Kenmore _ARS Automatic Iron Filter MODEL NO. 625.349223 --- WARRANTY START UP/SETFING TIMER HOW IT WORKS --- CARE OF -- SPECIFICATIONS -- REPAIR PARTS (Use plastic bag and tie provided, to hang manuals nearby the filter for future reference.) PRINTED IN U.S.A.
WARRANTY I ] SEARS RESIDENTIAL WATER FILTER FULL ONE YEAR WARRANTY ON FILTER For one year from the date of purchase, when this water filter is installed and maintained in accordance with our instructions, Sears will repair, free of charge, defects in materials or workmanship in this water filter. FULL FIVE YEAR WARRANTY AGAINST LEAKS For five years from the date of purchase, Sears will furnish and install a new current model water filter tank, free of charge, if the tank develops a leak.
TABLE OF CONTENTS I I PAGE NO. SECTION 1 A. B. C. D. E. WATER FILTER START UP SAFETY GUIDES CHECK LIST OF ALL STEP-BY-STEP GUIDES TO INSTALL SANITIZING THE WATER FILTER PROGRAM THE TIMER ADJUSTMENT FOR POTASSIUM PERMANGANATE USE SECTION 2 HOW YOUR WATER FILTER WORKS A. FACE PLATE TIMER FEATURES B. IRON IN WATER/HOW FILTER REMOVES SECTION 3 A. B. C. D.
SECTION 1 I 1A. SAFETY GUIDES • Read all steps, guides and rules carefully before installing and using your new water filter. Follow all steps exactly to correctly install. Failure to follow them could cause personal injury or property damage. Reading this bookwill also help you to get all of the benefits from your water filter. • Your automatic filter will remove iron from your water supply as described on page 12. Also see the specifications on page 18.
SECTION 1 WATER FILTER START-UP I I lB. CHECK LIST OF ALL STEP BY STEP GUIDES TO INSTALL Refer to the Installation Manual, for step-by-step guides. part no. 7146611, To be sure you have done all the steps to install the filter, read the following list. Page numbers referred to are in the J_CLt__M_,_. UPPL _, _' Is the house water flow going INTO the filter valve INLET? Trace piping to be sure.., page 9. i/ Is the plumbing bypass valve (or 3 valves) set for SERVICE? . . . See FIG.
SECTION 1 WATER FILTER START-UP r ! lC. SANITIZING THE WATER Care is taken at the factory to keep your water filter clean and sanitary. Materials used to make the filter will not infect or contaminate your water supply, and will not cause bacteria to form or grow. However, during shipping, storage, installing and operating, bacteria could get into the filter. For this reason, sanitizing as follows is suggestedO when installing. 1. Press button [] on the and face HOLD plate until RCHG 4.
SECTION 1 WATER FILTER START-UP | J 1D. PROGRAM THE TIMER PRESENT TIME AND ] RECHARGE TIME (_ RECHARGE DAY DAY SET/CLEAR ON/CFF HOLD display buttons When the transformer is plugged into the electrical outlet, 12:00 AM, SUnday began to flash in the time display. Set the time of day, present day of week, and days/time of recharge, as follows. 1. a. SET TIME OF DAY Press the button [] flash. b. VACATION RECHARGE NOW 2. SET PRESENT a.
SECTION 1 WATER FILTER STAre-UP I I PROGRAM THE TIMER 1D, 3. SET DAYS OF RECHARGE IF YOU HAVE A WATER SOFTENER OR OTHER AUTOMATIC FILTER... A good water flow rate is needed for proper recharging and/or backwashing of all water conditioners• To help assure good water flow, you should offset the timers on each conditioner so recharges do not occur on the same days, or at the same time as follows. •. • Most Sears water softeners are factory set (many are adjustable) to recharge from 2:00 to 4:00 am. • .
