Manual

ManualsBrandsKenmore ManualsSewing MachineOfficial Kenmore sewing machine

NODELS

158.13400, .1340180

153.13460, .1345180

156.1364)0, .13SO1DO

iS8.1356000

uJ';'cWnIre'u, I

[ :E_ER,I L_.R I.....s,.o---

PIIFHERFOOTNEHINT

_ mlm_E SOt_ONI41KnAIl1_

o2 aim

FRt_NTFACING SHUTTLE SIDEFACINGSHUTTLE

IHJPKRHiONBAR LOWBAR

NI6H BAR LOWBAR

FId_URE4.!

DISTRIBUTION OF NEEDLE SWING

CHECKNEEDLE POSITION AT STRAIGHT STITCHING BEFORECHECKIN6 DISTRIBUTION OF NEEDLE

SHI'NGMENTIONEDOELOM.

SET THE SPECIAL STITCH SELECTORDIAL AT ZIGZAG POSITION AND STITCH NIDTH CONTROL

AT 4. TUF_N}'NGTHE HAND MREL, CHECKAND SEE IF THE NEEDLEGOES THROUGHTHE NEEDLE

SLOT AT POINTS EQUAL DISTANCE FRON EACH ENO OF THE NEEDLESLOT.

ZF A_U.eTHENT IS NEEDED, LOOSENSCNEHB AND ADv_JSTSCREHA TO GET CORRECTNEEDLE

SNING. AFTER AOJUSTIqENT,TIGHTEN SCREHD' SECURELY.

FIGUREC-25

Summary of content (13 pages)

PAGE 1
NODELS 158.13400, . 1340180 153.13460, .1345180 156.1364)0, .13SO1DO iS8.1356000 I DISTRIBUTION OF NEEDLE SWING [ Ire'u, :E_ER,Iu J';'cWn L_.R I.....s,.o--- I CHECKNEEDLE POSITION AT STRAIGHT STITCHING BEFORECHECKIN6 DISTRIBUTION OF NEEDLE SHI'NG MENTIONED OELOM. PIIFHERFOOTNEHINT _ mlm_E SOt_ONI41KnAIl 1_ SET THE SPECIAL STITCH SELECTOR DIAL AT ZIGZAG POSITION AND STITCH NIDTH CONTROL AT 4.
PAGE 2
NEEDLEPOWTION riotamUtdn ,iddlllJeeaUdmO.lbnqx_odmo moodJo Pkml (19 FOR FRONT FACINO SHUTTLE NOOELS, PLACE GHUGEAT POSITION AS XLLUSTRATEDgITH THE NO-GO-SIDE OF THE GAUGE FACING THE NEEDLE PLATE. LOMERPRESSERFOOT. MtXL[ TURNXNGTHE HAROMHEELSLOMLYBY HAllO, THE GAUGESHOULDBE MOVEDBY THE FEEl) DOG TEETH. IF NOT, FEED DOG TEETH ARE TOO LOM. THEN PLACE THE GAUGEUP-SXDE-D(MI WITH THE 6R-SIDE FACING THE NEEDLEPLATE. REPEAT THE SAME PROCEDURE. THE GAUGESHOULD NOT BE MOVED.
PAGE 3
ZERO.FEEDING NEEDLETIMING TO SHUTTLE NEEDLEBAR HEIGHT CHECKING 1) SET STITCH PATTERN SELECTORAT STRAIGHT STITCHING. ii PLACE PAPER ON THE NEEDLE PLATE. sETSTXTC. LENGTH CONTROL "o'. CHECKAND SEE IF THE FEEl) .T DOGMOVESNHEN TURNING THE REVERSE STITCH CONTROLCLOCKMISEAND NHEN RELEASING THE CONTROL. AT "O" POSITION THF FEED DOGSHOULDNOT MOVE IN EITHER CASE. IF IT DOES, ADJUST-. HINT IS NEEDED. REMOVETDLER PULLEY SET. LOOSENSCREHS (A) AND (B) SLIGHTLY AND INSERT THE ECCENTRIC TOOl.
PAGE 4
ZIGZAG NEEDLE TIMINGTO OHU LE De net elleaqNm Ik_ m. If. by_ d_m_l th_ e _ &l120. edw dNmshoneqNcifiedin _ Im_w.nl_lImbc_k_etit is is o_ ot mlij _, heedk i_ Radial T.indng GatlgeirlstructJo118 SET STITCH WIOTH CONTROLAT MAXIMUM ZIGZAG POSITION. TURN HANOMHEEL,OBSERVINO THAT I J Use FRONT6.8 . THE NEEDLEGOES STRAIGHT UP MITH NO SIDE MOVEMENTTO A POINT 2-3 144 ABOVE THE NEEDLE PLATE. AT THIS POINT THE NEEDLE SH sIDE..GIN TO SWI TO OTHER VERIFY TH;TTHENEEOLE _ES STRAIGHT DOMNAT THE OTHERSIDE. I.
PAGE 5
AUTOMATIC Im/ERSE STITCHING IrrRETCH STITCH AUTOMATIC REVERIIEITITCHING BUTTONHOLE SET SPECIAL STITCH SELECTORDIAL OR KNOB AT ZIGZAG STRETCH STITCHING AND STITCH NZDTH CONTROLAT "4" AND STITCH LENDTH CONTROLAT "6". IF HACHINE HAS H(X)IFIER FOR STRETCHSTITCH, SET IT AT THE CENTER BETWEEN"L" AND "S" POSITION. CHECK ZERO FEEDING BEFORECHECKIII6 AUTOI_TIC FOIWARDAND REVERSE STITCH FOR BIITTONHOLE. SET STITCH LENGTH CONTROLAT GREEN ZONE. ATTACH BUTTONHOLESHOE. CHECK AND SEE IF THE LENGTH OF REVP2 _.
PAGE 6
Avl mlk Clmmd STITCH WIDTH SET STITCH SELECTOR AT THE MIDEST ZIGZAG STITCH. CHECK TO SEE IF THE ZIGZAG BITE IS AS SPECIFIED FOR THIS MODEL. IF NOT, LOOSEN SCREH (k) AHD INSERT THE ECCENTRIC TOOL INTO HOLE (B). TURN THE ECCENTRIC TOOL IN EITHER DIRECTION UNTIL YOU GET THE SPECIFIED MIDTH. 'r,- ITEN SCREW(A) SECURELYAFTER ADdUSTMENT. C SET SPECIAL STITCH SELECTORDIAL OR KNOB M ZIGZAG POSITION. CHECK TO SEE IF THE CAM FOI.LOM[R (B) ALIGNS PROPERLYMITH Z|GZAG CN| (C, THIRD DISC FROMBACK).
PAGE 7
THIS PAGE INTENTIONALLY LEFT BLANK THIS PAGE INTENTIONALLY LEFT BLANK
PAGE 8
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT
PAGE 9
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT
PAGE 10
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT
PAGE 11
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT
PAGE 12
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT
PAGE 13
THIS PAGE INTENTIONALLY BLANK THIS LEFT PAGE INTENTIONALLY BLANK LEFT