Quick Start Manual

ManualsBrandsKenmore ManualsOvensKenmore 31053

iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER.

iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR S USE.

READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE.

If the information in this manual is not followed exactly, a fire

or explosion may result causing property damage, personal injury or death. "--_s __-LU-->_ _

FOR YOUR SAFETY:

-- Do not store or use gasoline or other flammable vapors and liquids in

the vicinity of this or any other appliance.

-- WHAT TO DO IF YOU SMELL GAS:

* Do not try to light any appliance.

Do not touch any electrical switch; do not use any phone in your

building.

* Immediately call your gas supplier from a neighbor's phone. Follow the

gas supplier's instructions.

If you cannot reach your gas supplier, call the fire department.

-- Installation and service must be performed by a qualified installer,

service agency or the gas supplier.

Appliances Installed in the

state of Massachusetts:

This Appliance can only be installed

in the state of Massachusetts by a

Massachusetts licensed plumber or

gasfitter.

This appliance must be installed

with a three (3) foot / 36 in. long

flexible gas connector.

A"T" handle type manual gas valve

must be installed in the gas supply

line to this appliance.

1 1/2" Max.

Shave Raised (3.8 cm Max.)

Edge to Clear

Space for a

311/2"min

(80 cm)

Wide

Cooktop.

See Dimension

C in table.

These surfaces should

be fiat & leveled

(hatched area)."-_

5" Min.

(12.7 em Min.)

From Wall Both Sides

30" Min.

(76.2 cm Min.)

13 vw

(see Note 3) 18" Min. (33 cm)

(45.7 cm) Min.

Locate Cabinet Doors

1" (2.5 cm) Min. from

Cutout Opening.

IMPORTANT: Cabinet and countertop

width should match the cutout width.

Do nat install the unit in the cabinet before reading next 2 pages.

35 7/8" (9].]cm) - 30" 31 1/2" 28 5/16" 30_+1/16"

36 5/8" (93cm) (76.2cm) (80cm) (71.9cm) (76.2-I-0.15cm)

NOTE: Wiring diagram for these appliances are enclosed in this booklet.

Min.

(61 cm Min.)

Printed in Canada

21 3/4" (55.2cm) Min.

i 22 1/8" (56.2cm) Max 36 5/8" (93cm) Max.

24" (61cm) Min. with 35 7/8" (91.1cm)

backguard

P/N 318201693 (1010) Rev. A

English - pages 1-14

Espa_el - paginas 15-27

Wiring Diagrams - page 28

Summary of content (28 pages)