SECTION 1 WATER FILTER START-UP I I 1E. ADJUSTMENT ii FOR POTASSIUM PERMANGANATE USE ii The filter is factory set to use about 2 ounces of potassium permanganate each recharge. That's how much is needed to keep the mineral bed working the way it should. However, if you recharge the filter more often than needed (see the table on page 8) less potassium permanganate is needed each time. The valve (FIG. 3) has a tube that raises and lowers into the bottle. It has 2 settings marked on it.
SECTION 2 HOW YOUR WATER FILTER WORKS I 2A. RECHARGE FACE PLATE _MER FEATURES NOW For times you expect to use more water than usual, use the RECHARGE NOW feature. Press the RECHARGE NOW-HOLD button [] and hold in for 3 seconds. RCHG begins to flash in the display and a recharge starts right away. You will have filtered water when the recharge is over in about 2 hours.
SECTION 2 Mowyour wATER JLTER WORKS I I 2A. TIMER "POWER-OUTAGE FACE PLATE TIMER MEMORY" 2. The display will show a time, but it will be flashing• The timer memory did not keep the time settings and they must be reset, pages 7 and 8. If electrical power to the timer goes off, the "memory" built into timer circuitry keeps all settings for 6 hours (minimum) or more. The display is blank and the filter will not recharge. When electrical power comes on, 1 of 2 things will happen. 1.
SECTION 2 .ow YourWATER FILTE. WORKS i __j 2B. IRON IN WATER/HOW FILTER REMOVES IT IMPORTANT: Sears water filters are sometimes installed alone in the water system, but most often other water treating equipment is needed. Always be sure to have your water tested by a qualified testing laboratory. If you need help, ask at your Sears store, or call Sears Water Line, 1-800-426-9345. Iron in water causes many problems, from mak;ng rust stains on clothing, plumbing fixtures, etc.
SECTION 2 HOW YOUR WATER RLTER WORKS I I I 2B. IRON IN WATER/HOW FILTER REMOVES IT FILTERED WATER OUT FILTERED WATER OUT WATER IN WATER IN FILL SERVICE Miner_ Bed BYPASS WATER OUT Nozzle & _ Bottle WATER IN I Potassium Permanganate I! Venturi _ _ Drain SOLUTION DRAW/RINSE Mineral Bed IMPORTANT: Avoid using water in the house while the filter is regenerating.
SECTION 3 3A. CHANGING CARE OFYOUR FILTER THE POTASSIUM HOW LONG DOES A BOTTLE OF POTASSIUM PERMANGANATE LAST? How long a bottle lasts depends on how often the filter regnerates and how much potassium permanganate is used (pages 8 and 9). You can use the chart below as a guide to tell you about how long it will last. Tube Set at "A" Mark Tube Set At "B" Mark 1 2 3 4 5 6 7 9 months 4 1/2 months 3 months 9 weeks 7 weeks 6 weeks 5 weeks 18 months 9 months WARNING: HANDLE THE BOTTLE WITH CARE.
SECTION 3 CARE OFYourRLTER I 3B. CLEANING THE NOZZLE AND VENTURI A clean nozzle and venturi (FIG. 9) is a must for the filter to work right. This small unit moves potassium permanganate solution from the bottle, into the mineral bed during solution draw (page 13). If the nozzle and venturi becomes plugged with iron, sand, silt, dirt, etc., it can not make the suction to move the solution. Without this solution during regeneration, the mineral bed will not be cleaned as it should.
SECTION 3 3C. CARE OFYOUR FILTER KEEP THE FILTER FROM FREEZING If the filter is installed where it could freeze (summer cabin, lake home, etc.), you must drain all water from it to stop possible freeze damage. To drain the filter 1. Close the shut-off valve on the house main water pipe, near the water meter or pressure tank. 2. Open a faucet in the filtered water pipes to vent pressure in the filter. 3. Looking at FIG. 10 on page 18, move the stem in a single bypass valve to bypass.
