Transportes de EE.UU.
Cambio de botella de propano líquido Muchos minoristas que venden barbacoas ofrecen un servicio de recogida y venta de botellas de propano líquido. Utilice sólo empresas con buena reputación, que inspeccionen las botellas, y las llenen con precisión, las comprueben y dispongan de botellas certificadas. Cambie su botella sólo por otra equipada con la función de seguridad OPD, según se describe en la sección "Botella de propano líquido" de este manual.
PELIGRO ADVERTENCIA No introduzca ninguna herramienta u objetos extraños en la salida de la válvula o la válvula de descarga de seguridad. Podría dañar la válvula y causar una fuga. Las fugas de propano pueden causar explosiones y lesiones graves o mortales. Si detecta una fuga, PARE y llame a los bomberos. Si no puede detener una fuga de gas, cierre inmediatamente la válvula de la botella de propano líquido y llame a un distribuidor de gas LP o a los bomberos.
Consejos de seguridad ▲ Antes de abrir la válvula de la botella de propano líquido, compruebe que la tuerca de acoplamiento se haya apretado correctamente. ▲ Antes de cada uso, compruebe la manguera, revisando que no presente abrasión, desgaste o cortes. Cambie la manguera dañada por la especificada en la lista de piezas antes de utilizar la barbacoa. Inspeccione el estado de la barbacoa desde la conexión de la botella de propano líquido hasta el conjunto del regulador de gas.
HI (alto) ADVERTENCIA LOW (bajo) Ponga los mandos y la fuente o botella de gas en apagado (OFF) cuando no esté utilizando la barbacoa. Apagado de la barbacoa Ponga todos los mandos en APAGADO (OFF). CIERRE la botella de propano líquido girando la rueda manual en la dirección de las agujas del reloj hasta el tope. Comprobación del encendido Cierre el gas de la botella de propano líquido. Mantenga pulsado el botón de encendido electrónico.
Limpieza del conjunto del quemador Siga estas instrucciones para limpiar o cambiar piezas del conjunto de un quemador o si tiene problemas para encender la barbacoa. 1. Cierre el paso de gas de los mandos de control y la botella de propano líquido. 2. Quite las parrillas de cocinar y los difusores de calor. 3. Quite los tornillos de cabeza Phillips situados en el extremo trasero de cada quemador. 4. Levante los quemadores y suéltelos. Desenchufe el encendedor electrónico del electrodo.
Guardar la barbacoa Limpie las parrillas. Guárdela en un lugar seco. Retire la pila del encendido electrónico. Si la botella de propano líquido está conectada a la barbacoa, deberá guardarse al aire libre en un espacio con buen ventilación y fuera del alcance los niños. Puedeguardar la barbacoa en el interior SÓLO si la botella de propano líquido está cerrada, desconectada y retirada de la barbacoa. La botella de propano líquido debe dejarse al aire libre. Tape la barbacoa.
Lista de piezas incluidas F A Tornillo de cabeza Phillips M6x10mm Protector contra el calor del asa de transporte de la barbacoa Cant.: 11 unid. Cant.: 2 unid. Nº de pieza: MCDKY18000 Nº de pieza: FP0027 B G Tornillo de cabeza plana M6x25mm Cant.: 4 unid. Destornillador Phillips Nº de pieza: MCDKY15000 Cant.: 1 unid. Nº de pieza: MCDKY20000 C H Tornillo escalonado M6 Cant.: 4 unid. Pila de tamaño AA Nº de pieza: MCDKY16000 Cant.: 1 unid.
Lista de piezas Clave Cant.
Lista de piezas Clave Cant.
Despiece 38
Instrucciones de montaje Instale el panel izquierdo y el derecho del armario Fije los paneles izquierdo y derecho a la base del armario mediante 6 tornillos de cabeza Phillips (M6x10mm). No los apriete completamente. Tornillo de cabeza Phillips M6x10mm Cant.
Coloque la cadena del soporte de la botella de propano y el gancho de la cadena. Fije la cadena del soporte de la botella de propano al panel del lado izquierdo del armario con un tornillo de cabeza de arandela (M4x10mm). Fije el gancho de la cadena del soporte de la botella de propano al panel del lado derecho del armario con un tornillo de cabeza de arandela (M4x10mm). Botella de propano Cadena de soporte Gancho Cant.: 1 Cabeza de arandela Tornillo M4x10mm Cant.