PAGE 1
iNSTALLATiON AND SERVICE MUST BE PERFORMED BY A QUALiFiED iNSTALLER. iMPORTANT: SAVE FOR LOCAL ELECTRICAL iNSPECTOR S USE. READ AND SAVE THESE iNSTRUCTiONS FOR FUTURE REFERENCE. If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or death. FOR YOUR SAFETY: --* * -- Do not store or use gasoline or other flammable vapors and liquids the vicinity of this or any other appliance.
PAGE 2
NOTES: Do not pinch the power supply cord between the range and the wall. Do not seal the range to the side cabinets. 24" 0 (61 cm) minimum bottom of wood millboard 0.024" clearance or metal covered with For cutouts Allow below 22 7/8"(58.1 and the bottom by not less than No. 28 MSG or 0.020" clearance the cooktop is protected not less than (0.6 mm) aluminum, 30" (76.2 cm) minimum between cabinet 1/4" sheet metal, of the cabinet (0.64 0.015" (0.
PAGE 3
To avoid breakage: Do NOT handle or manipulate the unit by the cooktop. The counter-top around the cut-out should be fiat (see hatched area on illustration 1). and leveled Before installing the unit, measure the heights of the two (2) cabinet sides (H1-4), front and back (see illustration 1) from the floor to the top of the counter.
PAGE 4
important Notes to the installer 1. Read all instructions contained in these installation instructions before installing range. 2. Remove all packing material from the oven compartments before connecting the gas and electrical supply to the range. 3. Observe all governing codes and ordinances. 4. Be sure to leave these instructions with the consumer. . Note: For operation at 2000 ft. elevations above see level, appliance rating shall be reduced by 4 percent for each additional 1000 ft.
PAGE 5
Before Starting Tools you will need For leveling • Adjustable • 5/16" Nutdriver • Electric Drill legs and antl-tip brackets: wrench or channel lock pliers _-._ _"_,_i-\, ......._s_ .... or Flat Head Screw Driver Drill & 1/8 Diameter Bit (5/32" Bit if installing Masonry Drill Formed in concrete) • Level & Measuring For gas supply • Pipe Wrench • Brush 3I_/2".._ (81 cm) _ ¾" Tape back at front trimmed corners of countertop opening.
PAGE 6
* If you are using the line protector allow access for e We recommend the floor or wall the installation. a through the floor gas entry, remove shield from the bottom of the unit to the pipe line (figure 3). to install a pipe elbow right out of towards the center of the unit to ease | Connect the range to the gas supply Important: Remove all packing material and literature from range before connecting gas and electrical supply. To prevent leaks, put pipe joint sealant on all external pipe threads.
PAGE 7
Once regulator is in place, open the shutoff valve in the gas supply line. Wait a few minutes for gas to move through the gas line. Grounding IMPORTANT from gas connections. Checking may result in a fire or explosion.
PAGE 8
Range installation Important installation Adjust leveling cooktop Note: Door removal is not a requirement for of the range, but is an added convenience. screw in (refer equipped Refer to the Use and Core Guide for oven door removal instructions. leg leveling Figure 6 Installation _]_The range cooktop overlaps the countertop at the sides and the range rests on the floor. The cooktop is 31 1/2" _lnstall cabinet doors 31" (78.7 cm) rain. apart will not interfere with range door opening.
PAGE 9
Leveling the Range Models Equipped Models Equipped with Leveling Device Level the range after installation in the cutout opening. 1. Open the range drawer. The leveling screws control the height of the rear leg. 2. Adjust the appliance legs as follows until the underside of the cooktop (or cooktop glass) surface is sitting level on the countertop (Figure 7). a.To adjust the front legs_ use a wrench on the leg base and turn counterclockwise to lower or clockwise to raise the range. b.
PAGE 10
the slotted Check Operation Refer to the Use and Care Guide packaged with the range for operating instructions and for care and cleaning of your range. Remove all packaging from the oven before testing. . Install This range shown (see Burner Bases is equipped Figure and with Burner sealed Caps burners screw inside. Flame size can be increased or decreased with the turn of the screw. Adjust flame until you can quickly turn knob from HI to LOWEST POSITION without extinguishing the flame.
PAGE 11
Operation of Oven Burners and Adjustments 11.6.1 Electrlc ignition Burners Operation of electric igniters should be checked range and supply line connectors have screws at rear of oven bottom. Pull up at rear, disengage front of oven bottom from oven front frame, and pull the oven bottom out of the oven. Remove burner baffle so that burner flame can be observed. Oven been after If the flame is yellow, increase air shutter opening size (see "2" in Figure 14).
PAGE 12
Anti-Tip Instructions | Brackets 2. Unfold paper template and place it fiat on the floor with the right rear corner positioned exactly on the intersection of the center and back lines you just drew before. (Use the diagram below to locate brackets if template is not available (Figure 15)). 3. Mark on the floor the location of the 4 mounting holes shown on the template. For easier installation, 3/16"(0,48 cm) diameter pilot holes 1/2"(1,27 cm) deep can be drilled into the floor. 4.
PAGE 13
| Models Equipped with Leveling 1. iec_ To reduce the risk of tipping of the range, the range must be secured to the floor by properly installed anti-tip brackets and screws packed with the range. These parts are located in a plastic bag in the oven. Failure to install the anti-tip brackets wiii allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself.
PAGE 14
PAGE 15
LA INSTALACION Y ELSERVICIO DEBEN SEREFECTUADOSPOR UN INSTALADOR CALIFICADO. IMPORTANTE: GUARDE ESTASINSTRUCCIONESPARAUSO DELINSPECTORLOCAL DE ELECTRICIDAD. LEAY GUARDE ESTASINSTRUCCIONESPARA REFERENCIAFUTURA. Si la informaci6n contenlda en este manual no es seguida exactarnente, puede ocurrir un incendio o explosi6n causando da_os rnateriales, lesi6n personal o la rnuerte.