SECTION 3 CARE OFYOUR RLTER I I 3D. BEFORE YOU CALL FOR SERVICE... PROBLEM FILTER WILL NOT RECHARGE FILTER RECHARGES, BUT FILTERED WATER HAS IRON LOW WATER PRESSURE AT HOUSE FAUCETS NOTE: HELPFUL HINTS CHECKLIST CAUSE Manual bypass position valve(s) CORRECTION in bypass See FIG. 10, page 18. Move stern in a single bypass valve to SERVICE. In a 3-valve bypass, open the inlet and outlet valves, close the bypass valve.
SECTION 4 OTHER THINGS TOKNOW I I DIMENSIONS/SPECIFICATIONS 4A. BYPASS VALVES SINGLE-BRASS SINGLE-PLASTIC 3%" inlet-outletcentedines PULL STEM OUTWARD INLET-OUTLET FOR SERVICE FREEBOARD 18"-22" Inward FOr Bypass PUSH INWARD FOR SERVICE Bypass For 49" tank height 47" 3-VALVE SERVICE Close ByPass Valve Open Inter & Outlet Valves BYPASS Open Bypass Valve Close Inlet & Outtet Valves 55" Bypass VaI,R Outlet inlel Valve r [ L-2o.
SECTION 5 SERVICER'STECH. INFORMATION I I 5A. ELECTRICAL CONNECTIONS IMPORTANT: KEEP THIS TECHNICIAN MANUAL WITH YOUR WATER FILTER. IF REPAIRS ARE NEEDED, MUST HAVE THE INFORMATION ON THE FOLLOWING 8 PAGES. WIRING THE SCHEMATIC CIRCUIT BOARD TRANSFORMER 24VAC 11o VAC NC POSITION SWITCH'I_ O.
SECTION 5 SERVICER'S TECH. INFORMATION I I 5B. RECHARGE RECHARGE CYCLE TIMES times and Cycle Sequence SINGLE BACKWASH FILL DOUBLE BACKWASH 4 MIN. 4 MIN. BACKWASH -- 16 MIN. FAST RINSE -- 8 MIN. 80 MIN. 16 MIN. 80 MIN. 16 MIN. 8 MIN. 8 MIN. 112 MIN. 137 MIN. SOLUTION DRAW/RINSE BACKWASH FAST RINSE TOTAL (_ 1_) Includes valve positioning TO SET DOUBLE USE BUTTONS 1. REPEAT OTHER [] (SET/CLEAR), and [] ...................... (PRESENT SOLUTION DRAW .
SECTION 5 SERVICER'S TECH. INFORMATION I I 5C. AUTOMATIC DIAGNOSTICS ELECTRONIC DIAGNOSTIC The chart below shows the error codes that could appear, and the possible defects for each code. The face plate has a self-diagnostic function for the electrical system (except input power). The face plate monitors the electronic components and circuitsfor correct operation. If a malfunction occurs, an error code appears in the face plate display.
SECTION 5 SERVICER'S TECH. INFORMATION I I ! 5D. "QUICK-CHECK" IR_ TROUBLESHOOTING IN WATER]-.m,--P VISUAL CHECKS J 1 Is raw waterpipe plumbedto valveinlet? {_: I1:vPl_;bidnragibYhPoasSeSVna_VDe(,Sr_;_le_ervioe? 4 DoessOlutionboille have potassium permanganate remaining? I I_l_. %,Y.S_O iw_ _T%,CT I NG I ITIMER DISPLAY BLANK I OBSERVEVALVE CAM POSITION l Ele:tdcal power was oft I Reseta,I timer prngramming I I,N SERVICE POSITION I power cable, atl conneDtions)timer {oullst.
SECTION 5 SERVICER'S TECH. INFORMATION ! I 5E. ROTARY VALVE SERVICE BEFORE WORKING ON THE VALVE, TURN OFF THE WATER SUPPLY AND DISCONNECT FROM ELECTRICAL POWER. TO RELIEVE PRESSURE... ... 3 VALVE BYPASS: Close the inlet valve and open a filtered water faucet. Then close the outlet valve and open the bypass valve. •.. SEARS SPECIAL BYPASS: Slide the bypass valve stem to bypass position.
