Range Hood Use & Care Guide Installation Manual 31130 (30” wide - Stainless) 31133 (36” wide - Stainless) ENGLISH Models HB0108 09030 rev. A SEARS CANADA INC., Toronto, Ontario M5B 2B8 www.sears.
READ AND SAVE THESE INSTRUCTIONS TABLE OF CONTENTS SECTION.................................................................. PAGE(S) Warranty ................................................................................2 Safety Instructions .................................................................2 Operation ...............................................................................3 Cleaning ................................................................................
OPERATION Always turn ON your hood before you begin cooking in order to establish an air flow in the kitchen. Let the blower run for a few minutes to clear the air after you turn off the range. This will help keep the whole kitchen cleaner and brighter. Nigthlight switch Press this switch once to turn on the nightlight. Press this switch once more to shut off the nightlight.
PARTS INCLUDED WITH HOOD PARTS INCLUDED WITH HOOD Aluminum grease filters (2 per hood) HR0010 HR0051 Parts Bag including: 5 no. 8 x 1½” countersunk screws 8 no. 8 x 3/4” screws 6 no. 8 x 3/8” screws 6 Drywall anchors 3 Washers HR0012 120 V, 50 W, PAR 16 with GU10 base shielded halogen lamp (2 per hood) Sears Part No.
RANGE HOOD SYSTEM Broan Model 634 or 644 Roof Cap Broan Model 643 8” Round Wall Cap Warranty Broan Model 639 3¼” x 10” Standard Wall Cap Wall & Roof Caps Elbow Safety 8” Round Adjustable Elbow Upper Decorative Flue Operation Broan Model 401 Standard 3¼” x 10” Duct Ductwork 8” Round Standard Duct Adapter/damper 8” round (supplied with hood) For vertical discharge Lower Decorative Flue Adapter/dampers Cleaning Adapter/damper 3¼” x 10” (supplied with hood) For horizontal discharge 31130 or 31133
EQUIVALENT DUCT LENGTH CHART Kenmore range hoods are designed to perform efficiently when attached to long runs of duct. As a point of reference, this hood will function at approximately 80% of its rated air performance when 300 equivalent feet of 8” round ductwork is attached. Use this chart to calculate the equivalent duct length of your system. Note that 8” round is the minimum recommended duct size. HR0047 Straight Duct 8-in. round x 2-ft. long Equivalent length HR0048 Broan Model 643 8-in.
SELECT INSTALLATION TYPE Warranty 1. Plan where and how the ductwork will be installed. Install proper-sized ductwork, transition(s), elbow(s), and roof or wall cap. For best results, use a minimum number of transition and elbows. 2. The minimum hood distance above cooktop must not be less than 24’’. A maximum of 30’’ above cooktop is highly recommended for best capture of cooking impurities.
WIRING INSTALLATION WARNING: Improper grounding can result in a risk of electric shock. Consult a qualified electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance, in accordance with all applicable codes and standards. Turn off electrical power at service entrance before wiring.
PREPARE THE HOOD Warranty 1. Lay the hood on its back on a table. Remove grease filters by lifting the metal latch tab (1), pushing down on the filter (2) and tilting is towards you (3). 3 1 NOTE Safety Use a piece of cardboard to avoid damaging the table or the hood. 2 HD0376 2. Choose the opening: VERTICAL DISCHARGE: Using a Robertson or a Phillips no. 2 screwdriver, remove the 4 top metal plate retaining screws in order to clear the vertical discharge opening (see illustration beside).
PREPARE THE HOOD NOTE The following instructions are for the horizontal installation only. For a vertical installation, go to the “Install the hood” section on page 11. These Kenmore Elite Series range hoods are factory shipped with the blower mounted for a vertical discharge configuration. For a horizontal discharge configuration, disassemble the blower from the inner top of the hood (see illustrations below). It will be assembled to the inner back of the hood once the hood is mounted on the wall. 3.
INSTALL THE HOOD Warranty WARNING: When cutting or drilling into wall, do not damage electrical wiring and other hidden utilities. HD0374A 36¾” = BOTTOM OF HOOD 24” ABOVE COOKTOP 42¾” = BOTTOM OF HOOD 30” ABOVE COOKTOP 2. Center the upper flue mounting bracket with the center line previously drawn and place it flush with the ceiling. Use the upper flue mounting bracket as a template to mark the position of its screws. Drill the 3 screw holes using a 3/16” drill bit.
INSTALL THE HOOD INSTALL THE HOOD VERTICAL DISCHARGE ONLY: VERTICAL DISCHARGE ONLY: 6. Mount the 8” round adapter/damper (included in a separate box) to the hood using 4 no. 8 x 3/8” sheet metal screws (included). 7. Plug hood power cord into the outlet. Slide a 8” metal round duct over the adapter/damper. Use metal foil duct tape to seal the joint. HJ0037 HJ0041 FINALIZE THE INSTALLATION UPPER FLUE TOP CORNERS 1. Remove protective plastic film covering the lower flue only.
FINALIZE THE INSTALLATION 3. Slide up the upper flue until it is aligned with its mounting bracket. The bracket must be inside the flue. Secure the upper flue to its bracket using 2 no. 8 x 3/8” screws (included). See illustration beside. Warranty UPPER FLUE MOUNTING BRACKET FRONT VIEW UPPER NOTE FLUE Duct not shown in illustration to ease understanding. Safety 4. Remove protective plastic film covering the upper flue.
SERVICE PARTS 1 2 3 PART NO.