PAGE 16
NOTAS: O No peJJizque O No selle la estufa Un espacio cuando eJ cord6n a minimo el fondo eJ_ctrico los armarios entre Ja estufa de lado. de 24" (61 cm) entre del armario y Ja pared. de madera la superficie o metal de la estufa est6 protegido y el rondo del armario pot no menos de 1/4" de madera resistente al fuego cubierta pot una 16mina met6lica de MSG, n0mero mm) de acero inoxidabie, 0.024" (0.6mm) aluminio, 6 0.020" (0.5mm) de cobre. Un espacio minimo de 30" (76.
PAGE 17
Para evitar ffactura unidad sosteniendo de la unidad: NO manipule la la cubierta. La cubierta alrededor del espacio donde usted instalara su unidad debe de estar plana y niveJada. (Vea el 6rea sombreada en la ilustraci6n nOmero 1). Antes de instalar la unidad, mida la altura de los dos (2) lados de los gabinetes (H1-4), frente y parte trasera (vea ilustraci6n 1) del piso a Io alto de la cubierta.
PAGE 18
Notas importantes para el instalador 1. Lea todas las instrucciones contenidas antes de instalar la estufa. 2. Saque todo el material usado en el embalaje del compartimiento del horno antes de conectar el suministro el_ctrico o de gas a la estufa. Observe todos los c6digos y regiamentos pertinentes. Deje estas instrucciones con el comprador. Nota: Para la utilizaci6n a m6s de 2 000 pies de aitura, la potencia del aparato deber6 ser reducida de 4 por ciento a cada 1 000 pies adicionales. 3. 4. 5.
PAGE 19
Antes de comenzar Herramientas que va a necesitar Para paras de nivelaci6n y monfura • Llave ajustable o alicates • Llave para apretar tuercas de 5/16" destornillador de cabeza plana • Taladro el_ctrico y una broca de 1/8" (broca de taladro de hormig6n de 5/32" si se instala sobre hormig6n) • Nivel & Cinta de medici6n Para la conexi6n al sumlnistro anti=vuelco: ...._,_ _iy, _,_ o un -.......................... (81 cm) __ (1.
PAGE 20
° Siesta usando una salida de piso de gas, remover ia protecci6n de la linea de la parte de aba]o de la unidad pare permitir ei acceso pare ia tuberia de gas (Fig 3). ° Recomendamos instaiar un code de ia tuberia tan pronto saiga dei piso o de ia pared ei centre de ia unidad pare faciiitar aline6ndoio instaiaci6n. Eli Conecte la estufa al suministro de gas Importente: Quite todo el material de embalaje y literature de la estufa antes de conectar el gas y la fuente el_ctrica.
PAGE 21
Instrucciones de puesta a tierra Una vez que regulador est6 en su lugar, abra la v61vula en la Ifnea del suministro de gas. Espere algunos minutos para que el gas pueda moverse a trav_s de la Ifnea de gas. IMPORTANTE Par favor lea con cuidado. Para la segurldad personal, este aparata puesto a tlerra apropladamente. Compruebe para saber sl hay fugas de gas. Despu_s de conectar Ja estufa con Ja fuente de gas, compruebe el eJectrodom_stico para saber si hay fugas con un man6metro.
PAGE 22
| lnstalaci6n | de la estufa Aiusfe aias pates de niveiaci6n de manera que ia parte de abajo de ia plancha de cocinar est6 apoyada contra ei mostrador. Atornille con cuidado en ia pate de niveiaci6n trasera haste qua ei vidrio que est6 coicjado toque ievemente ia cubierta. Ei vidrio debe soportar ei peso de ia unidad. Luego, atornille con cuidado en ias dos pates de niveiaci6n anteriores (icjuai a 15) haste que ei vidrio que est6 coigado toque ievemente ia cubierta.
PAGE 23
Nivelaci6n | Para los modelos equipado paras niveladoras. de la estufa Para los rnodelos equipado con un sistema de disposifivo de nivelaci6n. Nivele la cacina despu_s de haberla abertura del mastradar. Nivele la esufa V ajuste la altura de la estufa antes de instalarla en la abertura. instalada en la 1. Abra la gaveta. Las tornillos de nivelaci6n controlar la altura de las paras traseras. 2.
PAGE 24
J[Jl Cornprobaci6n 3. Inmediatarnente cambie ia hornilla en la que est6 trabajando de la posici6n ALTO ("HI") a la posici6n M,_,S BAJO. del funcionarniento Consuite el Manual del Usuario incluido con la estufa para instrucciones de operaci6n y instrucciones para ei cuidado y iirnpieza de su estufa. Quite todo ei ernbalaje de ia unidad antes 4.
PAGE 25
Operaci6n de Quemadores de Homo Para retirar del Homo y Ajustes arriba, 11.6.1 Quemadores La operaci6n despu6s de ignici6n el_ctrica de los encendores de que la cocina suministro el_ctricos revisada haya sido conectada control elSctrico homo asf como el6ctrico. de asado Si la llama central superior, el6ctrico. ajustes. Cuando aparecer6 tiempo de Para ajustar ariba), con un encendedor de cierre. suficiente en el quemador del homo. despu6s y antes de que la llama del horno.
PAGE 26
Instrucciones de instalaci6n fijaci6n anti-indinaci6n de la Para los modeios equipado con un sistema de diposifivo de nivelaci6n. Para reducir el riescjo de indinaci6n de la cocina, 6sta debe ser asecjurada hacia el piso con las fijaciones de anti-inclinaci6n y los tornillos que vienen con la cocina. Estos componentes se encuentran en el horno. Si no instala las fijaciones, corre el riescjo que su cocina pueda inclinarse si pone demasiado peso en ella o si un ni_o sube sobre 6sta.
PAGE 27
| Para los rnodelos equipado paras 1. con las niveladoras. Para reducir el riescjo de inciinaci6n de la cocina, _sta debe ser asecjurada hacia el piso con las fijaciones de anti-inciinaci6n y los tornillos que vienen con ia cocina. Estos componentes se encuentran en ei horno. Si no instaia ias fijacioneso corre ei riescjo que su cocina pueda inciinarse si pone demasiado peso en ella o si un ni_o sube sobre 8sta.
PAGE 28
[] OVEN CIRCUIT//CIRCUITO DE HORNO//CIRCUIT FOUR W-6 • W-14 C2 i IELECTRONZC OONVRCI]ON MOTOR VENTILADOR DEL _OTEUR ,VOTORCONVECCION/ VENTILATEUR oR,w.s CONVECTION <¢_ OVEN CONTROL/ R-6 I, CONTROL DE HORNO ELECTRONZCO/ ICONTROLE ELECTRONIQUE FOUR IES 5XX FAN/ BR_!_ _ 0,0.....