Coloque la tapa y el cuerpo en el armario e instale la cadena de soporte de la manguera del regulador Fije la tapa y el cuerpo a la parte frontal de los paneles laterales del armario mediante 2 tornillos de cabeza Phillips (M6x10mm). Coloque la cadena de soporte de la manguera del regulador (situada en la manguera del regulador) en la parte trasera del panel lateral del armario con 1 tornillo de cabeza de arandela (M4x10mm). Cabeza Phillips Tornillo M6x10mm Cant.
Instale los mandos de control Presione los dos mandos de control sobre los pies de las válvulas tal y como se muestra. Instale los soportes del estante lateral en el cuerpo Coloque los soportes delantero y trasero del estante derecho en el conjunto del cuerpo con 4 tornillos de cabeza plana (M6x12mm). Repita el mismo procedimiento para montar los soportes delantero y trasero del estante izquierdo en el conjunto del cuerpo.
Monte los estantes laterales Coloque los estantes laterales hacia el interior de los soportes en la posición de almacenaje de la barbacoa. Fije los estantes izquierdo y derecho a los soportes de los estantes con 2 tornillos escalonados (M6) cada uno. Apriete con fuerza. Tornillo escalonado M6 Cant.: 4 Funcionamiento del estante lateral Tire hacia arriba del estante lateral izquierdo y deslícelo hacia abajo sobre los pasadores en posición recta.
Instale los difusores de calor, las parrillas para cocinar y las rejillas para calentar Introduzca los difusores de calor en el cuerpo colocándolos en las hendiduras a lo largo de la parte delantera y trasera del cuerpo. Ver figura 1. Coloque las parrillas en el cuerpo con los orificios para los dedos en la parte frontal de la parrilla. Ver figura 2. Introduzca la rejilla para calentar en las ranuras de los paneles laterales del cuerpo, como se muestra. Ver figura 3.
Instale el asa de transporte de la barbacoa Fije el asa de transporte y los 2 protectores de calor del asa a la parte trasera del cuerpo mediante 4 tornillos de cabeza plana (M6x25mm). Asa de transporte Protectores de calor Cant.: 2 Tornillo de cabeza plana M6x25mm Cant.: 4 Coloque y asegure la bombona de propano en el armario Asegúrese de que la bombona de propano está “APAGADA” girando el mando en dirección de las agujas del reloj hasta que haga tope.
Instale la pila Afloje el botón del encendedor electrónico. Coloque la pila "AA" en el encendedor con el polo positivo (+) hacia arriba. Vuelva a apretar el botón. Pila (Tamaño AA) Cant.: 1 ADVERTENCIA No tire las pilas al fuego, porque podrían explotar o producirse fugas. ¡Enhorabuena! Ya ha montado su barbacoa. Quite cualquier etiqueta adicional o material de embalaje de la barbacoa, excepto las etiquetas CSA y de seguridad. Asegúrese de eliminar la espuma de embalaje de todas las zonas.
Cómo transportar la barbacoa Sujete el asa de transporte con una mano (1) y el asa de la tapa (2) con la otra desde detrás de la barbacoa. Coloque el pie contra la parte trasera de la base de la barbacoa (3) para levantarla. Incline la barbacoa hacia atrás sobre las ruedas para su transporte. Cuando la barbacoa esté en la posición deseada, nivélela si es necesario girando los pies ajustables (4) en la dirección de las agujas del reloj para subir y en la dirección opuesta para bajar.
EMERGENCIAS: Si no se puede detener una fuga de gas, o si se produce un incendio debido a una fuga de gas, llame a los bomberos. Emergencias Causa posible Prevención / Solución Fuga de gas de una manguera agrietada / cortada / quemada. Manguera dañada. Cierre el gas de la botella de propano o de la fuente en un sistema de gas natural. Para cualquier otra causa, cambie la válvula / manguera / regulador.
SOLUCIÓN DE PROBLEMAS (continuación) Problema No se enciende el quemador o quemadores con el encendedor. Causa posible Prevención / Solución Cable y / o electrodo cubiertos con residuos de alimentos. Limpie el cable y / o electrodo con alcohol y un algodón. Los cables están sueltos o desconectados. Vuelva a conectar los cables o sustituya el conjunto de electrodo / cable. Los cables se cortocircuitan (chispas) entre el encendedor y electrodo. Pila agotada.
Get it fixed, at your home or ours! Your Home For troubleshooting, product manuals and expert advice: www.managemylife.com For repair – in your home – of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories and owner’s manuals that you need to do-it-yourself. For Sears professional installation of home appliances and items like garage door openers and water heaters.