SECTION 5 SERVICER'S TECH. INFORMATION I I 5F. WATER FLOW THROUGH THE FILTER VALVE SERVICE CYCLE POSITION , SWITCH ,VALVE INLET (UNFILTERED WATER) VALVE OUTLET' (FILTERED WATEIq TOP MINERAL TANK Hard, unfiltered water enters the valve inlet port. Internal valve potting routes the water down andout the top distributor, into the mineral tank. The water is filtered as it passes through the mineral bed, then enters the bottom distributor.
SECTION 5 SERVICER'S TECH. INFORMATION I 1 iiii 5F. WATER FLOW THROUGH i i ii THE FILTER VALVE Ull SOLUTION DRAW AND RINSE POSITION ITCH ROTOR & DISC VENTURI I VALVE OUTLET WATER)' NOZZLE,._ SOLUTION FROM ...., BOTTLE / °°o I°,o feeder valve t DRAIN - TOP DISTRIBUTOR fqP 11' =. , seal on bib washer adj. After fill, timer/swffeh action allows the motor to turn the rotor and disc into SOLUTION DRAW position.Water flow is directed to the nozzle.
SECTION 5 SERV,CER'S TEC..,NFORMAT,O. I I 5F. BACKWASH WATER FLOW THROUGH THE FILTER VALVE CYCLE FAST RINSE CYCLE POSITION SWITCH POSITION ROTOR & DISC FLOW PLUG ROTOR & DISC POSITION SWITCH DRAIN INLET OUTLET DISTRIBUTOR _. INLET TOP DISTRIBUTOR OUTLET BOTTOM "-"_ DISTRIBUTOR Switchingaction again allOWSthe motorto turnthe rotor & disc to place the valve in BACKWASH, stoppingwater flow to the nozzle.
NOTES [ J 27
SECTION 6 REPAIR PARTS I I SEARS L _'_ 12 10 _'_ F IRON FILTER MODEL NO. 625.349223 _ T _ AUTOMATIC I._ v*LvE COVER SCREWS €21 ...
SECTION 6 REPAIR PARTS I I SEARS AUTOMATIC IRON FILTER MODEL NO. 625.349223 PARTS LIST i KEel PART NO NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 7066497 7105047 7088855 7096183 0900215 7079092 7088033 7088041 0900300 7121734 7084330 7118333 7095373 7144449 7103972 0900291 7141530 7146734 7092202 20 21 4015000 0501783 DESCRIPTION Bottom Distdbutor Repl. Distributor(Incl. Key No. 1) Top Distributor O-Ring, 2-3/4 x 3 O-Ring, 13/16 x 1-1/16 O-Ring, 2-7/8 x 3-1/4 Clamp Retainer (2 req.
SECTION 6 REPAIR PARTS I I SEARS AUTOMATIC IRON FILTER MODEL NO. 625.
SECTION 6 REPA,R PARTS I I SEARS AUTOMATIC IRON FILTER MODEL NO. 625.349223 VALVE ASSEMBLY PARTS LIST KEY NO. PART NUMBER 51 52 53 54 55 56 57 58 59 60 61 62 62 64 65 66 67 68 69 70 71 72 73 74 75 7131755 7133008 0900857 7117808 0503288 7113927 7142942 7030585 0509537 0900041 7141239 7116713 0507369 0507615 0900570 2207800 0900535 7082053 0900064 7081201 7081104 1202600 7089267 1148800 7114533 [] DESCRIPTION Screw, #6-20 x 7/8 (2 req.) Motor Screw, #6-20 x 3/8 (2 req.
Kenrnor'e Automatic Iron Filter OWNERS MANUAL SERVICE Your Sears Water Filter has added value when you consider that Sears has service units nationwide staffed with Sears trained technicians - professional technicians specifically trained on Sears products, having the parts, tools and equipment to ensure that we meet our pledge to you - "We Service What We Sell." MODEL NO. 625.349223 The model number of your water filter is found on the rating decal. This decal is on the backside of the filter top cover.